CASIO CELVIANO AP-S200WE (01) PDF Document

Use the AC adaptor model AD-E24250LW supplied with the Digital Piano. Connect the power cord to the AC adaptor first. Next, connect the AC adaptor to the power supply terminal (DC 24V) on the piano. Finally, plug the power cord into a household wall outlet. Always turn off the power before connecting or disconnecting the adaptor.

To turn the power on, press the Power button. Each touch button will blink while the instrument is starting up; when all buttons remain lit, it is ready for use. If the power does not come on with a light press, press the button again firmly.

To turn the power off, press and hold the Power button for about 2 seconds. The instrument will enter standby mode. It is recommended to disconnect the AC adaptor from the outlet if you do not intend to use the piano for an extended period.

The CASIO CELVIANO AP-S200WE features several high-quality grand piano tones:

GRAND PIANO CONCERT: A full concert grand piano tone with dynamic and natural tone changes.

GRAND PIANO BRIGHT: A bright and clear piano tone.

GRAND PIANO MELLOW: A warm and calm piano tone.

There are two primary methods to select a single tone:

1. Touch the GRAND PIANO button to immediately select the GRAND PIANO CONCERT tone.

2. While holding down the GRAND PIANO button, press a keyboard key from G3 to C#5. The tone names are marked above the keys for easy identification.

To play two tones simultaneously (Layer):

1. While holding down the GRAND PIANO button, press the C7 key to turn the Layer function On.

2. The first tone you select is assigned to the Upper1 part. To select a tone for the second part (Upper2), hold down the GRAND PIANO button and press a key from G3 to C5.

3. To turn layering off, press the GRAND PIANO button alone or hold it and press the C7 key again.

The Split function allows you to play a bass tone in the lower section of the keyboard while keeping another tone in the treble section.

1. While holding down the GRAND PIANO button, press the C#5 key (marked BASS).

2. The left side of the keyboard will play the BASS tone, while the right side will remain the previously selected tone.

3. Selecting any tone other than the BASS tone will cancel the split state.

The Duet function splits the keyboard so the left and right sides have the same pitch range.

1. While holding down the FUNCTION button, press the F2 key (Duet Mode).

2. Select the desired setting: Off (Turns off Duet), On (Turns on Duet), or Pan (Left keyboard sound outputs from the left speaker, right keyboard from the right speaker).

3. In Duet mode, the pedals function differently: the left pedal is the damper for the left side, the right pedal is the damper for the right side, and the center pedal is the damper for both sides.

Touch the METRONOME button to start or stop the metronome.

To change the beat, hold the METRONOME button and press a key from C#3 to Bb3 (representing Off to 9 beats).

To set the tempo as a number (20 to 255 bpm), hold the METRONOME button and use keys A0 through F#1 as numeric input keys (0 to 9).

To use Tap Tempo, hold the METRONOME button and tap the Bb2 key two or more times at the desired speed.

While holding down the GRAND PIANO button, press one of the following keys to set the sensitivity:

Eb1: Off (Volume remains constant regardless of key pressure)

E1: 1 (Light – easier to produce loud sounds)

F1: 2 (Medium light)

F#1: 3 (Normal – standard setting)

G1: 4 (Medium heavy)

Ab1: 5 (Heavy – difficult to produce loud sounds)

While holding down the GRAND PIANO button, use the following keys to adjust the overall pitch within a range of -12 to +12 semitones:

C#1: Lowers the pitch by one semitone.

D1: Raises the pitch by one semitone.

C#1 + D1: Resets the pitch to the default setting (0).

1. Ensure the [Recorder] setting is set to MIDI Recorder by holding FUNCTION and pressing B3.

2. Touch the REC button. It will blink red to indicate recording standby.

3. Start playing; recording begins automatically and the button stays lit red.

4. To end recording, touch the REC button again. The button will return to white.

5. To play back the recording, touch the Play/Stop button.

Note: Formatting deletes all data on the drive. Use FAT32 or exFAT formatted drives.

1. Insert the USB flash drive into the USB Type A port.

2. Press and hold the FUNCTION button.

3. Press the C2 key (Format). The right side of the beat indicator will blink.

4. Press the C1 key (Execute). The indicators above SOUND MODE and Play/Stop will light up sequentially during formatting.

5. Once formatting begins, release the FUNCTION button.

To pair for Bluetooth Audio:

1. Attach the supplied Wireless MIDI and audio adaptor to the USB Type A port.

2. While holding down the FUNCTION button, press the C#1 key (Wireless Audio Pairing). The Power button will flash blue.

3. On your smart device’s Bluetooth settings, select “WU-BT10 AUDIO”.

4. When connected, a notification tone sounds and the Power button lights up blue.

1. Press and hold the FUNCTION button.

2. Press the A0 key (Factory Reset). The piano enters standby and the FUNCTION button blinks.

3. Press the C1 key (Execute) to start the reset. Do not release the FUNCTION button until you press C1.

4. Release the FUNCTION button. When the process is complete, all touch buttons on the panel will light up.

If no sound is produced when keys are pressed, check the following:

1. Is the volume knob turned down? Turn the volume up.

2. Are headphones or conversion plugs left in the PHONES/OUTPUT jacks? Unplug them.

3. Is [Local Control] turned Off? Set it to On by holding FUNCTION and pressing F6.

4. Is [Speaker Out] set to Off? Set it to Auto or On by holding FUNCTION and pressing Eb7.