CANON FAXPHONE L80 (01) PDF MANUAL

After unpacking, check that you have the following:

Machine

FX-3 S Cartridge

Support trays (2)

Multi-purpose tray

Multi-purpose tray cover

Document support

Handset

Handset cradle

Plugs with pins (2)

Paper loading warning label

Power cord

Telephone line cord

Documentation (Set-Up Instructions, Basic Guide, Warranty, Registration card (for USA only))

FAXPHONE L80 Software CD-ROM

Destination labels

You need a USB cable (less than 16.4 ft./5 m) to connect your machine to a computer.

To lift the machine, hold it firmly and level as illustrated.

1. Place the machine on a flat surface.

2. Remove all shipping tapes from the exterior of the machine.

3. Gently open the operation panel (it only opens partially) and remove the protective sheet from the ADF.

4. Close the operation panel by pressing at the center until it locks into place.

Do not remove the USB label on the back of the machine at this stage.

1. Attach the paper loading warning label.

2. Insert the multi-purpose tray into the slots on the machine.

3. Insert one of the support trays into the slots above the delivery slot.

4. Insert the other support tray into the slots above the ADF.

5. Insert the document support into the slots on the machine.

Place the multi-purpose tray cover on the machine after loading paper (see the next page).

1. Insert a stack of paper into the multi-purpose tray (print side facing you and top edge first), then adjust the paper width guides to the width of the paper.

2. Attach the multi-purpose tray cover to prevent dust accumulating inside the machine.

1. Insert the plugs with pins into the holes on the handset cradle.

Do not push the pins all the way into the plugs at this stage.

2. Turn the machine so that the left side is facing you.

3. Insert the plugs (with the handset cradle) into the holes on the machine.

4. Carefully push the pins into the plugs as far as they will go.

If the pins are not pushed fully into the plugs, the handset cradle will not be securely attached to the machine.

The machine has the following jacks: Telephone line jack, External device jack, Handset jack.

To connect the telephone line cord: Connect the supplied cord to the telephone line jack. Then connect the other end to the telephone line jack on your wall.

To connect an external device (optional): Connect the cord of an extension telephone, answering machine or data modem to the external device jack.

To connect the handset: Place the handset on the cradle. Connect the handset cord to the handset jack.

Connect external devices as follows:

Telephone or answering machine:

Telephone line connected to Machine, Machine connected to Telephone or answering machine.

Telephone and answering machine:

Telephone line connected to Machine, Machine LINE TEL connected to Answering machine, Answering machine connected to Telephone.

Built-in computer modem and telephone:

Telephone line connected to Machine, Machine LINE TEL connected to Computer, Computer connected to Telephone.

You must complete all the steps in this document to receive faxes properly.

When the power cord is plugged into the machine and into the wall outlet, the machine is turned on. The LCD displays PLEASE WAIT, then PUT IN CARTRIDGE. The LCD returns to the standby display when you install the FX-3 S Cartridge.

The machine does not have a power switch.

1. Lift the latch and open the front cover.

2. Remove the FX-3 S Cartridge from its protective bag.

3. Gently rock the cartridge from side to side a few times to distribute the toner evenly inside it.

Print quality may be poor if the toner is unequally distributed.

Do not open the drum protective shutter on the cartridge.

4. Place and hold the cartridge on a flat, clean surface, then gently pull the plastic tab straight out to remove the plastic seal.

Use a firm, even pull to remove the seal.

5. Hold the cartridge by its handle and insert it into the machine as far as it will go, making sure that its side tabs are aligned with the guides inside the machine.

Always hold the cartridge by its handle.

6. Use both hands to close the front cover.

The FX-3 S Cartridge is a starter cartridge supplied with the machine. The replacement cartridge is the FX-3 Cartridge separately available from Canon.

1. Press Function.

2. Press Receive Mode.

3. Press up or down until the mode you want appears in the LCD (e.g., Fax/Tel Mode).

You can select from the following:

Fax/Tel Mode: When the handset or the extension telephone is connected to the machine, the machine automatically switches between faxes and voice calls.

MANUAL MODE: When the handset or the extension telephone is connected to the machine, you can receive faxes by pressing Start/Copy before hanging up the handset or the extension telephone.

ANS.MACHINE MODE: If you want to receive faxes automatically and route voice calls to an answering machine.

FAX ONLY MODE: If you use your machine to receive only faxes.

DRPD: To distinguish between fax and voice calls by using Distinctive Ring Pattern Detection.

4. Press Set to return to standby mode.

Before sending a fax, you MUST register the fax number, your name, and the current date and time in the machine. For details, see p. 2-5 of the Basic Guide.

For details on setting FAX ONLY MODE or DRPD mode, see p. 8-2 of the User’s Guide included in the CD-ROM.

The DRPD mode requires subscription to a DRPD service. For more information, contact your local telephone company.

DO NOT connect the USB cable before installing the software.

When installing the software in Windows XP or Windows 2000, log onto the system as a member of the Administrator group.

If the Found New Hardware Wizard appears, click Cancel, and follow this procedure.

1. Insert the CD-ROM into your CD-ROM drive.

2. If AutoRun is enabled, the installation starts automatically.

If installation does not start automatically, choose Run… from the Start Menu. Type D:\SETUP.EXE (if your CD-ROM drive is drive D:) in the command line and click OK.

3. Click Install Printer Driver to start installation.

4. Follow the on-screen instructions to complete the installation process.

During installation, follow these guidelines:

Click Next or Yes to move from one dialog box to the next.

Be sure to wait for Windows to complete each setup step. If you hear the computer working, wait until it is done.

If the Digital Signature Not Found screen appears, click Yes to continue.

5. When prompted, remove the label from the USB port on the back of the machine. Then connect the USB cable to the machine and your computer.

For Windows 98/Me:

Wait for the system to complete the installation of the printer driver.

For Windows 2000:

When the Found New Hardware Wizard appears during the setup, choose the following:

Search for a suitable driver for the printer. (Do not display a list of drivers.)

Search only on the installation disk. (Click CD-ROM drives only, and clear the other options.)

For Windows XP:

When the Found New Hardware Wizard appears during the setup, choose the following:

Select Install the software automatically (Recommended).

When the printer driver is installed, click Finish to close the Found New Hardware Wizard. Then click Yes to continue with the setup.

When the setup is finished, if prompted, restart Windows.

Remember to register your machine to ensure product support. The serial number is located on the back of the machine.