CAMRY CR 2841 (01) PDF Document

Please read carefully and keep for future reference. The manufacturer is not responsible for any damages due to misuse.

1. The CAMRY CR 2841 is for indoor use only. Do not use it for any purpose not compatible with its application.

2. The applicable voltage is 5V 1A. It is not appropriate to connect multiple devices to one power outlet for safety reasons.

3. Be cautious when using around children. Do not let children play with the product or use it without supervision.

4. This device may be used by children over 8 years of age and persons with reduced physical, sensory, or mental capabilities under supervision.

5. After use, always gently remove the plug from the power outlet by holding the outlet with your hand. Never pull the power cable.

6. Never put the power cable, plug, or the whole device in water. Do not expose the product to atmospheric conditions like direct sunlight or rain, and never use it in humid conditions.

7. Periodically check the power cable. If damaged, it should be replaced by a professional service to avoid hazards.

8. Never use the product with a damaged power cable, if it was dropped or damaged, or if it does not work properly. Do not attempt to repair it yourself. Always take it to a professional service location.

9. Do not place the product on or close to hot surfaces or kitchen appliances like an electric oven or gas burner.

10. Never use the product close to combustibles.

11. Do not let the cord hang over the edge of a counter or touch hot surfaces.

12. Never leave the product connected to the power source without supervision.

13. To provide additional protection, it is recommended to install a residual current device (RCD) in the power circuit with a rating not more than 30 mA. Contact a professional electrician for this.

14. If using the device in a bathroom, remove the power plug from the socket after use as water proximity presents a risk even when the device is turned off.

15. Do not allow the device or power adaptor to get wet. If it falls into water, immediately remove the plug or adaptor from the socket. Have it checked by a qualified electrician before using it again.

16. Do not touch the device or power adaptor with wet hands.

17. The device must be turned off after every use.

18. Never use this device close to water, e.g., under a shower, in a bathtub, or above a sink filled with water.

19. If the device uses a power adaptor, do not cover it as this can cause a dangerous temperature rise.

20. The cutting scissors are very sharp. Use caution during assembly, dismantling, and cleaning. Do not touch any elements of the moving blade during operation.

21. DO NOT CHARGE THE BATTERY FOR LONGER THAN 48 HOURS, as this can cause irreversible damage.

22. The charging process should be conducted in temperatures between 5-35 degrees Celsius.

23. Do not wash the blades in water.

24. Only change comb attachments when the device is switched off.

The parts of the CAMRY CR 2841 are as follows:

1. Blade Head

2. Cutting Length Switch

3. Speed button

4. Power Button / Safety Lock

5. LCD Display, which includes:

5a. Oil Indicator

5b. Speed Indicator

5c. Battery Remaining Capacity

5d. Charge Indicator

6. Charging Socket

7. Combs

7a. Cleaning Brush

7b. Oil bottle

To charge the CAMRY CR 2841, follow these steps:

1. Plug the power cord into the charging socket (6) on the clipper.

2. Plug the charger into a 220-240V~ 50/60Hz mains power outlet.

3. When the power adapter is plugged in, you will hear a “beep” and the charging indicator (5d) will start blinking from bottom to top.

4. When the battery is fully charged, there will be another “beep”. The battery capacity reminder (5c) will show 100% and the charging light (5d) will blink at the same time.

The charging time is about 2 hours, which provides a running time of about 210 minutes. When the battery level reaches 10%, 5%, and 0%, it will beep 3 times. When the battery reduces to 10%, the charging indicator (5d) will start to blink. You can also use the clipper while it is charging if the battery runs out.

The CAMRY CR 2841 has 5 speed levels available, ranging from 5000-7000 RPM. To control the speed, press the “+” or “-” button (3). Each press will adjust the speed by 500 RPM, which is shown on the speed indicator (5b).

To turn the CAMRY CR 2841 on or off, press the power button (4). To turn the safety lock on or off, press and hold the power button (4) for 3 seconds.

When the CAMRY CR 2841 has been working for a total of 60 minutes, the oiling indicator (5a) will begin to blink. This is a reminder to clean and oil the blade.

1. Select the desired cutting length by turning the cutting length adjustment knob (2). The available settings are 0.8, 1.1, 1.4, 1.7, and 2.0mm.

2. To change the comb attachment, ensure the clipper is turned off. Unclip the current comb and clip on the new one.

3. Start cutting by running the trimmer with the comb attachment against the direction of hair growth. This should be done slowly and at a steady speed.

4. Remember to regularly clean the trimmer and cutting head of any hair during and after use.

Clean the CAMRY CR 2841 after each use. Make sure the product is turned off and unplugged.

1. Push the edge of the cutting head with your thumb until it opens.

2. Clean the cutting parts with the supplied cleaning brush.

3. Clean the inside of the product with the supplied cleaning brush.

4. Reinstall the cutting head back to the clipper body. Make sure the bottom of the cutting head is aligned with the clipper body recess, then push the cutting head inward until it clicks into place.

5. Clean the casing with a dry cloth.

You should oil the blade of your CAMRY CR 2841 when the oiling indicator (5a) begins to blink, or after every five uses. To oil the blade, drop 2-3 drops of machine oil into the space indicated in the user manual’s diagram for oiling.

The technical specifications for the CAMRY CR 2841 are:

Power Nom.: 5W

Power: 5V-1A