BRAUN SERIES 3 5414 (01) PDF Document

To charge the BRAUN SERIES 3 5414, use the special cord set to connect the shaver or the charging stand to an electrical outlet with the motor switched off.

When charging for the first time or when the shaver is not used for a few months, leave the BRAUN SERIES 3 5414 to charge continuously for 4 hours.

Once the BRAUN SERIES 3 5414 is completely charged, discharge it through normal use. Then recharge it to full capacity. Subsequent charges will take about 1 hour.

A 5-minute quick charge is sufficient for one shave.

A full charge provides up to 45 minutes of cordless shaving time depending on your beard growth. However, the maximum battery capacity for the BRAUN SERIES 3 5414 will only be reached after several charging and discharging cycles.

The green charging light on the BRAUN SERIES 3 5414 shows the charge status of the batteries. It blinks when the shaver is being charged or switched on. When the battery is fully charged, all green charging lights shine permanently, provided the BRAUN SERIES 3 5414 is connected to an electrical outlet.

The red low-charge light on the BRAUN SERIES 3 5414 flashes when the battery is running low. You should be able to finish your shave.

Press the on/off switch to operate the BRAUN SERIES 3 5414. The flexible shaving foils automatically adjust to every contour of your face.

To trim sideburns, a moustache, or a beard, slide the long hair trimmer of the BRAUN SERIES 3 5414 upwards.

For precise handling in hard to shave areas of the BRAUN SERIES 3 5414, such as under the nose, slide the precision mode switch to the right position. One foil will be lowered.

For best results with the BRAUN SERIES 3 5414, follow these 3 simple steps:

1. Always shave before washing your face.

2. At all times, hold the BRAUN SERIES 3 5414 at right angles (90 degrees) to your skin.

3. Stretch your skin and shave against the direction of your beard growth.

Switch the BRAUN SERIES 3 5414 on in its cordless mode. Rinse the shaver head and the precision mode switch under hot running water until all residues have been removed. You may use liquid soap without abrasive substances. Rinse off all foam and let the BRAUN SERIES 3 5414 run for a few more seconds.

Next, switch off the BRAUN SERIES 3 5414, remove the Foil and Cutter cassette and let it dry.

If you regularly clean the BRAUN SERIES 3 5414 under water, apply a drop of light machine oil onto the long hair trimmer and Foil and Cutter cassette once a week.

The BRAUN SERIES 3 5414 should be cleaned after each foam usage.

Switch off the BRAUN SERIES 3 5414. Remove the Foil and Cutter cassette and tap it out on a flat surface.

Using a brush, clean the inner area of the shaver head. Do not clean the Foil and Cutter cassette of the BRAUN SERIES 3 5414 with a brush as this may damage it.

To maintain 100 percent shaving performance, replace the Foil and Cutter cassette of the BRAUN SERIES 3 5414 when the replacement light for shaving parts comes on, which happens after about 18 months or when worn.

The replacement light will remind you during the next 7 shaves to replace the Foil and Cutter cassette of the BRAUN SERIES 3 5414. Then the shaver will automatically reset the display.

After you have replaced the Foil and Cutter cassette on the BRAUN SERIES 3 5414, press the on/off switch for at least 5 seconds to reset the counter. While doing so, the replacement light blinks and goes off when the reset is complete.

In order to maintain the optimum capacity of the rechargeable batteries in the BRAUN SERIES 3 5414, the shaver has to be fully discharged by shaving every 6 months approximately. Then recharge the BRAUN SERIES 3 5414 to full capacity.