BRAUN SERIES 9 9030S (01) PDF Document

Your BRAUN SERIES 9 9030S is provided with a special cord set, which has an integrated Safety Extra Low Voltage power supply. Do not exchange or tamper with any part of it, otherwise there is risk of an electric shock. Only use the special cord set provided with your appliance.

If the appliance is marked with the symbol 492, you can use it with any Braun power supply coded 492-XXXX.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the safe use of the appliance and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children unless they are older than 8 years and supervised.

Do not shave with a damaged foil or cord.

Yes, the BRAUN SERIES 9 9030S shaver is suitable for cleaning under running tap water. You must detach the shaver from the power supply before cleaning it in water.

Certain models (9095cc w&d / 9040s w&d) are also suitable for use in a bath or shower. For safety reasons, these specific models can only be operated cordlessly.

Keep the oil bottle out of reach of children. Do not swallow the oil and do not apply it to your eyes. Dispose of the bottle properly when it is empty.

To prevent the cleaning fluid from leaking, ensure that the Clean&Charge Station is placed on a flat surface. When a cleaning cartridge is installed, do not tip, move suddenly or transport the station in any way as cleaning fluid might spill out of the cartridge. Do not place the station inside a mirror cabinet, nor place it on a polished or lacquered surface.

The cleaning cartridge contains a highly flammable liquid so keep it away from sources of ignition. Do not expose it to direct sunlight and cigarette smoking, nor store it over a radiator.

Do not refill the cartridge and use only original Braun refill cartridges.

Prior to first use, remove the protection foil, if any, from the shaver display. Connect the shaver to an electrical outlet by snapping the special cord set (11) into the power socket (10). For cc models, you can also charge via the Clean&Charge Station.

• When charging for the first time, charge continuously for 1 hour.

• A full charge provides up to 50 minutes of cordless shaving time. This may vary according to your beard growth and environmental temperature.

• Recommended ambient temperature for charging is 5 °C to 35 °C. The battery may not charge properly or at all under extreme low or high temperatures.

• Recommended ambient temperature for shaving is 15 °C to 35 °C.

• Do not expose the appliance to temperatures higher than 50 °C for extended periods of time.

• When the shaver is connected to an electrical outlet, it may take some minutes until the display illuminates.

The shaver display shows the charge status of the battery when connected to an electrical outlet:

• During charging the respective battery segment will blink.

• When fully charged all battery segments will light up for a few seconds then the display turns off.

The low-charge light flashes red when the battery is running low. You should be able to finish your shave. When switching off the shaver, a beep sound will remind you of the low charge status.

For models 9095cc w&d/9090cc, the last 9 minutes of remaining shaving time are displayed in digits.

Press the on/off switch to operate the shaver. For a perfect dry shave, follow these tips:

1. Always shave before washing your face.

2. At all times, hold the shaver at the right angle (90°) to your skin.

3. Stretch your skin and shave against the direction of your beard growth.

To shave hard-to-reach areas (e.g., under the nose), slide the MultiHeadLock switch down to lock the shaver head. The shaver head can be locked in five positions. To change position, move the shaver head with your thumb and forefinger back or forth. It will automatically click into the next position.

For automatic cleaning in the Clean&Charge Station, the head lock should be released.

To trim sideburns, moustache, or beard, press the release button and slide the long hair trimmer upwards.

If the shaver has run out of power (discharged), you may also shave with the shaver connected to an electrical outlet via the special cord set. Note that this is not possible for wet & dry models 9095cc w&d/9040s w&d, which can only be operated cordlessly for safety reasons.

The travel lock prevents the motor from starting unintentionally, for example when storing it in a suitcase.

• Activation: By pressing the on/off switch for 3 seconds the shaver is locked. This is confirmed by a beep sound and the lock symbol in the display. Afterwards the display turns off.

• Deactivation: By pressing the on/off switch for 3 seconds the shaver is unlocked again.

• Switch on the shaver (cordless) and rinse the shaver head under hot running water until all residues have been removed. You may use liquid soap without abrasive substances. Rinse off all foam and let the shaver run for a few more seconds.

• Next, switch off the shaver, press the release buttons to remove the Foil & Cutter cassette and let it dry completely.

• If you regularly clean the shaver under water, then apply once a week a drop of light machine oil on top of the Foil & Cutter cassette.

Switch off the shaver. Remove the Foil & Cutter cassette and tap it out on a flat surface. Using the brush, clean the inner area of the pivoting head. Do not clean the cassette with the brush as this may damage it.

The Foil & Cutter cassette can be attached either way. There is no impact on the shaving performance.

• Remove the protection foil if any from the Clean&Charge Station display.

• Press the lift button at the rear side of the Clean&Charge Station to lift up the housing.

• Hold the cleaning cartridge down on a flat, stable surface (e.g. table).

• Carefully remove the lid from the cartridge.

• Slide the cartridge from the rear side into the base of the station until it snaps into place.

• Slowly close the housing by pushing it down until it locks.

• Connect the station to an electrical outlet by snapping the special cord set into the power socket.

Insert the shaver head with the front showing and released head lock into the cleaning station.

Important: The shaver needs to be dry and free from any foam or soap residue!

The contacts on the back of the shaver need to align with the contacts in the station. Push the shaver in the correct position. A beep sound confirms that the shaver sits properly in the station. Charging will start automatically.

When the cleaning indicator lights up in the shaver display, insert the shaver into the Clean&Charge Station as described for charging and press the start button.

The hygiene status will be analyzed and shown by the cleaning program indicators on the Clean&Charge Station display (for applicable models).

If the status light does not shine (the station switches to stand-by after about 10 minutes), press the start button twice. Otherwise, cleaning will not start. For best shaving results, we recommend cleaning after each shave.

The cleaning process consists of several cycles, in which cleaning fluid is flushed through the shaver head. Depending on your Clean&Charge Station model and/or program selected, the cleaning time takes up to 3 minutes, followed by an active drying phase of about 40 minutes, during which a fan is running.

Afterwards, charging will resume, which is indicated in the shaver display. When the shaver is fully charged the display turns off.

For models 9095cc w&d/9090cc/9075cc:

• short economical cleaning

• normal level of cleaning

• high intensive cleaning

For models 9070cc/9050cc:

• One standard cleaning program is included.

Hold the Clean&Charge Station with one hand and tilt the shaver slightly to the front to release it.

When the level indicator lights up permanently red, the remaining fluid in the cartridge is sufficient for about 3 more cycles. When the level indicator blinks red, the cartridge needs to be replaced (about every 3 weeks when used daily).

After having pressed the lift button to open the housing, wait for a few seconds before removing the used cartridge to avoid any dripping. Before discarding the used cartridge, make sure to close the openings using the lid of the new cartridge, since the used cartridge will contain contaminated cleaning solution.

The hygienic cleaning cartridge contains ethanol or isopropanol. Each cartridge, if not used daily, should be replaced after approximately 8 weeks to ensure optimal disinfection. The cleaning cartridge also contains lubricants for the shaving system, which may leave residual marks on the outer foil frame and the cleaning chamber of the Clean&Charge Station. These marks can be removed easily by wiping gently with a damp cloth.

Braun recommends changing your shaver’s Foil & Cutter cassette every 18 months to maintain your shaver’s maximum performance.

Available accessories include:

• Foil & Cutter cassette: 90S/90B

• Cleaning cartridge Clean&Charge Station: CCR

• Braun Shaver cleaner spray

The BRAUN SERIES 9 9030S contains batteries and/or recyclable electric waste. For environment protection do not dispose of it in household waste, but for recycling take it to electric waste collection points provided in your country.

The cleaning cartridge can be disposed of with regular household waste.

SHAVER

CLEAN&CHARGE STATION