BEYERDYNAMIC AVENTHO WIRELESS (01) PDF Document

When you connect the BEYERDYNAMIC AVENTHO WIRELESS headphones, please make sure that the volume level is set to minimum. Adjust the volume level only after putting on the headphones.

Excessively high volumes and long listening times may cause hearing damage. Hearing defects always constitute an irreversible impairment of hearing ability. It is advisable to keep listening times as short as possible at high volume levels.

Headphones drastically reduce the perception of external sounds. Using the BEYERDYNAMIC AVENTHO WIRELESS in road traffic can be potentially dangerous. The user’s hearing must not be impaired to the extent that it causes road safety risks.

Avoid sudden movements when using the BEYERDYNAMIC AVENTHO WIRELESS with the wire. You might seriously hurt yourself especially if you wear piercings, earrings, glasses, or similar items where the wire can get caught.

The box contains the following items:

1. BEYERDYNAMIC AVENTHO WIRELESS headphones

2. Jack connection audio cable 3.5 mm

3. Charging cable USB-A to USB-C

4. Soft bag

5. Warranty booklet

6. Quick Start Guide

Hold the BEYERDYNAMIC AVENTHO WIRELESS on the headband and pull it out of the soft bag. Rotate the two ear cups inward so that the ear pads are facing each other.

Rotate the two ear cups inward as indicated by the arrows on the cups. Hold the BEYERDYNAMIC AVENTHO WIRELESS and put it into the soft bag with the ear cups first.

To achieve the best sound and ambient noise attenuation, follow these tips:

1. Select the appropriate lock-in position on both sides of the headband.

2. Adjust the angle of the ear pads.

3. Place the BEYERDYNAMIC AVENTHO WIRELESS centrally on your ears.

The BEYERDYNAMIC AVENTHO WIRELESS features the following components:

1. Microphone

2. USB connection for charging cable (USB-C)

3. LED

4. Button

5. Jack connector 3.5 mm for audio cable

6. Touch pad

Hold down the button on the BEYERDYNAMIC AVENTHO WIRELESS for approximately 2 seconds. The LED will illuminate red once.

Hold down the button on the BEYERDYNAMIC AVENTHO WIRELESS for approximately 6 seconds. The LED will illuminate red once and then go out.

Follow these steps:

1. When the BEYERDYNAMIC AVENTHO WIRELESS is turned off, press the button for 6 seconds to start the Bluetooth mode. The LED will rapidly flash blue and red in turns.

2. Activate the Bluetooth function on your player and search for new devices if necessary.

3. Select “beyerdynamic Aventho wireless” under the available devices in the Bluetooth menu of your player and pair both devices.

Hold down the button of the turned-off BEYERDYNAMIC AVENTHO WIRELESS for more than 10 seconds. This will cause the headphones to switch into pairing mode and clear the list of players simultaneously.

Briefly tap the touch pad on the BEYERDYNAMIC AVENTHO WIRELESS twice.

Drag your finger forwards on the touch pad of the BEYERDYNAMIC AVENTHO WIRELESS.

Drag your finger backwards on the touch pad of the BEYERDYNAMIC AVENTHO WIRELESS.

Drag your finger forwards on the touch pad of the BEYERDYNAMIC AVENTHO WIRELESS and hold it for at least one second.

Drag your finger backwards on the touch pad of the BEYERDYNAMIC AVENTHO WIRELESS and hold it for at least one second.

Drag your finger upwards on the touch pad of the BEYERDYNAMIC AVENTHO WIRELESS and hold it. The volume is gradually increased until the maximum is achieved, indicated by an acoustic signal.

Drag your finger downwards on the touch pad of the BEYERDYNAMIC AVENTHO WIRELESS and hold it. The volume is gradually decreased until the minimum is achieved, indicated by an acoustic signal.

Press the centre of the touch pad on the BEYERDYNAMIC AVENTHO WIRELESS for approximately two seconds.

Briefly tap the touch pad on the BEYERDYNAMIC AVENTHO WIRELESS twice.

Press the centre of the touch pad on the BEYERDYNAMIC AVENTHO WIRELESS for approximately two seconds.

Press the centre of the touch pad on the BEYERDYNAMIC AVENTHO WIRELESS for approximately two seconds.

We recommend using the supplied USB charging cable only to connect the BEYERDYNAMIC AVENTHO WIRELESS to any USB compliant USB port supplying voltage.

During charging, the LED on the BEYERDYNAMIC AVENTHO WIRELESS is flashing red. As soon as the LED is permanently illuminated red, the rechargeable battery is completely recharged.

The RF frequency range is 2.4000 to 2.4835 GHz.

The transmission power is 10 mW.

The operating temperature range is 0 to 40 degrees Celsius.

The charging temperature range is 10 to 40 degrees Celsius.

Old batteries may contain substances that are harmful to your health and the environment. Do not throw used battery packs into the fire due to the danger of explosion. Dispose of used batteries always according to the applicable disposal regulations. Please dispose of discharged batteries only.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, you can try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4. Consult the dealer or an experienced radio or TV technician for help.

Important: To avoid malfunction, use only one finger when you use the touch pad of the BEYERDYNAMIC AVENTHO WIRELESS.

The descriptions in the documentation refer specifically to the firmware version 1.0 installed on the BEYERDYNAMIC AVENTHO WIRELESS.

Yes, after the initial pairing process is successful, each time when turning on the BEYERDYNAMIC AVENTHO WIRELESS and your player, both devices are paired automatically.

Detach the USB charging cable from the BEYERDYNAMIC AVENTHO WIRELESS after the charging process is complete.

For body-worn operation, the BEYERDYNAMIC AVENTHO WIRELESS has been tested and meets RF exposure guidelines when used with the accessories supplied or designated for this product. Use of other accessories may not ensure compliance with these guidelines.

Yes, this device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s). Operation is subject to the conditions that the device may not cause harmful interference, and the device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications made to the BEYERDYNAMIC AVENTHO WIRELESS not expressly approved by the manufacturer could void the user’s authority to operate this equipment.

The disposal symbol on the BEYERDYNAMIC AVENTHO WIRELESS, in the instructions, or on the packaging means that your electrical and electronic equipment should be disposed of at the end of its life separately from your household waste. There are separate collection systems for recycling.

Yes, all batteries are recycled to reclaim valuable material such as iron, zinc, or nickel. The separate collection and recycling of your BEYERDYNAMIC AVENTHO WIRELESS and its battery at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment.

By using the mobile application associated with the BEYERDYNAMIC AVENTHO WIRELESS, you can personalize your headphones. The app is available for Apple iOS and Android.

It is advised to follow guidelines where noise pollution at the workplace should not exceed 85 dB for a maximum of 8 hours. If the volume level on the BEYERDYNAMIC AVENTHO WIRELESS is increased by 3 dB, the permissible listening time is cut in half (e.g., at 88 dB the time is 4 hours, at 91 dB it is 2 hours).

During the charging process, the LED on the BEYERDYNAMIC AVENTHO WIRELESS flashes red.

When the LED on the BEYERDYNAMIC AVENTHO WIRELESS is permanently illuminated red, it indicates that the rechargeable battery is completely recharged.

The BEYERDYNAMIC AVENTHO WIRELESS features “L” and “R” markings to distinguish between the left and right sides.

Yes, the BEYERDYNAMIC AVENTHO WIRELESS includes a jack connection audio cable 3.5 mm for a wired connection.

Yes, the BEYERDYNAMIC AVENTHO WIRELESS transmits control signals that comply with the Bluetooth standard.

Yes, you should take the BEYERDYNAMIC AVENTHO WIRELESS to a collection point designated by local authorities. Proper disposal helps conserve natural resources and protects human health and the environment.

When the BEYERDYNAMIC AVENTHO WIRELESS is in pairing mode, the LED will rapidly flash blue and red in turns.

Before you use the BEYERDYNAMIC AVENTHO WIRELESS for the first time, you have to pair it with your mobile phone or another device with Bluetooth.

No, the pairing process for the BEYERDYNAMIC AVENTHO WIRELESS may be different with various players. Please refer to the appropriate manual of the player.

You should select “beyerdynamic Aventho wireless” under the available devices in the Bluetooth menu of your player.

If the pairing list on the BEYERDYNAMIC AVENTHO WIRELESS is full, it cannot be paired with another new player. You should clear the list to add a new player.

An acoustic signal on the BEYERDYNAMIC AVENTHO WIRELESS indicates when the achieved maximum volume has been reached.

An acoustic signal on the BEYERDYNAMIC AVENTHO WIRELESS indicates when the achieved minimum volume has been reached.

Detach the USB charging cable from the BEYERDYNAMIC AVENTHO WIRELESS after the charging process is complete.