BEKO PROFESSIONAL ADN 221C BP (01) PDF DOCUMENT

The BEKO PROFESSIONAL ADN 221C BP is an upright refrigerated display case with glass doors, designed for commercial use for cooling, displaying, and storing food and beverages.

The manufacturer guarantees reliable operation in an ambient temperature ranging from +16°C to +32°C and at a relative humidity of up to 65 percent.

Please adhere to the following safety precautions when using your BEKO PROFESSIONAL ADN 221C BP:

• Do not cover the ventilation openings located on the top and sides of the appliance.

• Do not place electrical appliances inside the food storage compartments unless they are of the type recommended by the manufacturer.

• Do not use mechanical devices or any means other than those recommended by the manufacturer to accelerate the defrosting process.

• Do not place multiple portable socket outlets or portable power supplies at the rear of the appliance.

• When positioning the appliance, ensure the power cord is not trapped or damaged.

• The appliance must be connected to a properly grounded outlet that is easily accessible.

• C-pentane is used in the insulating foam and is a flammable gas.

• After unpacking, check that the housing and power cord are not damaged. Do not use a faulty appliance.

• This appliance may be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

In the event of damage to the refrigerant circuit of your BEKO PROFESSIONAL ADN 221C BP, follow these steps:

• Do not use open flames.

• Do not use sparking devices, which means do not switch on any electrical equipment or lighting.

• Immediately ventilate the room where the appliance is located. For an appliance containing isobutane/R600a, the room must be at least 4 m³.

• A damaged power cord must be replaced by the manufacturer, a service technician, or another similarly qualified person to avoid hazards.

• Do not use adapter plugs, multi-socket outlets, or two-wire extension cords.

• The frequency and power of your electrical supply must match the parameters on the appliance’s rating plate.

• Ensure the power plug is not pressed against the back wall or otherwise damaged, as a damaged plug can cause a fire.

• Do not open the LED light cover. If the LED lighting is damaged and needs replacement, contact a service technician.

• Always disconnect the appliance from the mains for cleaning or moving. When reconnecting, wait at least 15 minutes before switching it on again.

Yes, there are restrictions for the BEKO PROFESSIONAL ADN 221C BP:

• The appliance is not designed for storing explosive substances, such as aerosol cans with a flammable propellant. Storing gasoline or other flammable liquids in the unit is forbidden.

• Do not place switched-on electrical appliances (e.g., microwave ovens, hair dryers, irons, electric kettles) on top of the refrigerator.

• Do not place containers with liquids or flowers in vases on the unit.

The BEKO PROFESSIONAL ADN 221C BP must be transported only in an upright position. The manufacturer is not liable for damage resulting from non-compliance with transport conditions.

If the appliance was tilted more than 30° during transport, you must leave it in an upright position for at least 4 hours before plugging it in to avoid damaging the compressor.

For proper installation of your BEKO PROFESSIONAL ADN 221C BP, please follow these guidelines:

• Place the refrigerator in a dry and well-ventilated room.

• Do not operate the refrigerator in an unheated room or on a balcony.

• Position the unit away from heat sources such as cookers, heaters, and direct sunlight. It should not come into contact with heating, gas, or water pipes, and should not be placed next to other electrical appliances.

• Do not cover the ventilation opening at the top of the refrigerator. Ensure there is good air circulation around the unit. Leave at least 10 cm of free space between the top of the refrigerator and any furniture above it.

• If placing the unit in a corner, leave a gap of at least 1 cm between the housing and the walls.

• The refrigerator must stand on a level surface. If needed, adjust the height by turning the feet. Doors on a slightly rear-tilted unit will close automatically.

It is recommended to have a second person assist with preparation. Follow these steps:

1. Remove all packaging. Remove the refrigerator from the styrofoam pallet. Open the door and remove any spacers.

2. When positioning, moving, or lifting the unit, do not grab the door handles, pull on the condenser at the back, or touch the compressor unit.

3. Take the two brackets out of the bag and screw them into the marked holes on the back of the appliance.

4. Take the cover out of the bag and place it on the grid located under the door.

5. Remove the plug and power cord from the water tray located under the compressor. This is its transport position. When the appliance is running, the power cord must not be in the water tray.

6. After positioning the appliance, wait approximately 30 minutes before plugging it into the mains.

The main components of the BEKO PROFESSIONAL ADN 221C BP are:

1. Fan switch

2. Thermostat knob

3. Light switch (ON/OFF)

4. Fan (turns off when the door is opened)

5. Thermometer

6. Shelves

7. Interior lighting

8. Tray for defrost water

9. Promotional canopy

The temperature inside the BEKO PROFESSIONAL ADN 221C BP is regulated using the thermostat knob. Turn the knob clockwise to lower the temperature.

The settings are marked with numbers from “0” to “5”, which do not correspond to specific temperatures but indicate cooling levels:

• 0: Compressor is off. WARNING: The power is not disconnected.

• 1: Highest temperature (minimum cooling).

• 5: Lowest temperature (maximum cooling).

The internal temperature can vary depending on the ambient temperature, the amount and temperature of the products stored inside, and how often the door is opened. In a cold room, the refrigerator cools less, which may cause the internal temperature to rise. In this case, set the thermostat knob to a setting for a lower temperature.

The BEKO PROFESSIONAL ADN 221C BP defrosts automatically. Frost that forms on the rear wall of the compartment melts during the compressor’s off-cycles. The resulting water flows down a drain channel into a collection tray above the compressor, where it then evaporates.

The BEKO PROFESSIONAL ADN 221C BP should be cleaned regularly. Before any cleaning, you must unplug the appliance from the power socket.

• Interior: Protect internal surfaces and plastic parts from fats, acids, and sauces. If a spill occurs, wash the area immediately with warm water and soap or dishwashing liquid, then wipe dry.

• Door Seal: Clean the door seal regularly and wipe it dry.

• Drain Hole: Regularly clean the water drain hole using the special cleaning tool provided.

• Exterior and Compressor: At least once a year, remove dust from the rear of the unit and the compressor using a soft brush, electrostatic cloth, or a vacuum cleaner.

• Glass Door: Clean the outer glass surface of the door with detergents intended for washing windows.

• Cleaning Agents: Do NOT use cleaning agents containing abrasive materials, acids, alcohol, or benzene. Do NOT use cloths or sponges with an abrasive layer.

If the BEKO PROFESSIONAL ADN 221C BP will be switched off for an extended period, you should leave the door open to prevent odors from developing.

To change the door opening direction of the BEKO PROFESSIONAL ADN 221C BP, it is recommended to have a helper. Before you begin, gather the necessary tools: two flat wrenches (No. 8 and No. 10) and a Phillips screwdriver.

WARNING: Before starting, switch off the appliance and unplug it from the electrical socket.

During the process, do not lay the appliance in a horizontal position.

If your BEKO PROFESSIONAL ADN 221C BP is plugged in but does not work and the voltage indicator is not lit, please check the following:

• Verify that the electrical installation in your building is working correctly.

• Ensure that the power cord is properly plugged into the socket.

If the BEKO PROFESSIONAL ADN 221C BP is operating too loudly, check these potential causes:

• Ensure the refrigerator is stable and standing on a level surface. Adjust the front feet to level the unit if necessary.

• Check that the refrigerator is not touching furniture or that parts of the cooling system at the rear are not touching the wall. Move the unit away from furniture or the wall.

• Make sure that bottles, cans, or other containers inside the refrigerator are not touching each other, which can cause rattling noises.

If you find water collecting at the bottom of the compartment, the defrost water drain hole is likely clogged. Use the provided cleaning tool to clear the obstruction from the drain hole.

Water collecting under the BEKO PROFESSIONAL ADN 221C BP usually means that the water collection tray has slipped off the compressor. Locate the tray and place it back securely on the compressor.

If the rubber door seal comes off when you open the door, it is likely dirty with sticky food products like grease or syrup. To fix this, clean the sealing tape and the grooves with warm, soapy water or dishwashing liquid. Wipe them dry, and then put the sealing tape back in its place.

If the temperature inside the BEKO PROFESSIONAL ADN 221C BP is too high and the compressor’s operating breaks are too short, check the following:

• Ensure the door is closed properly.

• Check if the door was left open for longer than necessary when accessing products.

• Consider if a large number of warm food products were recently placed inside.

Dew forming on the surface of the BEKO PROFESSIONAL ADN 221C BP indicates that the relative humidity in the room is exceeding 65%. You should ventilate the room and, if possible, remove the source of the excess humidity.