BAUHN ATV70UHDT-1022 (01) PDF Document

Unless you are wall-mounting the BAUHN ATV70UHDT-1022, you will need to attach its stands.

Step 1. Lay the BAUHN ATV70UHDT-1022 face-down on a soft, flat surface (like a sofa or a towel on a table) that is larger than the device itself.

Step 2. Match the stands to the installation points on the underside of the BAUHN ATV70UHDT-1022.

Step 3. Attach the stands to the BAUHN ATV70UHDT-1022 at the installation points using the screws provided. Do not apply excessive force, as you might damage the screw holes.

The BAUHN ATV70UHDT-1022 has holes on the back panel for use with VESA mounting brackets. The bracket is not included.

To mount it, use four standard M8x12mm screws, or longer depending on the specific bracket. Please note that the screws provided in the original package are for securing the stand only and should not be used for wall-mounting.

Insert two AAA size batteries into the remote control compartment, ensuring they are aligned with the polarity markings (+/-) shown inside. Make sure they are properly pushed into place.

When you turn the BAUHN ATV70UHDT-1022 on for the first time, the remote should pair automatically. If it does not pair, point the remote towards the sensor on the BAUHN ATV70UHDT-1022 and simultaneously press the Return and Play/Pause buttons for 3 seconds.

To use voice commands, press and hold the microphone button on the remote, speak your command, and then release the button. The BAUHN ATV70UHDT-1022 must be connected to the internet to use this feature. Additionally, you must agree to the Smart Hub Terms of Use, the guidance regarding the collection of personal information for Smart Hub, and consent to the collection of information for the voice interaction-based service.

For a wired connection, plug an ethernet cable into the LAN port on the BAUHN ATV70UHDT-1022, and it will automatically connect. For a wireless connection, open Network Settings, select Wireless, and choose your network from the list of scanned networks. Enter your Wi-Fi password using the on-screen keyboard and select ENTER to connect.

You can use Smart View to watch your smartphone screen on the BAUHN ATV70UHDT-1022. Press the Home button on the remote, navigate to Source, select Connection Guide, then choose Smartphone, and follow the steps for Screen Sharing (Smart View).

Plug the keyboard or mouse into the USB port on the back of the BAUHN ATV70UHDT-1022. To configure, press the Home button, go to Settings, then General, External Device Manager, and Input Device Manager. Note that a mouse can only be used within the Internet app.

The following table outlines the keyboard controls for the BAUHN ATV70UHDT-1022:

To manage your apps, go to the Apps screen and select Settings in the top right corner. From here, you can choose to delete an app, add an app to the Home screen, lock or unlock an app (requires a PIN), move an app, reinstall an app, or view detailed app information.

To set the clock automatically, navigate to Settings, General, System Manager, Time, Clock, Clock Mode, and select Auto. You can also adjust the time zone or Daylight Savings Time settings from the same Time menu when in Auto mode.

To set the clock manually, set the Clock Mode to Manual, and then you can directly enter the date and time using the directional buttons on the remote.

To update the software, navigate to Settings, Support, and Software Update. For manual updates via the internet, select Update Now. For automatic updates, enable the Auto Update feature in the Software Update menu. Do not turn off the power until the update is complete, as the BAUHN ATV70UHDT-1022 will restart automatically when finished.

Navigate to Settings, General, and select Reset. You will be prompted to enter your security PIN. Once confirmed, the BAUHN ATV70UHDT-1022 will restart and display the initial setup screen, having returned all settings to their defaults.

First, ensure the batteries are installed correctly regarding polarity. Remove any obstacles between the remote and the sensor on the BAUHN ATV70UHDT-1022. Check if the power indicator on the BAUHN ATV70UHDT-1022 blinks when you press the power button; if not, replace the batteries. Try pointing the remote directly at the sensor from a distance of 1.5 to 1.8 metres.

Ensure the power cord is securely plugged into the wall outlet and that the outlet is turned on. If using a multi-outlet power strip, plug the BAUHN ATV70UHDT-1022 power cable directly into a wall outlet to test it. Also, attempt to turn on the BAUHN ATV70UHDT-1022 using the physical power button located on the device itself.

Ensure the antenna cable is securely connected to the BAUHN ATV70UHDT-1022 and the wall outlet, and that the input source is set to DTV. If “No Signal” appears, perform an Auto Tuning via the Broadcasting menu in Settings. If channels are missing, perform a manual scan via the Expert Settings in the Broadcasting menu. Additionally, ensure the antenna is positioned correctly and away from other electronic equipment that may cause interference.