AVID POWER ACD316N (01) PDF MANUAL

AVID POWER ACD316N (01) PDF SUMMARY:

What are some important safety instructions to keep in mind when operating power tools?

Read and understand all instructions to avoid serious personal injury. Always follow basic safety precautions to reduce the risk of fire, electric shock, and personal injury when using electric tools.

---

What should I do to prepare my work area for using power tools?

Keep the work area clean and well lit to avoid accidents. Power tools should not be operated in explosive atmospheres. Keep bystanders, children, and visitors away from the work area. Protect others from debris by providing barriers or shields.

---

What are the electrical safety precautions I should take when using power tools?

Double insulated tools are equipped with a polarized plug that fits in a polarized outlet only one way; do not alter the plug. Avoid body contact with grounded surfaces to reduce the risk of electric shock. Power tools should not be exposed to rain or wet conditions. When operating a power tool outside, use outdoor extension cords marked “W-A” or “W”.

---

What personal safety measures should I consider when using power tools?

Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use the tool while tired or under the influence of drugs, alcohol, or medication. Dress properly by avoiding loose clothing or jewelry, containing long hair, and keeping hair, clothing, and gloves away from moving parts. Avoid accidental starting by ensuring the switch is off before plugging in. Remove adjusting keys before turning the tool on. Maintain proper footing and balance at all times. Use safety equipment, including eye protection, dust mask, non-skid safety shoes, hard hat, or hearing protection, as appropriate.

---

How should I use and care for power tools to ensure safety and proper functioning?

Use clamps or other means to secure and support the workpiece to a stable platform. Do not force the tool; use the correct tool for the application. Do not use the tool if the switch does not turn it on or off. Disconnect the plug from the power source before making adjustments, changing accessories, or storing the tool. Store idle tools out of reach of children and other untrained persons. Maintain tools with care, keeping accessories sharp and clean. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation. Use only accessories recommended by the manufacturer for the model.

---

What specific safety measures should I take when using battery-powered tools?

Ensure the switch is in the off position before inserting the battery pack to prevent accidents. Recharge only with the charger specified by the manufacturer. Use power tools only with specifically designed battery packs. Keep battery packs away from metal objects that can cause a short circuit. Do not use the tool in wet or damp conditions. Always wear protective safety equipment, including safety glasses/goggles, ear muffs, dust mask, and other protective clothing, including gloves and apron.

---

What safety instructions should I follow regarding the cordless drill/driver battery?

Never attempt to open or modify the battery for any reason. Released electrolyte is corrosive and may cause damage to eyes and skin, and it may be toxic if swallowed. If battery leakage occurs, carefully wipe the liquid off using a cloth, avoiding skin contact. In case of skin contact, immediately rinse with water; neutralize with a mild acid such as lemon juice or vinegar. In case of eye contact, rinse abundantly with clean water for at least 10 minutes. Do not expose the battery to water. Do not store in locations where the temperature may exceed 40°C (104°F). Charge at room temperature between 0°C – 45°C (0°F-140.6°F). Charge only using the charger provided with the tool. Before charging, make sure that the battery is dry and clean, and use only the battery supplied with the tool. Exercise care in handling and storing batteries to avoid shorting them with conductive materials. Do not dispose of the battery in fire; it may explode. Follow instructions and regulations given by local authorities concerning environmental protection.

---

What safety instructions should I follow regarding the cordless drill/driver charger?

Use the charger only to charge batteries supplied with the tool. Other batteries could burst, causing personal injury and damage. Never attempt to charge a non-rechargeable battery. Have defective cords replaced immediately. Do not expose the charger to water. Do not open the charger. Use indoors only; do not recharge the battery in rain or in wet conditions.

---

What are the specifications of the ACD316 cordless drill/driver?

The voltage is 20V, the charge time is 3-5 hours, and the battery capacity is 1.5Ah. It has a 3/8"(10mm) keyless chuck, an adjustable torque setting of 15+1, and a no-load speed of 0-550RPM. It includes 5pcs drill bits for wood and 5pcs HSS drill bits for metal.

---

What are the components of the cordless drill/driver?

The components include a keyless chuck, double-end driver bit storage, torque regulation ring, torque adjustment collar, LED work light, forward/reverse control button, trigger switch, rubber-covered handle, Avid Power 20V battery, and battery release button.

---

What is included in the package of the cordless drill/driver?

The package includes a battery charger, extended bar, 10pcs driver bits, flexible shaft, and 10pcs drill bits.

---

How does the variable speed trigger switch work?

The trigger switch, located similarly to a pistol trigger, starts the drill. It features variable speed, meaning the harder you squeeze, the faster the electric motor spins the drive shaft.

---

How do I use the forward/reverse control button?

The drill has a forward and reverse control, which is a sliding switch that changes the direction of the drill depending on which way it is pressed. Arrows on each side of the switch indicate the direction. The first time the tool is run after changing the direction of rotation, a click may be heard, which is normal.

---

How do I adjust the torque on the drill?

The drill has an adjustable torque collar with numbers from 1 to 15 to set the clutch to deliver a torque range. The higher the number, the higher the torque and the larger the fastener that can be driven. Rotate the collar until the desired number aligns with the arrow.

---

How do I use the keyless chuck to install or remove a drill bit?

The chuck holds the bit in place with three jaws that open or close depending on the direction you rotate the sleeve of the chuck. Place the bit in the center of the chuck’s jaws when installing a new bit.

---

How does the LED work light function?

The work light is activated when the trigger switch is depressed and automatically turns off 20 seconds after the trigger switch is released. The work light is for lighting the immediate work surface and is not intended to be used as a flashlight.

---

What should I consider regarding compatible accessories for the drill?

The drill is compatible with accessories from other brands. The drill chuck is 3/8 inch, so the diameter of drill bits/driver bits purchased cannot exceed 3/8 inch.

---

What should I do before the first use of the drill?

The battery is not fully charged, so it should be charged for 3-5 hours before the first use. Normal charging time is 3-5 hours when the battery is completely dead.

---

What should I do when the tool performance begins to diminish?

Replace a new battery when tool performance begins to diminish. Severe heat is most destructive to a battery. Never over-discharge a battery when using the tool. When tool performance begins to diminish, stop letting the tool work and recharge the battery for optimal performance.

---

How do I charge the battery pack?

When the charger is connected to AC household current, the green light is on, indicating power. When the battery is properly inserted into the charger and charging, the red light is on, indicating charging.

---

How do I know when the battery is fully charged?

Normal charging time is 3 to 5 hours when the battery is completely dead. The red light will turn off and the green light remains lit once the battery is fully charged. After the charging is completed, remove the battery pack from the charging stand immediately. When charging more than one battery pack, allow 15 minutes between charges. After many charge/discharge cycles, the battery may lose its ability to hold a charge, and should be replaced and disposed of at an appropriate waste disposal facility.

---

How do I use the USB output for charging other devices?

Plug the USB cable into the USB Output Port on the battery pack. Press the button for charging. Press the button to display the battery level. Three lights on the battery indicate a full charge, two lights show 50% of the power, while one light shows 25%. Remove the charger from the battery before checking the battery level.

---

How do I install or remove the battery pack?

Ensure the lock-off button is engaged to prevent switch actuation before removing or installing the battery. To install, slide the battery pack into the bottom of the tool until a click is heard, ensuring the latch is in place and the battery is secure before operation. To remove, press the battery release latch and pull the battery pack out at the same time.

---

How do I install or remove a drill/driver bit using Method 1?

To install, rotate the chuck anticlockwise by hand to open the chuck jaws. Place the driver/drill bit in the chuck as far as it will go. Then rotate the chuck clockwise by hand to tighten the chuck jaws. To remove, do it in reverse.

---

How do I install or remove a drill/driver bit using Method 2?

To install, move the Forward/Reverse Button to the right side of the tool to make it do reverse rotation to open the chuck jaws. Hold the keyless chuck with one hand and squeeze the trigger with the other hand to open the chuck jaws. Carefully center the driver bit/drill bit between the jaws. Move the Forward/Reverse Button to the left side for forward rotation. Hold the keyless chuck with one hand and squeeze the trigger slowly until it is locked in place. To remove, do it in reverse.

---

How do I install or remove the extended bar?

Insert the driver bit (driver bits only) into the head of the extension rod (there is a magnet inside). Open the chuck jaws and insert the black end of the extension rod into the chuck, referring to the drill/driver bits installation steps.

---

How do I install the flexible shaft?

Open the chuck jaws and insert the extended bar into the chuck jaws, hold the flexible shaft with one hand, insert the extended bar into the extended bar with the other hand. Install the driver bit into the other end of the extended bar. Hand tighten the sleeve at the end to confirm that the bit is secure.

---

What are the steps for drilling?

If drilling thin material, use a wood “back-up” block to prevent damage to the material. Install the drill bits needed, referring to the drill/driver bits installation steps. Turn the collar ring to adjust the torque; the higher the number, the more torque the drill will apply. Always apply pressure in a straight line with the bit. Use enough pressure to keep the drill biting, but do not push hard enough to stall the motor or deflect the bit. Hold the tool firmly with one hand on the grip and the other hand on the bottom of the battery cartridge to control the twisting action. Squeeze the trigger slowly and then increase the speed. Release the switch trigger as soon as drilling the depth needed. If overloaded, the drill may stop suddenly.

---

What are the steps for screwdriving?

Install the driver bits needed, referring to the drill/driver bits installation steps. To tighten the screws, depress the reverse control button on the left side of the tool. Squeeze the trigger slowly, and the screws come out. To loosen the screws, depress the forward control button on the right side of the tool, slowly press on the trigger until the screws is locked in place.

---

How do I maintain the tool?

Keep the tool clean using a soft damp (not wet) cloth. Do not use solvents on the plastic parts. Lubrication is not necessary. After long use, have an authorized service center maintain and lubricate the tool. To maintain the best performance of the rechargeable battery, prevent it from overheating and overcharging.

---

What are the notice regarding repairs?

Repairs should be made by an authorized repair center. Opening the tool could invalidate the warranty. Due to continuous product improvement, the product specification may change without prior notice.