AUDIOVOX PURSUIT PRO-9276N (01) PDF Document

If the transmitter button is pressed more than fifty times while out of range, it may need re-alignment. To do this, simply press the lock/unlock button two times within a one-second time period. The system will now respond to that transmitter each time a button is pressed.

To lock your vehicle, exit the vehicle, close all doors, hood and trunk, then simply press the lock button of your keychain transmitter. The parking lights will flash once when the doors are locked.

To unlock your vehicle, simply press the unlock button of your keychain transmitter. The parking lights will flash twice when the doors are unlocked.

Holding the lock/unlock transmitter button for 3 seconds will activate the car finder mode causing the parking lights to flash and the optional horn to beep for 30 seconds or until the button is activated again for 3 seconds or any other button is operated.

To activate the optional accessory, press and hold the trunk/key button on the keychain transmitter for four seconds.

To activate the optional accessory for Channels 4, 5, 6, or 7, press the option button on the keychain transmitter. The optional accessory will immediately engage.

The pushbutton LED control switch allows you to temporarily disable the remote starting function. To place the system in service mode:

1) With the system disarmed/unlocked, and the ignition switch off Press and Hold the PRLED on.

2) Turn the ignition switch on, off, on, off, on, off.

3) The LED begins to flash two short flashes followed by one long flashes and continues this pattern until returned to normal mode of operation.

To Exit R/S Override Mode:

1) With the system disarmed, Press and Hold the PRLED on.

2) Turn the ignition switch on, off, on, off, on, off.

3) The LED turns off indicating that the R/S unit is fully functional once again.

Anytime the engine is running for more than 15 seconds:

1) Place the gear selector in park.

2) Set the parking, (hand), brake.

3) Be certain your foot is off the brake pedal.

4) Press the program/Push-Button switch 2 times within 5 seconds.

The parking lights will flash two times indicating the mode was successfully entered.

With the turbo timer mode selected on, after you’ve arrived at your destination, while the engine is still running, set the parking brake, pause 2 seconds, then turn the ignition switch to the off position. The engine will continue to run the allotted time according to the selection during installation.

If you do not want the vehicle to continue to run for one cycle, simply step on the vehicle’s brake, or release the parking brake, or activate the transmitter’s start button two times in succession. Any of these will cause the engine to turn off.

The system WILL NOT start the vehicle if any one of the following conditions exists:

1. The Vehicle Hood Is Opened.

2. The Gear Selector Is In Any Gear Other Then Park.

3. The Brake Is Depressed.

4. The System is in the Remote Start Override mode.

Press and release the trunk/key button of your keychain transmitter two times within 2 seconds. The vehicle will start and remain running for the pre-programmed 5, 10, 15 or 20 minutes.

When you arrive at your vehicle, unlock it with the key or by pressing and releasing the trunk/key button of your keychain transmitter. Enter the vehicle and turn the ignition key to the on position.

CAUTION! Do not turn the key to the start position. This will cause the starter motor to engage with the already running engine which could result in damage. Step on the brake pedal to disengage the remote start unit. The vehicle will continue to run but now on it’s own power.

The engine will stop running if you complete any of the following:

1. Press and release the trunk/key button of your keychain transmitter two times within 2 seconds.

2. Depress the brake pedal.

3. Open the hood.

4. Place the system in the Remote Start Override mode.

5. Race the engine to above 4000 RPM.

1. Turn the ignition key on then off.

2. Within 10 seconds, activate the RF start command two times. (Push the second channel button of your keychain transmitter 4 times).

The parking lights will flash 4 times indicating the timed start mode is activated. The vehicle, on a 2 or 4 hour interval basis, will automatically start, run for the pre-programmed time, and then shut off. This will continue for 48 hours.

Alternatively, the automatic start up timer can be initiated from the keychain transmitter:

1. Start the vehicle using the keychain transmitter by pressing and releasing the trunk/key button transmitter button 2 times.

2. Shut off the vehicle using the keychain transmitter by pressing and releasing the trunk/key transmitter button 2 times.

3. Within 10 seconds of step 2, activate the RF start command two times. (Push the trunk/key button of your keychain transmitter 4 times).

To cancel the automatic start up timer do one of the following;

1. Start the vehicle manually with the use of the ignition key and depress the brake pedal.

2. Remote start the vehicle using your keychain RF transmitter.

3. Shut off the vehicle using the keychain transmitter by pressing and releasing the trunk/key transmitter button 2 times.