ASUS TUF FX504G (01) PDF Document

Please note the following about your ASUS TUF FX504G:

• The keyboard’s layout may vary per region or country. The Notebook view may also vary in appearance depending on the Notebook PC model.

• Closing the lid when the system is under high load forces your Notebook PC to go into sleep mode to prevent overheating.

The components on the top view of your ASUS TUF FX504G are:

• Array microphones (on selected models)

• Microphone

• Camera indicator

• Camera

• Display panel

• Capital lock indicator

• Air vents

• Status indicators

• Power button

• Power indicator

• Numeric keypad

• Touchpad

• Keyboard

The I/O ports and slots on your ASUS TUF FX504G include:

• Kensington® security slot

• Power (DC) input port

• LAN port

• HDMI port

• USB 2.0 port

• USB 3.1 Gen 1 port

• Headphone/Headset/Microphone jack

Follow these steps to get started with your ASUS TUF FX504G:

1. Charge your Notebook PC

A. Connect the AC power cord to the AC/DC adapter.

B. Connect the DC power connector into your Notebook PC’s power (DC) input port.

C. Plug the AC power adapter into a 100V~240V power source.

IMPORTANT! Use only the bundled power adapter to charge the battery pack and supply power to your Notebook PC.

NOTE: The power adapter may vary in appearance, depending on models and your region.

Charge the Notebook PC for 3 hours before using it in battery mode for the first time.

2. Lift to open the display panel

3. Press the power button

WARNING! The bottom of the Notebook PC can get warm to hot while in use or while charging the battery pack. When working on your Notebook PC, do not place it on surfaces that can block the vents.

CAUTION!

• This Notebook PC should only be used in environments with ambient temperatures between 5°C (41°F) and 35°C (95°F).

• Refer to the rating label on the bottom of your Notebook PC and ensure that your power adapter complies with this rating.

• The power adapter may become warm to hot while in use. Do not cover the adapter and keep it away from your body while it is connected to a power source.

IMPORTANT!

• Ensure that your Notebook PC is connected to a grounded power adapter before turning it on for the first time.

• When using your Notebook PC on power adapter mode, the socket outlet must be near to the unit and easily accessible.

• Locate the input/output rating label on your Notebook PC and ensure that it matches the input/output rating information on your power adapter. Some Notebook PC models may have multiple rating output currents based on the available SKU.

Power adapter information:

– Input voltage: 100-240Vac

– Input frequency: 50-60Hz

– Rating output current: 7.7A (150W)

– Rating output voltage: 19.5V

WARNING! Read the following precautions for your Notebook PC’s battery:

• Only ASUS-authorized technicians should remove the battery inside the device (for non-removable battery only).

• The battery used in this device may present a risk of fire or chemical burn if removed or disassembled.

• Follow the warning labels for your personal safety.

• Risk of explosion if battery is replaced by an incorrect type.

• Do not dispose of in fire.

• Never attempt to short-circuit your Notebook PC’s battery.

• Never attempt to disassemble and reassemble the battery (for non-removable battery only).

• Discontinue usage if leakage is found.

• This battery and its components must be recycled or disposed of properly.

• Keep the battery and other small components away from children.

• DO NOT use the Notebook PC near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.

• DO NOT use the Notebook PC during an electrical storm. There may be a remote risk of electric shock from lightning.

• DO NOT use the Notebook PC in the vicinity of a gas leak.

• DO NOT dispose the Notebook PC battery pack in a fire, as they may explode. Check with local codes for possible special disposal instructions to reduce the risk of injury to persons due to fire or explosion.

• DO NOT use power adapters or batteries from other devices to reduce the risk of injury to persons due to fire or explosion. Use only UL certified power adapters or batteries supplied by the manufacturer or authorized retailers.

IMPORTANT! To provide electrical insulation and maintain electrical safety, a coating is applied to insulate the device except on the areas where the I/O ports are located.

Products with electrical current ratings up to 6A and weighing more than 3Kg must use approved power cords greater than or equal to: H05VV-F, 3G, 0.75mm² or H05VV-F, 2G, 0.75mm².

To prevent possible hearing damage, do not listen at high volume levels for long periods.

WARNING! Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. “The manufacture declares that this device is limited to Channels 1 through 11 in the 2.4GHz frequency by specified firmware controlled in the USA.”

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure compliance requirements, please avoid direct contact to the transmitting antenna during transmitting. End users must follow the specific operating instructions for satisfying RF exposure compliance.

Yes, the WiFi operating in the band 5150-5350 MHz shall be restricted to indoor use for countries listed in the table below:

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.