ANKO JLR-80036 (01) PDF Document

The ANKO JLR-80036 comes with the following accessories:

> 1 x Magnetic foldable selfie light

> 4 x Magnetic ring

> 1 x Tripod stand

> 1 x Mobile phone photography magnetic holder

> 1 x Magnetic camera handle bracket

> 2 x Charge cable

> 1 x User manual

Please read all safety instruction warnings carefully before using this product. Improper use of this product may result in damage. To ensure the product works well, please never use this in the following conditions:

1. Moist or underwater conditions.

2. Do not position near a heat source or something that operates at a high temperature.

3. Conditions with direct and strong sunlight.

4. Do not use chemical solvents when cleaning this product.

5. This product shall be supplied by a 5V DC 1A power source (not included).

6. This product contains small parts, keep away from children under 3 years.

Magnetic foldable selfie light:

Product Size: 60*15mm

Battery capacity: 300mAh

Color Temperature:

White: 10000-14000K

Warm: 2900-3100K

Mixed white-warm: 2900-14000K

Working Time: 0.5-1.5 hours

Charging Time: around 1.5 hours

Bluetooth controller on magnetic camera handle bracket:

Battery capacity: 90mAh

Working Time: around 40 hours

Charging Time: around 1 hour

1. Remove the magnetic ring’s tape.

2. Paste the magnetic ring separately on the phone case / the backplane of the Magnetic camera handle bracket / the back of the magnetic holder.

Note: The magnetic ring should not be attached directly to the mobile phone, as it is very difficult to remove once pasted. Please stick it only to the phone case.

3. Attach the magnetic holder to the tripod stand by screwing its threaded hole onto the tripod’s mounting screw. Then, adjust the tripod to a stable angle for use.

4. Mount the light on the back of the holder.

5. Combine the magnetic holder and the camera handle bracket.

6. Place the mobile phone onto the magnetic part of the camera handle bracket, then rotate the selfie light upward to complete the assembly.

1. Power Switch

– Turn the switch to the ON position to activate the light. Turn the switch to the OFF position to turn the light off.

2. Light Mode Switch

– Touch the switch to turn on the light, short press to switch between 3 color modes: White, Warm, Mixed (white-warm).

– Long press the switch to gradually increase or decrease the light brightness.

Notes:

a. With constant power on, the light mode and the light brightness will be remembered and restored by the next light on.

b. Please turn off the light when not in use.

1. Take the Bluetooth controller off the handle bracket.

2. Long press the Power Switch and the blue indicator light flashes.

3. Turn on the Bluetooth and search for the Bluetooth name “Anko43559343”. Once connected, the blue light will be off.

4. Open the connected camera, short press the power switch:

– In camera mode, it will take pictures.

– In video recording mode, it will start recording. (Short press again to stop recording.)

5. Long press the Power Switch to turn off the controller when not in use. Always place the controller back into the slot securely to prevent loss.

The supplied USB charging cables should be inserted into a standard USB power source rated at 5V DC 1A specification.

Selfie light:

The indicator will keep lighting in red during charging and turns blue after fully charged.

Bluetooth controller on camera handle bracket:

The indicator will keep lighting in red during charging and turns off after fully charged.

Note: If the battery is low/totally run out, the product will not work at all, please charge before use.

› Battery cannot be subjected to high or low extreme temperatures, low air pressure at high altitude during use, storage or transportation.

› Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.

› Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.

› A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.

You can use this product in a full assembly or separately with the following combinations:

a. Use the selfie light and the mobile phone together.

b. Use the camera handle bracket and the mobile phone together.

c. Combine to use the selfie light, camera handle bracket and mobile phone.

d. Combine to use the selfie light, tripod stand, photography magnetic holder and mobile phone.