ANKO 42976707 (01) PDF Document

The controls and features are the same for both earbuds. Use the Function Button for the following actions:

Double-click: Play, pause, answer, hang up, pick up.

Three strikes to the right or left: Reject a call.

Three strikes to the right or left: Next Track / Previous track.

Hold down for 2 seconds: Activate Siri.

Long press 3 seconds: Power on.

Long press 5 seconds: Power off.

NOTE: Each earbud must be powered on separately. Once they are linked, powering off one earbud will power off both.

Earbud Indicator LED:

• Red when charging.

• White when fully charged. It goes out in a minute.

Charger Power & Battery Indicator LED:

• Flashing white when the case is charging.

• Solid white when the case is ON.

• Individual LEDs show the battery level.

For best results, charge the case fully before use. The charging time is approximately 2 hours.

Using a TYPE-C to USB cable, connect the case to the USB port of a powered-on computer or a USB power adaptor (not included) to charge the case.

For best results, charge the earbuds fully before use. Charging time is approximately 2 hours.

1. Open the cover and place the earbuds in their docking stations, noting the Left and Right placement.

2. Close the case to ensure the contact between the earbuds and the case.

3. Use the Power switch on the case to power it ON and begin charging the earbuds.

• While charging, the indicator on the earbuds will turn red.

• When charging is complete, the indicator will turn white. After 1 minute, the indicator and the case will power off.

Linking Earbuds:

The earbuds feature automatic linking and will connect to each other after powering on.

• Take the headset out of the charging case and it will automatically pair up. The LEDs on both earbuds will quickly flash red and white as the connection is made.

• When successfully linked, a voice will announce the connection, and the right earbud LED will flash red and white, while the left one slowly flashes white.

Pairing Bluetooth:

1. With the earbuds linked, you can now connect to your Bluetooth device. The LED indicator on the right earbud will continue flashing white and red, indicating it is ready to pair to a Bluetooth device.

2. On your Bluetooth device, access Bluetooth Settings and search for nearby devices. Select anko TWS when it is discovered. When successfully connected to your Bluetooth device, a voice prompt will announce the Bluetooth connection and the LED indicator on both earbuds will blink white once every 5 seconds.

3. Audio played through the connected Bluetooth device will now be heard through both earbuds.

When disconnected, follow the below step to re-sync:

1. Turn off your Bluetooth device.

2. Place both anko TWS earphone in your charging case. Close the lid and wait 30 seconds, then open it.

3. The TWS will auto re-sync the left and right side.

Yes, you can power on a single earbud to use alone, and it will function in Mono sound mode.

• Double – Click: Play, pause, answer, hang up.

• Reject: Three strikes to the right or left.

• Track selection: Click three times on the left to play the previous song, and click three times on the right to play the next song.

• Hold down for 2 seconds: Pick up Siri.

• You can also use the controls on the connected phone to handle audio functions.

• Double – Click: Play, pause, answer, hang up.

• Reject: Three strikes to the right or left.

• You can also use the controls on the connected phone to handle phone functions.

While the case power is ON, placing the earbuds in the charging case will automatically power them off and begin charging.

• Operating temperature: 0-45°C.

• This BT earbuds shall be charged by the supplied charging unit only.

• Battery cannot be subjected to high or low extreme temperatures, low air pressure at high altitude during use, storage or transportation.

• Replacement of a battery with an incorrect type that can result in an explosion or the leakage of flammable liquid or gas.

• Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.

• Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.

• A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.