Free English ALLIANCE AWN43RSN305XW01 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD ALLIANCE AWN43RSN305XW01 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
How do I enter the Factory Test Procedure on the ALLIANCE AWN43RSN305XW01?
To enter the Factory Test Procedure for the ALLIANCE AWN43RSN305XW01, follow these steps:
1. Disconnect electrical power from the unit.
2. Reconnect electrical power to the unit.
3. Wait about 10 seconds.
4. Turn the Cycle Selection knob to the opposite of Normal Eco. Stay on that selection for at least one second.
5. Press and hold the Start/Pause button.
6. Change the Cycle Selection knob to Normal Eco within 5 seconds or the Start press will be invalid.
7. Stay on Normal Eco for at least one second. The control will enter Factory Test Mode.
8. To advance through the sequence of test steps, press the Start/Pause button.
What steps are performed during the Factory Test Procedure on the ALLIANCE AWN43RSN305XW01?
The Factory Test Procedure for the ALLIANCE AWN43RSN305XW01 includes several steps as detailed in the following table:
| Number | Display (LEDs lit) | Motor | Valves | Lid | Pump | Exit | Step |
|---|---|---|---|---|---|---|---|
| 0 | All LEDs lit | Off | None | Unlocked | Off | 1 | Show Mode |
| 1 | Refer to Cycle Switch Test | Off | None | Unlocked | Off | 3 and then 1 | Cycle Switch |
| 2 | Refer to Temperature Switch Test | Off | None | Unlocked | Off | 3 and then 1 | Temperature Switch |
| 3 | Refer to Load Size Switch Test | Off | None | Unlocked | Off | 3 and then 1 | Load Size Switch |
| 4 | Refer to Extra Rinse Test | Off | None | Unlocked | Off | 3 and then 1 | Extra Rinse |
| 5 | Refer to Lid Switch Test | Off | None | Unlocked | Off | 10 and then 1 | Lid Switch |
| 6 | Wash | Off | Hot | Unlocked | Off | 1 | Hot Fill |
| 7 | Rinse | Off | Cold | Unlocked | Off | 1 | Cold Fill |
| 8 | Wash, Rinse | Off | Hot, Cold | Unlocked | Off | 2 and then 1 | Pressure Sensor Fill |
| 9 | Lid Lock | Off | None | Locked | Off | 7 and then 1 | Lid Lock Check |
| 10 | Wash, Spin | Delicate Long Stroke Agitate | Cycle Output | Locked | Off | 1 | Long Stroke Agitate |
| 11 | Rinse, Spin | Delicate Short Stroke Regular Agitate | None | Locked | Off | 1 | Short Stroke Agitate |
| 12 | Refer to Factory Spin Test | Factory Spin Profile | None | Locked | On | 1 | Factory Spin |
| 13 | Wash, Rinse always on | Off | None | Unlocked | Off | 14 and then 1 | Unbalance Switch Test |
| 14 | Rinse, Spin and Lid Lock when lid locked | Off | Hot, Cold, Cycle output | Unlocked | On | 1 and then 4 | Breakaway |
| 15 | None | Off | None | Unlocked | Off | 13 | Power Down |
How can I test the mixing valve solenoids on the ALLIANCE AWN43RSN305XW01?
Test the mixing valve solenoids on the ALLIANCE AWN43RSN305XW01 using an Ohm meter based on the following resistance values. Note that readings slightly out of range may be due to meter conditions and do not necessarily indicate failure.
| Valve Type | Resistance |
|---|---|
| 120 Volt valves | 900 to 1100 Ohms |
| 240 Volt valves | 3200 to 4000 Ohms |
How do I level the ALLIANCE AWN43RSN305XW01?
To level the ALLIANCE AWN43RSN305XW01, follow these steps:
1. Place a level on the cabinet top and check if the washer is level from side to side and front to back.
2. If the washer is not level, tilt the washer back to access the front leveling legs. Loosen the locknuts and adjust the legs by screwing them into or out of the washer base.
3. Once adjusted, tilt the washer forward on the front legs and lower it back down into position to set the rear self-leveling legs.
4. The washer must not rock. When the washer is level and does not rock, tighten the locknuts securely against the bottom of the washer base. If these locknuts are not tight, the washer will not remain stationary during operation.
What are the torque specifications for the drive bell on the ALLIANCE AWN43RSN305XW01?
When replacing or reinstalling the drive bell on the ALLIANCE AWN43RSN305XW01, torque the bolts to these specifications:
| Location | Minimum | Maximum |
|---|---|---|
| Drive Bell to Washtub and Hub | 100 inch-pounds [11.3 Nm] | 140 inch-pounds [15.8 Nm] |
| Drive Bell to Top of Drive Shaft | 60 inch-pounds [6.78 Nm] | 100 inch-pounds [11.3 Nm] |
What should I do if the ALLIANCE AWN43RSN305XW01 does not empty water?
If the ALLIANCE AWN43RSN305XW01 does not empty, first check the drain hose for kinks. If it is kinked, straighten it. Check for excessive suds or detergent in the machine; if present, use low-sudsing high efficiency detergent. Verify if the drain hose is out of the hose retainer clip in the base of the cabinet; if so, remove the front panel and install the drain hose into the base retainer block. Check if there is proper voltage present at the pump; if not, check the wiring from the pump to the drive board. If voltage is present at the pump, replace the pump. Also, check if there is proper voltage present at the drive board; if not, replace the drive board. Verify that the pump is rated at the correct frequency (50 or 60 Hertz) and check for obstructions in the outer tub outlet hose.
How can I troubleshoot excessive vibration in the ALLIANCE AWN43RSN305XW01?
To troubleshoot excessive vibration in the ALLIANCE AWN43RSN305XW01, check the following:
1. Ensure the shipping plug has been removed from the base.
2. Ensure there is not an unbalanced load in the tub. If there is, stop the washer, redistribute the load, and restart.
3. Check if any centering springs are broken, disconnected, or in the wrong position. Ensure green springs are in the front two positions.
4. Check if the washer is unleveled. Adjust the leveling legs and make sure the rear leveling legs are free.
5. If the washer is installed on a weak, spongy, carpeted, or built-up floor, relocate the washer or support the floor to eliminate the condition.
6. Check if cabinet screws are incorrect or loose.
7. Check if the base is damaged (e.g., from being dropped).
8. Ensure there is no lubricant on the pivot dome or base friction ring; if so, remove the lubricant or replace parts.
9. Check if the partial liquid filled balance ring is leaking; if so, replace the balance ring.
10. Check if the friction ring is broken; if so, replace it.
How can I fix a water leak from the outer tub of the ALLIANCE AWN43RSN305XW01?
To address a water leak from the outer tub on the ALLIANCE AWN43RSN305XW01, inspect the following areas:
1. Check if the water seal in the outer tub is leaking; if so, replace the hub and seal kit assembly.
2. Check for a hole in the outer tub; if present, replace the outer tub.
3. Check if the pressure hose or accumulator is leaking; if so, replace the pressure hose and/or accumulator.
4. Check if the outer tub cover gasket is leaking; if so, replace the gasket.
5. Check if water is coming out of the overflow holes in the upper tub cover due to the tub leaning back or not being level; if so, level the washer.
6. Check for an obstruction in the drain causing water to come over the top of the outer tub cover; if so, remove the obstruction.
7. Check if tub cover drain holes are plugged; if so, clean them.
8. Check if the tub-to-pump hose is leaking at the clamp; if so, tighten the clamp.
Why does the ALLIANCE AWN43RSN305XW01 fail to lock the lid?
If the lid of the ALLIANCE AWN43RSN305XW01 does not lock, check the following:
1. Ensure the cycle has not been paused or canceled.
2. Check if the lid catch is broken; if so, replace it.
3. Ensure the unit is level left to right to allow for proper catch-to-lock alignment.
4. Ensure all lid bumpers are in place; if not, replace them.
5. Check if the wiring to the lid lock is broken or disconnected; repair or reconnect the harness.
6. Ensure the lock is securely attached to the mounting bezel; if not, tighten the mounting screws or replace the bezel.
7. Check if the lid lock is wet; if so, allow it to dry. If the lock is not wet, replace the lid lock.
CLICK HERE TO DOWNLOAD ALLIANCE AWN43RSN305XW01 (01) PDF DOCUMENT