Free English ABUS FUEM60000 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD ABUS FUEM60000 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What is included in the scope of delivery for the ABUS FUEM60000?
The scope of delivery for the ABUS FUEM60000 includes:
• 1x Wireless Vibration Detector
• 1x CR2 Battery
• 3x Screws
• 3x Wall Anchors
• 1x Quick Guide
How do I perform the initial setup of the ABUS FUEM60000?
This product must be installed and maintained by a qualified service engineer.
The ABUS FUEM60000 starts in Secoris-RF mode after power-up. To set up the device, follow these steps:
1. Start the teach-in process at the control panel or keypad.
2. Press the tamper button on the detector when prompted by the system.
What are the mounting requirements for the ABUS FUEM60000?
When mounting the ABUS FUEM60000, please adhere to the following important requirements:
• DO NOT mount the sensor on the moving part of the door or window.
• Mount the sensor vertically on the fixed frame.
How do I configure the jumper settings on the ABUS FUEM60000?
The jumper settings on the ABUS FUEM60000 determine the operating mode and functions. Refer to the table below for configurations.
| Function | Jumper Position | Description |
|---|---|---|
| Legacy Jumper | On “Legacy” pins | Secoris RF Mode |
| Legacy Jumper | Removed from “Legacy” pins | Secvest radio-mode |
| Reset Jumper | On “Reset” pins | Normal operation |
| Reset Jumper | Removed from “Reset” pins | Factory settings |
How do I configure the LED display on the ABUS FUEM60000?
The LED display can be activated or deactivated using a jumper. Please note that this setting is only effective if the ABUS FUEM60000 is operated in Secvest radio mode.
| LED Jumper Position | Status |
|---|---|
| On “LED” pins | LED display deactivated |
| Removed from “LED” pins | LED display activated |
How do I adjust the sensitivity of the ABUS FUEM60000?
The sensitivity of the ABUS FUEM60000 can be adjusted using the SENS potentiometer. This setting is only effective if the unit is operated in Secvest radio mode.
How do I install the ABUS FUEM60000 for use with the tamper switch?
For installation with the tamper switch active, ensure the breakaway plastic part on the back of the device casing remains intact. Do not break this plastic part.
What are the technical specifications of the ABUS FUEM60000?
| Dimensions (W x H x D) | 19 x 103 x 24 mm |
| Weight | 30g (without batteries) 40g (with batteries) |
| Displays | Displaying detection/sending (red / if activated) and displaying signal strength (green, yellow, red) |
| Operating temperature | -10 °C to +55 °C |
| Environmental class | II (EN 50131-1) |
| Humidity, max. | 0 – 95%, Non-condensing |
| Operating frequency / modulation | Secoris RF mode: 868.0 – 868.5 / G2FSK Secvest radio-mode: 868.6625 / G2FSK |
| HF transmission power | 10 mW |
| Transmission and reception range | 700m open space |
| Required Signal-Strength | The reading must be at least 3 and ideally greater than 5. |
| Sensor Type | Accelerometer |
| Low battery warning / restore level | ‘flat battery’ fault at < 2.4 V. If the voltage is below the lower threshold of 2.4 V, a fault report is sent to the alarm control panel. Low battery restore at 2.5V |
| Battery type / typical battery capacity per cell | 1 x CR2 battery, 3V / 0.85 Ah |
| Battery life | up to 2 years |
| Power consumption / energy consumption | 20 µA standby current / 25 mA max. |
| Recommended Batteries | Panasonic CR-2L/1BP (ABUS-item.: FU2990), or Duracell DLCR2, or GP CR2 |
| Security level | Grade 2 (EN 50131-1 + A1 + A2 + A3:2020) |
| Type of power supply | Type C (EN 50131-1 + A1 + A2 + A3:2020) |
| Tamper monitoring | yes |
| Standards for intrusion and Hold-up Alarm devices | The device is compliant with EN 50131-5-3:2017 at security level 2 if installed correctly together with Secvest Wireless Alarm System FUAA50xxx or BUM060030 Secoris BUS Wireless Extension. |
| EU-directives | RED: 2014/53/EU, RoHS: 2011/65/EU, ErP:2009/125/EC, General Safety: 2001/95/EC |
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
CLICK HERE TO DOWNLOAD ABUS FUEM60000 (01) PDF DOCUMENT