XGIMI Z4 AURORA (01) PDF MANUAL

Plug in electric power supply.

Slip lens cover to the end, blue indicator lights up, the device is turned on.

If the lens cover is opened while the device is turned off, press the XGIMI button which is on the middle of black disc for 3 seconds, the device will be turned on.

Press “power key” on remote-control, choose shutdown/restart/shutdown LED/shutdown timer.

Long press “XGIMI” key on the middle of the black disc for 3 seconds, to device is turned off.

Slip “fn” key on the bottom of remote-control to the right side, focusing function is turned on.

Press “volume +” and “volume -” to adjust the image definition.

Slip “fn” key on the bottom of remote-control to the left side when image definite, focusing function is turned off.

On/Off

Voice Key

Menu/Shortcut

Directions

Home

Return

Volume + (Focusing +)

Volume – (Focusing -)

Reset

Charge

Function Key

Please charge the remote-control for 30 minutes before the first time use.

Please put the remote-control within 10 cm from the device.

Press “return” and “home” at the same time, green indicator light blinks for 3 seconds, blue indicator light quickly blinks. Then release the buttons, remote control is pairing. If pairing is successful, blue indicator light flashes continuously for 2 seconds and then extinguishes. If pairing is failed, exit pairing mode after 30-seconds timeout, follow the steps above to pair again.

When the red indicator appears and blinks, please charge the remote-control.

Slip “fn” key on the bottom of remote-control to the right side, focusing function is turned on. Press “volume +” and “volume -” to adjust the image definition.

Slip “fn” key on the bottom of remote-control to the right side, gravity sensor function is turned on. Pairing with games that support gravity sensor and use remote-control horizontally. Slip “fn” key on the bottom of remote-control to the left side, gravity sensor function is turned off. When gravity sensor function is turned on, mouse function cannot be used, and blue indicator light flashes continuously.

Quickly and forcibly shake the remote-control to turn on/off the mouse function.

Short press “menu key ()” to open menu function, long press “menu key ()” to open shortcut function.

Red indicator light flashes continuously when remote-control is charging, green indicator light flashes continuously when charging is completed; red indicator light quickly blinks for 4 times when power is low; red indicator light quickly blinks for 10 times when power is very low, remote control has to be charged immediately.

Under working mode, remote-control will enter sleep condition when it is standing for more than 10 seconds, it can be awoken by pressing any button.

If remote-control’s system is crashed, press reset button, then release reset button, red indicator light will blink for 3 times, reset is completed.

Press “up” key of remote control on home page to access shortcut entry, then switchover between standard version and business version.

Alternatively, navigate to System setup > General setup > Desktop version, then switchover between standard version and business version.

Navigate to System setup > international setting, to choose your language and time zone.

For Application Search: In Aptoide App market, press the search symbol, enter the application name, and download. Use mouse function if any APP does not work with remote.

For Application update: Navigate to Aptoide > updates, to update your installed application.

For Application move/delete: Choose the App you want to change, long press “OK” key to move/uninstall/collect it.

For Keystone correction: Navigate to System setup > projection setup, press “OK” key to choose adjust point. After choosing a point, use “direction” keys to adjust keystone horizontally or vertically. After completing the adjustment, press “return” key to save adjustment and return to previous menu.

For Projection mode setup: Navigate to System setup > projection setup > projection mode setup, choose projection mode according to device placed condition.

For Stepless zooming: Navigate to System setup > projection setup > Stepless zooming, to adjust frame size and aspect ratio.

For Image adjustment: Long press “menu (=)” key for 2 seconds, release “menu” key, shortcut setting function will popup on the bottom of screen, adjust the image according to your preference.

Navigate to System setup > general > keyboard, then choose input method.

Navigate to System setup > about > device name, to choose or customize your devices name.

Navigate to System setup > About > System update, device will send update notification when system detected current version is not the latest version, press “online update” to update online.

Download USB force update patch, decompress the file and send to USB.

Connect the device to power supply, then plug USB in USB 2.0 port of the device.

Navigate to System setup > about > system update > USB update, wait for force update complete.

Alternatively, insert RESET hole with a needle, and then open the lens cover.

Wait until the system enters update interface, loosen the button and wait for update complete.

Note: please do not remove USB or power supply during updating process, please use FAT32 form USB.

Use “left” and “right” keys to adjust play progress.

When playing a video, press “menu (=)” key to choose subtitle menu to set subtitle.

When playing a video, press “menu ()” key to choose 3D setup menu and set 3D mode.

For WiFi setup: Navigate to System setup > network setup > WiFi setup, choose a network and connect with it.

For WiFi hotspot: Navigate to System setup > network setup > WiFi hotspot, turn on WIFI hotspot to let other devices find this WiFi hotspot in their WiFi setting, enter password of this hotspot and connect to XGIMI device.

For Miracast: Navigate to System setup > network setup > Miracast, turn on Miracast, mobile phone or PC that support Miracast can connect XGIMI and use it as mirroring display.

For AirPlay: Navigate to System setup > network setup > AirPlay, turn on AirPlay, mobile phone or PC that support AirPlay can connect XGIMI and use it as mirroring display.

For Bluetooth & external device: Navigate to System setup > Bluetooth & external device, pair and connect with external Bluetooth devices, e.g. speaker, remote-control, and gamepad.

For Wired setup: Navigate to System setup > network setup > wired setup, plug internet cable into the internet port which is at the back of XGIMI.

Navigate to FileManager > add device, choose the device and add remote sharing file.

In FileManager, long press “OK” key, selection box appears. Press “menu()” key to choose copy/cut/paste/delete/rename/detail.

Plug in USB, press “File Manager”, view the files of USB device, press “menu (=)” key to open more functions.

Stay on home page, press “up” key to open shortcut entry at the top of screen. Functions from left to right are switching of desktop versions/WIFI setup/Bluetooth/eject USB.

Stay on home page, press “down” key to open collection entry at the bottom of screen, users are able to add favorite Apps in collection entry and quickly open the Apps.

Stay on home page, press “left” key until the end to open input shortcut entry at the left side of screen, and choose preferred input source.

When App’s operation breaks down, use “Clear memory” App to clean the backstage, then enter again.

Scan the provided QR code to download XGIMI assistant. The XGIMI assistant provides mobile phone remote control functionality, allowing the device to be easily controlled by a mobile phone. It also enables mobile phone resource sharing to the device to view photos or videos, and mirroring display control to a mobile phone, supporting gravity sensor games.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.