XGIMI ELFIN FLIP (01) PDF Document

You should read this user guide carefully before using the product for both your safety and interest.

Screen Off: Only switch off the display. Other parts are still working.

Sleep: The projector will reboot quickly next time.

Restart: Restart the projector completely.

Shutdown: Switch off the projector completely.

Step 1: Connect the power supply and rotate the body to reveal the power button.

Step 2: Press the power button to turn on the projector.

Step 3: Rotate the body to a suitable angle and enter viewing mode.

Press the power button on the remote control for the projector to enter sleep mode.

Press the power button on the projector body for the projector to enter sleep mode.

Long-press the power button on the remote control, select “Shutdown” from the on-screen menu, and the projector will power off.

Press the power button on the projector body for 5 seconds to turn off the power.

Rotate the body to a suitable angle for viewing, then press the power button on the projector to turn on the projector.

When the projector is asleep, rotate the body to a suitable angle for viewing, then press the power button on the remote control to turn on the projector.

Position the remote control within 10cm of the device, long-press the power button and the home button simultaneously. An indicator light will begin flashing as the remote control enters pairing mode. Release the buttons when the flashing begins. After hearing a “ding” sound, the connection is successful. If pairing fails, wait for 30 seconds and repeat the steps above.

Short-press the focus button on the remote control for auto-focus. Long-press for manual focus, adjust manually using the left and right buttons on the D-pad.

Online upgrades can be performed through the system settings. You can access system settings by pressing the home button.

Do not stare directly into the projector lens or have it facing you as the light may be harmful to your eyes. As with any bright source, do not stare into the direct beam (RG2 IEC 62471-5:2015).

Do not block the device’s air inlet/outlet to prevent heat dissipation issues and damage to the internal electronic components.

Do not wipe the lens with cleaning paper, cloth, or other materials as doing so may damage the lens. Please use an air blower to remove dust from the lens instead.

Do not wash the device with cleaning chemicals, detergents, or any other liquid to prevent the circuit board from corroding. Avoid exposing the device to rainwater, moisture, and mineral-containing liquids.

Keep the device, its components and accessories, out of the reach of children.

Make sure that the device is used in a dry and ventilated environment.

Do not store the device in extremely hot or cold temperatures as doing so will shorten the life of the device. Place and use the device in an environment of 0°C-40°C.

Do not put the device into any heating equipment (such as a dryer or microwave oven) for drying.

Do not squeeze the device or place any obstructions above or behind it to avoid damaging the device and blocking the light path.

Do not throw, strike, or sharply vibrate the device to prevent damaging the internal circuit board.

Do not try to disassemble and assemble the device yourself. If any issue occurs, please contact the after-sales service of XGIMI.

Do not repair any product on your own. If the device or any component does not work properly, consult the after-sales service of XGIMI in a timely manner or return the defective product to XGIMI for repair.

Due to different HDMI specifications, some HDMI cables and devices may not be compatible with the product. Using uncertified HDMI cables may cause display or connection failures. Please use HDMI cables with good radiation shielding.

Please sleep or turn off the device before closing the body and frame.

Operation is subjected to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received, including interference that may cause undesired operation.

The user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

In the installation and operation of the device, the distance between the transmitter and a human body should be at least 20 cm.

The 5.150-5.250 GHz frequency range is only for indoor use.

Bluetooth transmitter frequency range: 2402 MHz -2480 MHz.

Bluetooth transmitter power: < 10 dBm(EIRP).

Wi-Fi network: IEEE 802.11 a/b/g/n/ac (2.4GHz/5GHz).

2.4G Wi-Fi transmitter frequency range: 2412 – 2472 MHz.

2.4G Wi-Fi transmitter power: <20 dBm (EIRP).

5G Wi-Fi transmitter frequency range: 5.15-5.35GHz, 5.470-5.725GHz, 5.725-5.850GHz.

5G Wi-Fi transmitter power:

5.15-5.25GHz < 23dBm(EIRP), 5.25-5.35GHz < 20dBm (EIRP)

5.470-5.725GHz < 20dBm (EIRP), 5.725-5.825GHz < 13.98dBm(EIRP).

This product shall only be connected to a USB interface of version USB2.0 (5VDC, 0.5A).

Adapter shall be installed near the equipment and shall be easily accessible. The plug considered as disconnect device of adapter.

Power supply and ADP (rating):

Input: AC 100 V-240V, 50/60 Hz, 1.5A

Output: DC 19.0V, 3.42A

The device complies with RF specifications when it is used at a distance of 20 cm away from your body.

To prevent possible damage to hearing, do not listen at high volume levels for long periods.

CAUTION:

– Risk of fire or explosion if the battery is replaced by an incorrect type.

– Replacement of a battery with an incorrect type that can defeat a safeguard (for example, in the case of some lithium battery types);

– Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;

– Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas;

– A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development (ISED) Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and

(2) This device must accept any interference, including interference that may cause undesired operation of the device.

This device complies with Part 15 of the FCC rules. Operation is subjected to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.