VORWERK THERMOMIX TM6 (01) PDF Document

If water gets into the electrical components of your VORWERK THERMOMIX TM6, you could get an electric shock. Follow these precautions:

• Do not immerse the base unit in water or other liquids.

• Do not hold the base unit under running water.

• Do not pour water over the base unit.

• Disconnect the appliance from the mains power supply before cleaning the base unit.

• Clean the base unit with a dry or damp cloth only.

• No water or dirt should enter the base unit.

• Do not use the VORWERK THERMOMIX TM6 outdoors.

• If water has managed to get into the appliance, contact your Vorwerk repair service.

An incorrectly installed power connection or a damaged base unit or power cord can cause an electric shock. Please observe the following:

• Only connect the base unit to a plug installed by a qualified specialist.

• Regularly inspect the base unit, power cord, and accessories for possible damage.

• Ensure that the power cord does not touch hot surfaces or external heat sources.

• Never use your VORWERK THERMOMIX TM6 if the power cord is damaged.

• Do not use the base unit if it is dropped or damaged in any way.

• In the event of damage to the base unit or the power cord, return your VORWERK THERMOMIX TM6 to the Vorwerk repair service for examination, repair, or electrical or mechanical adjustment.

• If the power cord on the base unit has been damaged, it must be replaced by the manufacturer, its repair service, or a similarly qualified person to avoid hazards.

• Never attempt to repair the base unit yourself.

• Never put your fingers into the openings that are intended for the contact pins on the base of the mixing bowl and do not insert any objects into these openings.

• Only operate the VORWERK THERMOMIX TM6 with the alternating current voltage of 230 V and mains frequency of 50 Hz, as stated on the plug label (these values are only valid for Europe).

To prevent fire hazards with your VORWERK THERMOMIX TM6, follow these guidelines:

• Do not put the base unit on a stove (hob, ceramic hob, induction hob, or similar) or on any other heated or heatable surface.

• Keep the appliance a sufficient distance from hot surfaces and external heat sources.

• Ensure that the power cord does not touch hot surfaces or external heat sources.

• The VORWERK THERMOMIX TM6 has a high power consumption. Please note the maximum power consumption when connecting the base unit to avoid fire from an insufficient power rating.

• Do not use multiple socket extension leads or other devices to connect the VORWERK THERMOMIX TM6 to the power socket.

To prevent the risk of scalding from hot contents, please adhere to the following safety measures:

• To allow steam to escape and prevent excess pressure, ensure the opening in the mixing bowl lid is never blocked or covered, either from the inside (e.g., by food) or from the outside (e.g., by a towel).

• Never cover the opening in the mixing bowl lid with anything but the accompanying original accessories (measuring cup, simmering basket, splash guard, and Varoma® dish).

• Do not fill the simmering basket past the max. fill line.

• If you notice the opening in the mixing bowl lid is blocked or the measuring cup is being pushed up, unplug the base unit. Do not touch the controls.

• Do not fill the mixing bowl past the max. fill line (2.2 litres).

• Ensure that the opening in the mixing bowl lid remains free of food.

• Take extra care when adding liquids to the mixing bowl.

• Remove the mixing bowl carefully from the base unit to help prevent contents from spilling or splashing.

• If you deviate from recipe instructions and cook larger quantities of food at higher temperatures (> 90°C), the food can boil over. Take extra care when cooking at high temperatures.

• If boiling over occurs, push the selector to switch off the VORWERK THERMOMIX TM6.

• Do not use the Turbo Mode for hot food or liquid over 60°C.

• When blending hot food, increase the speed gradually.

Steam is generated during cooking, particularly when using the Varoma®, which can scald you. Follow these precautions:

• Keep away from the steam.

• When preparing hot food, do not touch or cover the measuring cup. Make sure that the steam between the measuring cup and the opening in the mixing bowl lid can escape.

• Ensure that some slots in the Varoma® dish and Varoma® tray remain free of food to allow the controlled escape of steam.

• Ensure that the Varoma® dish is correctly positioned on the mixing bowl lid so that it does not tip and fall off. Do not place the Varoma® on the splash guard.

• When removing the Varoma® from the mixing bowl lid and setting it aside, always keep the Varoma® lid on.

• When removing the Varoma® lid, tilt the lid away from the face and body to avoid escaping steam.

The High Temperature Mode heats fat, and mixtures of water and oil may spit, which can cause burns. Follow these safety instructions:

• Never pour fat that has already been heated into the mixing bowl.

• Never heat oil at High Temperature without other ingredients. If there is a delay in adding the ingredients, the hot fat will spit excessively.

• Make sure that all VORWERK THERMOMIX TM6 accessories used are dry.

• Follow the instructions on the display.

• Always place the splash guard correctly onto the mixing bowl lid as soon as your VORWERK THERMOMIX TM6 instructs you to do so.

• Ensure that the locking arms cover the splash guard.

Improper use of the mixing bowl lid can lead to scalding if hot contents escape. To ensure safe operation:

• Never try to open the mixing bowl lid or the locking mechanism using force.

• Only open the mixing bowl lid when the speed is set to “0” and the locking mechanism has released it.

• Inspect the sealing ring regularly for possible damage. In case of damage or leakage, replace the lid immediately.

• Only use the VORWERK THERMOMIX TM6 with a clean mixing bowl lid. The rim of the mixing bowl and the sealing ring must always be kept free of food residues to ensure that the lid is properly sealed.

To avoid injury and ensure safe operation, please follow these guidelines for your VORWERK THERMOMIX TM6 and its accessories:

• Use only the recommended original Vorwerk Thermomix® accessories.

• Never use the VORWERK THERMOMIX TM6 in combination with parts or equipment for older generations of Thermomix®.

• Do not modify your VORWERK THERMOMIX TM6 or any of the accessories.

• Never use your VORWERK THERMOMIX TM6 with damaged accessories.

• When stirring, only use the supplied spatula and place only the flat end in the mixing bowl.

• Use care when removing the hot simmering basket. Ensure the spatula is hooked securely before lifting it.

• Place the VORWERK THERMOMIX TM6 on a clean, solid, and even surface, away from the edge, as kneading or chopping may cause it to move.

• Never leave the appliance unattended while running.

• If any accessories are damaged by the mixing knife, discard the food and contact Customer Care for replacements.

Cooking methods like slow cooking, fermenting, and sous-vide cooking operate at low temperatures (below 100°C), which can allow germs to spread. To mitigate health risks:

• Ensure hygienic working practices at every stage of the food preparation and cooking process.

• Follow the instructions in the recipe exactly (temperature and time).

• Once food has been cooked according to the recipe, make sure that it is consumed immediately or that it is correctly preserved/stored.

To prevent burns from hot surfaces and injuries from sharp blades or moving parts:

• Handle the mixing bowl, mixing knife, and accessories with care during and after preparing hot food, as they will be hot.

• Only use the designated handles and grips when touching all components.

• Allow the mixing bowl and knife to cool sufficiently before dismantling.

• The blades on the mixing knife are sharp. Handle the mixing knife with care, never take hold of it by the blades, and be careful to prevent it from falling out when removing it.

• Do not reach into the mixing bowl and keep body parts and hair away from the mixing knife.

• To avoid pinching your fingers, avoid contact with the moving locking arms on the base unit or under the mixing bowl lid. Keep hair and clothing away from these parts.

To prevent damage to your appliance and accessories, please follow these guidelines:

• **Steam Damage:** Ensure there is sufficient clearance above and around the VORWERK THERMOMIX TM6, especially when using the Varoma®, to prevent steam from damaging furniture or fittings.

• **Improper Cleaning:** Always clean components directly after use. Do not leave the mixing knife in water for a long time. Ensure the mixing bowl and its contact pins are fully dry before inserting into the base unit to prevent corrosion.

• **Incorrect Assembly of Mixing Knife:** Ensure the sealing ring is fitted correctly and is not damaged. Lock the mixing knife into place correctly before filling the bowl to prevent moisture from damaging the base unit.

• **Improper Use of Butterfly Whisk:** Ensure the whisk is correctly attached before setting the speed. Do not exceed speed 4, do not use the spatula, and do not add ingredients that could damage or block the whisk.

• **Improper Use of Varoma®:** Ensure there is enough water in the mixing bowl (approx. 250 ml of water evaporates in 15 minutes). Top up water if necessary.

The delivery for the VORWERK THERMOMIX TM6 includes the following items:

1. Thermomix® TM6 base unit

2. Mixing bowl base

3. Contact pins

4. Mixing bowl

5. Mixing knife and sealing ring

6. Mixing bowl lid

7. Measuring cup

8. Splash guard

9. Simmering basket with lid (permanently attached)

10. Varoma® dish

11. Varoma® tray

12. Varoma® lid

13. Spatula

14. Butterfly whisk (stirring attachment)

15. Instruction manual and cookbook (optional)

Follow these steps for the initial setup of your VORWERK THERMOMIX TM6:

1. Choose a permanent, clean, solid, and even setup location in your kitchen, ensuring it’s not on a hot surface and is away from heat sources.

2. Ensure there is sufficient distance between the appliance and the edge of the work surface.

3. Ensure the ventilation opening on the back of the appliance is kept clean.

4. Remove the protective foil from the touchscreen and the locking arms.

5. Gently pull the power cord out of the housing to your desired length (up to 1m) and connect it to the mains power supply. Do not place the base unit on the power cord.

6. Press the selector to start up the VORWERK THERMOMIX TM6. The transportation mode will be automatically deactivated.

7. Follow the on-screen instructions to complete the basic settings.

To disassemble the mixing bowl for thorough cleaning, proceed as follows:

1. Hold the mixing bowl so that the opening points upwards.

2. Turn the mixing bowl base 30 degrees clockwise away from the handle and pull the mixing bowl base off downwards. This may be stiff initially. The mixing knife will remain in the mixing bowl.

3. Carefully take hold of the mixing knife above the blades and remove it, together with its sealing ring, from the mixing bowl.

To reassemble the mixing bowl after cleaning, follow these steps:

1. Ensure that the sealing ring of the mixing knife is correctly positioned under the knife bearing.

2. Hold the mixing bowl with the opening pointing upwards.

3. Carefully hold the mixing knife above the blades and insert it, with its sealing ring, into the hole in the bottom of the mixing bowl until the sealing ring touches the base of the bowl.

4. Attach the mixing bowl base to the bottom of the mixing bowl.

5. Turn the mixing bowl base 30 degrees counter-clockwise towards the handle to lock the mixing knife firmly in place.

6. Check that the mixing bowl base is firmly in place. The mixing bowl will only go into the base unit if it has been correctly assembled.

The measuring cup is used to close the opening in the mixing bowl lid, preventing food from escaping and preventing heat loss. It can also be used to measure liquids, with 50 ml and 100 ml markings.

• **Adding small amounts of liquid:** You do not need to remove the measuring cup. Simply pour the liquid slowly onto the lid, and it will trickle into the mixing bowl.

• **Adding larger quantities or ingredients:** To remove the measuring cup, gently pull it towards you, then tilt it upwards and lift it out.

The butterfly whisk is used for whipping cream, whisking egg whites, and making puddings and sauces.

How to Insert the Butterfly Whisk:

1. Place the butterfly whisk onto the mixing knife and slightly turn it against the intended rotation of the mixing knife.

2. Make sure that the butterfly whisk is hooked into place and does not come off if pulled upwards.

How to Remove the Butterfly Whisk:

• Hold the ball-shaped end of the butterfly whisk and pull it out by gently rotating in both directions.

Important Usage Notes:

• Ensure the whisk is correctly attached before setting the speed.

• Do not exceed speed 4 when the butterfly whisk is fitted.

• Do not use the spatula when the butterfly whisk is fitted.

To safely remove the hot simmering basket, use the supplied spatula. Proceed as follows:

1. Place the hook of the spatula into the notch of the simmering basket. Ensure that the hook is securely attached.

2. Using the handle of the spatula, lift the simmering basket out of the mixing bowl. You can then transfer it to a sink to drain.

3. Once you have put the simmering basket down, remove the spatula by releasing the hook from the notch. This prevents the basket from tipping over.

Switching On:

• Press the selector. The VORWERK THERMOMIX TM6 will switch on and the default start page will appear.

Switching Off:

1. Hold the selector down for approximately 5 seconds until a confirmation message appears.

2. Release the selector.

3. After switching off, unplug the appliance when not in use.

Note: To save energy, the appliance switches off automatically after 15 minutes when not in use. A message appears for the last 30 seconds, allowing you to cancel the shutdown.

The start screen shows three dials for manual cooking: time, temperature, and speed.

• **Setting the Time:** Tap the time dial (00:00) and turn the selector to set the required time. You can adjust the time at any point during cooking.

• **Setting the Temperature:** Tap the temperature dial (— °C) and turn the selector to set the desired temperature. The heating function only works if a time has been set.

• **Setting the Speed:** Tap the speed dial (0) and turn the selector to set the desired speed. This will start the appliance.

You can also briefly press the selector to jump between the different dials.

The VORWERK THERMOMIX TM6 has various speed settings for different functions:

Note: The heating deactivates at speeds higher than speed 6.

The reverse knife movement allows for gentle stirring of delicate food without chopping it.

1. Tap the reverse symbol on the speed dial. This switches the rotating direction of the mixing knife from forward (clockwise) to reverse (counter-clockwise). The reverse symbol will be shown on the display.

2. To stop reverse operation, either tap the reverse symbol again or wait until the set time has expired, at which point the rotation automatically returns to the forward knife movement.

To steam with the Varoma®, follow these steps:

1. Place the mixing bowl correctly into the VORWERK THERMOMIX TM6.

2. Pour at least 0.5 litres (500g) of water into the mixing bowl for up to 30 minutes of steaming.

3. If steaming with the simmering basket (e.g., for potatoes or rice), insert it now.

4. Close the mixing bowl with the mixing bowl lid.

5. Place the Varoma® lid upside down on your work surface and position the Varoma® dish on top.

6. Loosely fill the Varoma® dish with food, ensuring some slots remain unobstructed for steam to circulate. Place food requiring a longer cooking time at the bottom (Varoma® dish) and food with a shorter cooking time at the top (Varoma® tray).

7. Select the required steaming time and Varoma temperature using the dials.

8. Turn the selector to a low speed setting (up to speed 6) to begin the steaming process.

To weigh ingredients accurately, follow these steps:

1. Place the mixing bowl in the base unit and touch the scales icon on the Modes and Tools screen.

2. Weigh the first ingredient (up to 3.0 kg max.).

3. To add more ingredients, tap the “tare” button to reset the scale to zero, then add the next ingredient.

4. Repeat step 3 as needed up to a total maximum weight of 6 kg.

Tip: For accurate results, do not touch the VORWERK THERMOMIX TM6 while weighing, do not lean anything against it, and make sure the power cord is without tension.

To connect your VORWERK THERMOMIX TM6 to a WiFi network:

1. Select Main Menu > Settings > WiFi.

2. Activate WiFi by pressing the slide control on the right-hand side. A list of available WiFi networks will be displayed.

3. Select the WiFi network to which you want to connect.

4. Enter the password for your selected WiFi network and press Connect.

If the connection is successful, the status will change to “Connected” and a green tick will appear next to the network name.

Transportation mode secures the mixing bowl and lid with the locking arms, allowing you to move your appliance safely.

1. Make sure that the mixing bowl, including its lid, is correctly inserted in the base unit.

2. Select Main Menu > Transportation Mode.

3. Activate the mode using the slide control.

The locking mechanism will activate. You can now switch off your VORWERK THERMOMIX TM6 and transport it safely.

Accessories (Mixing Bowl, Lid, Knife, etc.):

• All components (except for the base unit) are dishwasher-safe. Place plastic parts, particularly the mixing bowl lid, in the top rack of the dishwasher.

• For thorough cleaning, disassemble the mixing bowl. Clean all parts by hand or in the dishwasher.

• Wipe the contact pins on the bottom of the mixing bowl and ensure they are clean and dry before putting the bowl back in the base unit.

• You can use the “Pre Clean” mode for a quick clean between recipe steps.

Base Unit:

1. Disconnect the appliance from the mains power supply before cleaning.

2. Wipe the base unit with a damp cloth and a gentle cleaning agent.

3. Use water sparingly to prevent moisture from entering the base unit.

Never immerse the base unit in water.

The mixing knife will wear out over time, especially with regular use for chopping hard food. Recommended replacement intervals are:

• Unplug the appliance immediately.

• Use a towel to dry excess liquid from underneath the mixing bowl.

• To prevent liquid from getting into delicate components inside the base unit, do not move it or turn it over.

• Do not attempt to disassemble the appliance. It does not contain any parts that you can service yourself.

• If you cannot be certain that no liquid has entered the base unit, do not switch on your VORWERK THERMOMIX TM6. Instead, contact Customer Care.

The base unit may not be connected correctly. Check if the power cord has been properly plugged in.

This could be due to two reasons:

• The heating time may not have been set correctly. Check whether you set a time using the time dial.

• The temperature may not have been selected. Check if you set the temperature.

The motor may have turned off. Follow these steps:

• Remove the mixing bowl from the base unit.

• Reduce the quantity contained in the bowl and/or add some liquid.

• Wait for approx. 5 minutes (cooling down time).

• Place the mixing bowl back into position.

• Check that the air intakes at the back of the base unit are unobstructed.

• Turn the dial to re-start the appliance.

If the error message is still displayed after the cooling time, please contact Customer Care.

The VORWERK THERMOMIX TM6 may not have been positioned correctly.

• Make sure that nothing is leaning against the base unit.

• Make sure that there is no tension on the power cord.

• Make sure that the VORWERK THERMOMIX TM6 is placed on a clean, level, non-slip surface.

• Do not touch the VORWERK THERMOMIX TM6 during the entire weighing process.

There may not be a network available or the WiFi function may be deactivated.

• Check your WiFi.

• Set up a network by going to Main Menu > Settings > WiFi.

If it is not possible to set up a network, contact Customer Care.

Motor: Maintenance-free Vorwerk reluctance motor, 500 W rated power. Speed continuously adjustable from 40 to 10,700 rpm. Special speed setting for dough kneading. Electronic motor protection to prevent overload.

Heating system: 1,000 W power consumption. Protected against overheating.

Integrated scales: Measuring range from 1 to 3000 g and -1 to -3000 g.

Housing: High-quality plastic material.

Mixing bowl: Stainless steel, with integrated heating system and temperature sensor. Maximum capacity 2.2 litres.

Connected load: Only for 220-240 V 50/60 Hz (TM6-1). Maximum power consumption 1500 W. Pull-out power cord, 1 m long.

Standby power consumption: 0 W.

Information on connectivity: 2.4 GHz: IEEE Standard 802.11b/g/n™. 5 GHz: IEEE Standard 802.11n/a/ac™. Bluetooth® Specifications Version 4.2. Bluetooth® Low Energy Specifications Version 4.2.

Dimensions of base unit: 34.10 cm x 32.60 cm x 32.60 cm (height x width x depth).

Dimensions of Varoma®: 13.10 cm x 38.30 cm x 27.50 cm (height x width x depth).

Weight of base unit: 7.95 kg.

Weight of Varoma®: 0.80 kg.