VONHAUS 3519001 (01) PDF MANUAL

The package contains the following items:

A. Cordless Brushcutter

B. Mounting Screws x 2

C. T-Key with Hexagon x 1

D. Cutting Blade x 1

E. Carrying Belt x 1

F. Protective Guard x 1

G. Aluminum Handlebar Frame x 1

H. Batteries x 2

I. Battery Charger x 1

J. On/OFF Trigger x 1

K. Allen Key

L. Line Spool

To assemble the handle, follow these steps:

• Align the handlebar with the aluminum frame.

• Secure the upper clamp with 4 bolts.

To install the shaft tube:

• Insert the aluminum tube into the hole.

• Tighten the locking knob.

Attach the protective cover to the motor housing with the two provided screws using the hexagon wrench (the T-wrench with hexagon).

In order to mount a reel or knife, the spindle must always be locked.

To lock the spindle, press the spindle locking pin and keep it pressed while you are tightening or loosening the attachment.

1. Put the blade onto the lower blade holder.

2. Add the upper blade holder, ensuring the convex side is facing out.

3. Hold the spindle lock and tighten the nut clockwise.

Safety: Always wear gloves when handling the blade. Keep the blade clean and use the blade cover when the tool is not in use.

To attach the strap:

• Connect the strap to the mount on top of the main unit.

• Place the strap over your RIGHT shoulder only.

• Keep the motor unit on your right side.

To adjust for comfort:

• Adjust the strap length until it is comfortable.

• Practice swinging the unit without starting the motor to check the feel.

• Find your balance point before starting work.

SAFETY WARNING:

• Never wear the strap diagonally across your chest.

• Keep the strap on one shoulder only. This allows for quick removal in case of an emergency.

TIP: Before starting work, perform a few practice movements to ensure everything feels balanced and secure.

This 2-in-1 cordless brush cutter is designed for private, non-commercial use. It serves two functions:

• Mowing lawns, weeds, and long grass.

• Trimming shrubs and bushes.

The tool is for adult use only. Any other use is considered improper.

• Keep the work area clean and well-lit.

• Avoid explosive environments.

• Keep children away from the work area.

• Use proper plugs and outlets.

• Avoid wet conditions.

• Use appropriate extension cords.

• Install a residual current circuit breaker in damp conditions.

• Stay alert while operating.

• Use protective equipment.

• Prevent accidental starts.

• Maintain proper posture.

• Wear appropriate clothing.

• Don’t overload the device.

• Maintain tools properly.

• Keep cutting tools sharp.

• Use appropriate accessories.

• Store safely away from children.

• Use only recommended chargers.

• Keep the battery away from metal objects.

• Avoid contact with battery fluid.

• Service should only be performed by qualified professionals.

• Ensure the tool is off before inserting a battery.

• Charge batteries indoors only.

• Allow hot batteries to cool before charging.

• Operating temperature: 4° to 40°C.

• Storage temperature: 0° to 50°C.

• Remove the battery before storing the tool.

When operating in brush cutter mode:

• Always wear heavy gloves when handling blades.

• Never touch rotating blades.

• Keep both hands on the handles until the blade stops completely.

• Check blades before each use; replace if damaged.

• Use only manufacturer-approved blades.

• Cut from right to left for better control.

• Always use both hands to operate.

• If you hit an obstacle, this technique helps minimize blade kickback.

CAUTION: Moving blades can cause serious injury.

• Keep ventilation slots dust-free to prevent the motor from overheating.

• Clean the housing with a soft cloth after each use if possible.

• For stubborn dirt, use a soft cloth dampened with soapy water.

• Keep the device and charger connections clean.

CAUTION: Never use solvents like gasoline, alcohol, or ammonia water as they can damage plastic parts.

• Nominal Voltage: 36V DC (2 x 18V DC)

• Rotation Speed (First Gear): 6000 RPM

• Grass Trimmer (Wire Spool): 340mm cutting circle

• Brush Cutter (Blade): 255mm cutting circle

• Sharp edges: Be aware of sharp components.

• Protect your ears: Wear hearing protection.

• Protect your eyes: Wear eye protection.

• Protect your hands: Wear protective gloves.

• Wear suitable footwear: Use sturdy, non-slip footwear.

• Protective clothing must be worn: Wear appropriate protective clothing.

• Beware of kickback: Be prepared for the tool to kick back suddenly.

• Potential finger trap points: Be careful to avoid pinching your fingers.

• Maintain a safe distance from bystanders: Ensure others are a safe distance away during operation.

• Do not use in wet conditions: Avoid using the tool in rain or damp environments.

Please recycle where facilities exist. Check with your local authority for recycling advice.