VONHAUS 3000070 (01) PDF MANUAL

This product is intended for use in private households.

This product is not intended for use in commercial or industrial environments.

It is not suitable for use outdoors.

This product is not intended for use in damp or humid environments.

This product is not a toy. Children should be supervised at all times to ensure they do not play with this product.

The fixings contain small parts which pose a choking hazard to children and animals. Keep out of reach.

Before assembly, unpack carefully and check that all components are included. Read this Manual carefully and count all fixings before proceeding.

It is recommended that this product is assembled and housed on a level and dry surface.

Do not exceed 29 kg / 4.56672 st.

Allow adequate working space.

Ensure there is sufficient lighting.

Wear suitable protective clothing. Protective gloves and footwear are recommended.

Assemble and locate for use on a suitable level floor surface.

Assemble this product as close to its final position (in the same room, if possible).

Do not drag this product into position. Always carefully lift into position.

Assemble with care, particularly when lifting or stretching, and when using tools.

Dispose of packaging materials responsibly.

This product should only be used on firm level ground.

Ensure the Legs/Base remain in contact with the ground at all times.

Do not stand on this product.

The exclamation mark symbol with “WARNING!” indicates to pay attention to all safety and guidance.

The book symbol with “IMPORTANT” indicates to read the manual before use.

The hand symbol with “INTENDED PURPOSE” indicates not to use for anything other than for what it is intended.

Insert 6 pieces of Minifix A2 into the designated holes on component 1 and rotate them to secure.

Attach 12 pieces of Minifix A1 into component 3 and press. Insert 6 pieces of Minifix A2 into components 4 and 5, then rotate to secure. Attach 20 pieces of Ø8x30mm Wood Dowel B into component 6 and press.

For each of the 2 sets of 12″ Soft Closing Drawer Slide J, press the release lever on J2 to separate J1 from J2.

Attach 3 pieces of M3.5x16mm C.B Screw D to each of the 3 J1 slide components, then rotate to secure. These J1 slides are attached to components 2, 3, and 5.

Use 2 pieces of M6x50mm CSK Cap Wood Screw C with the Allen Key M4 F to secure component 4 to component 6 by rotating.

Connect component 1 to component 3 using 4 pieces of Minifix A2, rotating to secure.

Connect component 4 to components 1, 3, 5, and 6 using 8 pieces of Minifix A2, rotating to secure. Insert 8 pieces of Minifix A1 and Minifix A3 into components 3 and 5, and press them into place. Additionally, use 8 pieces of M3.5x16mm C.B Screw D to secure component 4 to the unit, rotating to tighten.

Use 6 pieces of M6x50mm CSK Cap Wood Screw C to attach components 3, 4, 7, and 8 to the main unit, rotating to secure.

Attach 4 pieces of Metal Support Leg H to component 15 by rotating them into place.

Use 20 pieces of M4x30mm C.B Screw G to attach 4 pieces of Stud 192 with Screw I to component 17. Note that component 16 has a Plastic adjuster at the bottom to unscrew and adjust its height if necessary. Use 1 piece of Stud 192 with Screw I on component 16, rotating to secure.

Attach 8 pieces of Stud 192 with Screw I to components 3, 4, 7, and 8 by rotating them into place.

Use 8 pieces of M4x38mm C.B Screw E to attach component 13 to components 11, rotating to secure.

Assemble the drawer components 9, 10, 11, 12, 13, and 14 using the previously attached M4x38mm C.B Screw E.

Attach 4 pieces of M3.5x16mm C.B Screw D to the J2 part of the 12″ Soft Closing Drawer Slide, rotating to secure. These J2 slides are attached to components 9 and 10.

Insert the assembled drawers into the unit, aligning the J1 and J2 slides, and press to engage them.

Please recycle where facilities exist. Check your local authority for recycling advice.