VIVOSUN WP-0001 (01) PDF DOCUMENT

The VIVOSUN WP-0001 pump includes several features for safety and performance:

Built-In Thermal Protection: When the motor is overheating, the pump will automatically stop running until the temperature reduces to an appropriate and safe level. Once it reaches this temperature, it will start operating again.

Automatic Pressure Switch Control: This is an automatic diaphragm pump with a pressure switch. It starts automatically when the faucet is switched on and stops working automatically when the faucet is switched off.

Pure Copper Motor: The pump is equipped with a 100% copper motor that has an overload and overheat protection function. When the motor overheats, it can automatically disconnect the power to the electronic circuits. Compared to other models, it has higher performance, less noise, and higher speed, enabling it to operate safely and reliably.

Iron Fixing Plate: The anti-vibration fixing plate at the base can greatly reduce the motor’s noise output. With the galvanized anti-rust treatment on the surface of the plate, it resists corrosion and will not rust easily even in a humid environment.

Standard Accessories: We use the standard 1/2″ thread for easier operation and quicker installation.

1. Please make sure the water pump is connected tightly to the inlet and outlet pipes. Several problems may occur such as low pressure, insufficient water suction, and water leakage, etc.

2. Install a filter at the inlet end. The optimal density of filtration is above 50 mesh.

3. Connect the power supply to the water pump. The output parameters of the connected power supply must meet the motor’s input requirements.

4. Turn on the power. The pump will run water for 5-10s, draining water and driving air out of the pipelines. When the water output is stable, turn off the power temporarily and connect the pump to the water gun, faucet, shower, or other similar devices that can supply water.

5. Turn off the water faucet when it is not in use. The faucet has an automatic pressure control switch. If you turn on the tap once, it will work automatically the next time.

1. When the pump is working, it is necessary to ensure smooth drainage to avoid blocking and causing damage to the pressure switch.

2. If you hear a strange ticking sound from the switch during operation, please turn off the pump immediately and turn up the pressure appropriately.

3. The motor is slightly waterproof, so don’t worry too much if a bit of water gets on it. We recommend drying it as soon as possible. It is strictly forbidden to immerse the motor in water. If the motor is used outside, it should be protected with a cover to prevent water from contacting the motor and potentially causing power failure, leakage, or motor damage.

4. The water inlet must have a filter. Impurities in the liquid may block the pump, resulting in a series of problems like lower pressure, lower flow, pump damage, and failure to pump water. It is strictly forbidden to use this pump without connecting the filter. The optimal filter density is more than 50 mesh.

5. Warning: Please use the 115V AC motor. The use of 220V is prohibited, as it will burn the motor directly.

6. The pump can convey water, weak acids, alkalis, salts, and other liquids. It is not allowed to convey liquids with particles, gasoline, and other combustible liquids.

7. The water pump does not support 24-hour continuous work. Intermittent work will help extend the life of the pump. Please turn off the power to the pump when not using the pump for extended periods.

8. The water pump features an automatic pressure switch to allow you to adjust the pressure freely as needed. Avoid the extremes, as too low pressures will result in frequent starting and stopping and even motor burns, whereas too high pressures will cause the pump to shut down abnormally.

9. After using this pump during a cold winter please drain any excess water as freezing will cause cracks in the water pipes.

10. The water pump has been tested for performance. Please do not disassemble it by yourself. Check the power supply before use; the power supply parameters must be consistent with the motor pump input parameters.

11. Proper installation requires placing the pump head down or flat to avoid water leakage into the rotor.

The F33 series AC diaphragm pump is widely used in yachts, RVs, agricultural irrigation, industrial plants, liquid transfers, water purifier boosters, solar water systems, car washes, and more.