Free English VENTS NB MICRA 100 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD VENTS NB MICRA 100 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What is the purpose of the VENTS NB MICRA 100 outer ventilation hood?
The outer ventilation hood (hereinafter referred to as the “hood”) for the VENTS NB MICRA 100 is designed to prevent ingress of water and foreign objects into the ventilation equipment from outside.
What items are included in the DELIVERY SET for the VENTS NB MICRA 100?
The delivery set for the VENTS NB MICRA 100 includes the following:
Hood: 1 pc.
Installation instruction: 1 pc.
Fastening kit: 1 pc.
Packing box: 1 pc.
What are the overall dimensions for the VENTS NB MICRA 100?
The dimensions in [mm] for the VENTS NB MICRA 100 are as follows:
| Model | Ø d | Ø D | A | A1 | A2 | B | H | H1 |
| NB MICRA 100 | 4.8 | 98 | 648 | 530 | 400 | 107 | 230 | 150 |
What is the first step in installing the VENTS NB MICRA 100 outer hood?
Step 1 of installation is to insert the air duct from indoor to protrude from outside on the outer wall surface. Then, cut the air duct excess with a hack saw or with any other suitable tool, leaving 10-12 mm protruding.
How should the VENTS NB MICRA 100 hood be prepared for mounting hole marking?
To prepare the VENTS NB MICRA 100 hood for mounting hole marking, disassemble the hood to enable access to the fastening holes. This is done by removing the screws that secure the front part of the hood and then removing the front part.
What drilling is required for installing the VENTS NB MICRA 100 outer hood?
Mark the mounting holes using the back part of the ventilation hood. Then, drill 4 holes for 6×40 dowels to a depth of 50 mm.
How should the back part of the VENTS NB MICRA 100 hood be affixed to the wall?
Insert the supplied expansion anchors 6×40 into the drilled holes. Then, fix the back part of the hood on the wall using the supplied screws 4×40.
What is the final step in assembling the VENTS NB MICRA 100 outer hood after fixing the back part?
Place the front part of the hood on the back part and secure it with screws.
What precautions should be taken regarding installation of the VENTS NB MICRA 100 at high altitudes?
If the mounting place for the VENTS NB MICRA 100 is located at high altitude, please refer to a mounting company possessing an appropriate mounting equipment.
Who should operate the VENTS NB MICRA 100 unit?
The unit should not be operated by children or persons with reduced physical, mental, or sensory capacities, or those without the appropriate training.
Who must install and connect the VENTS NB MICRA 100 unit?
The unit must be installed and connected only by properly qualified personnel after the appropriate briefing.
What consideration must be given to the choice of installation location for the VENTS NB MICRA 100 unit?
The choice of unit installation location must prevent unauthorised access by unattended children.
CLICK HERE TO DOWNLOAD VENTS NB MICRA 100 (01) PDF DOCUMENT