UNIONMAN WIFI6 CPE (01) PDF DOCUMENT

The UNIONMAN WIFI6 CPE has the following specifications:

Protocol: IEEE802.11ax with a maximum wireless rate of 3000m.

Bands: Supports 2.4G 2×2 and 5g 2×2.

Features: Support MU-MIMO.

Operating temperature: -20°C to 60°C.

Storage temperature: -40°C to 70°C.

Working humidity: 10% to 90% GH, non-condensing.

Storage temperature: 5% to 90% RH non-condensing.

Serial number	Name	Number	Company
1	WIFI6 CPE	1	PCS
2	The power adapter	1	PCS
3	Antenna (2.4G*2/5G*2)	4	PCS
4	Product manual	1	PCS

Part of the list above is for reference only, please refer to the real object.

The indicator light on the UNIONMAN WIFI6 CPE has the following meanings:

Solid Red Light: The equipment is powered on but not connected to the network.

Solid Blue Light: Networking is successful and the device is in normal operation.

Solid Red Light: There is a network off or fault condition.

Follow these steps for DIN rail installation of the UNIONMAN WIFI6 CPE:

1. Use a Phillips screwdriver to secure a metal spring (provided by the customer) to the front panel of the CPE. Secure the mounting fittings to the CPE with 2 screws with a torque of 1.2 N-m.

2. Insert the top of the DIN guide into the notch below the rigid metal spring.

3. Quickly press the DIN rail seat unit into the position shown in the figure.

To remove the UNIONMAN WIFI6 CPE from the DIN track, simply reverse steps 1, 2, and 3 above.

1. Remove the upper wall mounting plate from the CPE bottom plate.

2. Install the wall-mount panel onto the CPE as shown in the image.

3. Two screws are required to mount the CPE to the wall. The head diameter of the screw should be less than 8 mm and the straight diameter of the shaft should be less than 4 mm. Using the CPE with the wall mount installed, mark the correct position of the 2 screws. The vertical distance between the two screws should be 108.5mm.

4. Before fixing the screw to the wall, make sure the screw head fits the size of the handle by inserting the screw into one of the lock holes in the wall hanger. When fixing the screw to the wall, do not screw it in completely; leave about 2 mm of space for sliding the wall mounting panels.

5. After securing the screws to the wall, place the two screw heads through the larger part of the keyhole and slide the CPE vertically down. Finally, tighten the 2 screws to increase stability.

To connect the antennas to the UNIONMAN WIFI6 CPE, screw the external antenna female pin into the SMA joint in a clockwise direction, and tighten until the contact is good. There are two 2.4G antenna interfaces and two 5G antenna interfaces.

To restore the UNIONMAN WIFI6 CPE to factory settings, press the RESET button for more than 10 seconds. The equipment will then enter the process of restoring factory settings.

1. After the UNIONMAN WIFI6 CPE is energized, connect your computer to any LAN port of the CPE with a network cable.

2. Change the Ethernet property on your computer to a static IP (e.g., 192.168.1.10).

3. Open a browser and enter 192.168.1.1 to access the management interface.

4. Please check the sticker on your device for the default account and password to log in.

After logging in successfully to the management interface, enter the user management interface under the management menu. Here, you can change the login account and password.

Note: After changing your account and password, you will be forced to return to the login interface. You can then log in with the modified account and password.

The UNIONMAN WIFI6 CPE should be installed and operated with a minimum distance of 20cm between the radiator (the device) and your body.