TRIPP LITE B126-1A0-WP-1 (01) PDF Document

The TRIPP LITE B126-1A0-WP-1 has the following general features:

• Support a maximum video resolution of 1080p (60 Hz)

• Plug and play-no software or drivers required

• Support up to 7.1-channel surround sound audio

• HDCP and 3D compatible

The TRIPP LITE B126-1A0-WP-1 is an HDMI over Cat5 Active Extender Wall Plate with the following features:

• Works with B126-002 and B126-004 extender/splitters to extend a 1080i (60 Hz) signal up to 200 ft. from the source, or a 1080p (60 Hz) signal up to 150 ft. from the source

• Built-in equalization control for video image adjustment

• RJ45-style wall plate allows for the use of standard Cat5e/6 patch cables; 110 punchdown connection not required

The following optional accessories are available:

• B132-004-RB 1U Rack-Mount Bracket

• N202-Series Cat6 24 AWG Solid Wire Patch Cables

• P568-Series High-Speed HDMI Cables

To achieve maximum distance and performance, use 24 AWG solid wire Cat5e/6 cable. Using stranded wire Cat5e/6 cable, or cable with a gauge (AWG) size higher than 24 AWG, will result in shorter extension distance. Higher gauge cabling, such as 26 AWG, has a more limited transmission capability than lower gauge cabling. All Tripp Lite N202-Series Cat6 cables are made with 24 AWG solid wire cabling.

Before beginning, please note the following:

• Test to ensure the entire installation works properly before pulling cables through ceilings/walls.

• The B126-002 and B126-004 local units are set to transmit a stereo audio signal by default. Press the Audio button on the B126-002 or B126-004 to switch to 7.1-channel surround-sound audio.

• The installation procedure below describes using a B126-004 local transmitter unit. The B126-002 installation is the same except there are only two remote ports and no local monitor port.

Follow these steps for installation:

1. Make sure the HDMI source is powered OFF.

2. Connect the HDMI source to the INPUT port on the B126-002 or B126-004 using a Tripp Lite P568-Series HDMI Cable.

3. Optional for B126-004: Connect an HDMI monitor to the LOCAL port on the B126-004 using a Tripp Lite P568-Series HDMI Cable.

4. Connect the external power supply to the B126-002 or B126-004 local unit and plug it into a Tripp Lite Surge Protector, PDU or UPS. The green RJ45 LEDs and the red Power LED on the B126-004, and the green RJ45 LEDs on the B126-002 will illuminate to indicate power is being received from the external power supply.

5. Using Cat5e/6 cable, connect one of the RJ45 output ports on the local unit to the RJ45 input port on the TRIPP LITE B126-1A0-WP-1 remote unit.

6. Repeat step 5 for each additional remote unit being connected.

7. Connect the external power supply to the TRIPP LITE B126-1A0-WP-1, and plug it into a Tripp Lite Surge Protector, PDU or UPS. The green and orange LEDs illuminate, with the green LED indicating the unit is receiving power from the external power supply, and the orange LED indicating the unit is connected to a powered ON local unit via Cat5e/6 cable.

8. Repeat step 7 for each additional TRIPP LITE B126-1A0-WP-1 in the installation.

9. Connect the TRIPP LITE B126-1A0-WP-1 to a monitor using a Tripp Lite P568-Series HDMI Cable.

10. Repeat step 9 for each additional monitor being connected.

11. Turn on the power to the HDMI source. The orange RJ45 LEDs illuminate on the B126-002 and B126-004 to indicate the unit is receiving a signal from the source. The screen should now be displayed on the connected monitors.

12. If necessary, use the Equalization control on the TRIPP LITE B126-1A0-WP-1 to adjust the video image.

Before installation, note the following:

• Test to ensure the entire installation works properly before pulling cables through ceilings/walls.

• The B126-002 and B126-004 local units are set to transmit a stereo audio signal by default. Press the Audio button on the local unit to switch to 7.1-channel surround-sound audio.

• The installation diagram shows the B126-004. The B126-002 installation will be the same, except there are only two remote ports and there is no local monitor port.

Follow these steps for installation:

1. Make sure the HDMI source is powered OFF.

2. Connect the HDMI source to the INPUT port on the B126-002 or B126-004 using a Tripp Lite P568-Series HDMI Cable.

3. Optional for B126-004: Connect a local monitor to the LOCAL HDMI port using a Tripp Lite P568-Series HDMI Cable.

4. Connect the external power supply to the local unit and plug it into a Tripp Lite Surge Protector, PDU or UPS. The green RJ45 LEDs illuminate to indicate power is being received from the external power supply. An additional Red LED on the B126-004 also illuminates to indicate power is being received.

5. Using Cat5e/6 cable, connect one of the RJ45 output ports on the local unit to the RJ45 input port on the B126-110 remote/repeater unit.

6. Connect a monitor to the HDMI OUTPUT port on the remote/repeater unit using a Tripp Lite P568-Series HDMI Cable.

7. Connect the external power supply to the remote/repeater unit and plug it into a Tripp Lite Surge Protector, PDU or UPS. The green power LED and the Green RJ45 LEDs illuminate to indicate the unit is receiving power.

8. To connect additional remote/repeater units (up to four units can be daisy-chained), use Cat5e/6 cable to connect the RJ45 OUTPUT port on the first remote/repeater unit to the RJ45 INPUT port on a second remote/repeater unit.

9. Connect a monitor to the HDMI OUTPUT port on the remote/repeater unit that you just added using a Tripp Lite P568-Series HDMI Cable.

10. Connect the external power supply to the new remote/repeater unit and plug it in.

11. To add a third remote/repeater unit, repeat steps 8 through 10.

12. To finish your installation, use Cat5e/6 cable to connect the RJ45 OUTPUT port on the last remote/repeater unit to the RJ45 INPUT port on a TRIPP LITE B126-1A0-WP-1 remote receiver unit.

13. Connect a monitor to the HDMI OUTPUT port on the TRIPP LITE B126-1A0-WP-1 remote receiver unit using a Tripp Lite P568-Series HDMI Cable.

14. Connect the external power supply to the TRIPP LITE B126-1A0-WP-1 and plug it in. The green LED illuminates to indicate it is receiving power, and the orange LED illuminates to indicate it is connected to a powered ON remote/repeater unit.

15. Repeat steps 5 through 14 for each additional RJ45 output port on the local transmitter unit.

16. Turn on the power to the HDMI source. The orange RJ45 LEDs on the local unit illuminate to indicate a signal is being received from the source.

17. If necessary, use the Equalization control on the remote/repeater unit(s) and the TRIPP LITE B126-1A0-WP-1 to adjust the video image.

Before beginning, note the following:

• Test to ensure the entire installation works properly before pulling cables through ceilings/walls.

• The B126-004 is set to transmit a stereo audio signal by default. Press the Audio button on the B126-004 to switch to 7.1-channel surround-sound audio.

• Using the TRIPP LITE B126-1A0-WP-1, a 1080i (60 Hz) signal can be extended up to 200 ft. from the source, or a 1080p (60 Hz) signal up to 150 ft. from the source.

Follow these steps for a daisy-chain installation (B126-004 only):

1. Make sure the HDMI source is powered OFF.

2. Connect the HDMI source to the INPUT port on the B126-004 using a Tripp Lite P568-Series HDMI Cable.

3. Connect the LOCAL port on the B126-004 to the INPUT port on a second B126-004 using the included 1 ft. HDMI daisy-chain cable.

4. Repeat step 3 if connecting a third B126-004.

5. Optional: Connect a local monitor to the LOCAL HDMI port of the last B126-004 using a Tripp Lite P568-series HDMI cable.

6. Connect the external power supply to the first B126-004 in the daisy-chain and plug it into a Tripp Lite Surge Protector, PDU or UPS. The green RJ45 LEDs and the red Power LED on the B126-004 will illuminate to indicate power is being received from the external power supply.

7. Repeat step 6 for each additional B126-004 in the daisy chain.

8. Using Cat5e/6 cable, connect one of the RJ45 output ports on the local unit to the RJ45 input port on a TRIPP LITE B126-1A0-WP-1 remote unit.

9. Repeat step 8 for each additional remote unit being connected.

10. Connect the external power supply to the TRIPP LITE B126-1A0-WP-1, and plug it into a Tripp Lite Surge Protector, PDU or UPS. The green and orange LEDs illuminate, with the green LED indicating the unit is receiving power from the external power supply and the orange LED indicating the unit is connected to a powered ON local unit via Cat5e/6 cable.

11. Repeat step 10 for each additional TRIPP LITE B126-1A0-WP-1 in the installation.

12. Connect the TRIPP LITE B126-1A0-WP-1 to a monitor using a Tripp Lite P568-Series HDMI Cable.

13. Repeat step 12 for each additional monitor you are connecting.

14. Turn on the power to the HDMI source. The orange RJ45 LEDs illuminate on the B126-004 to indicate the unit is receiving a signal from the source. The screen should now be displayed on the connected monitors.

15. If necessary, use the Equalization control on the TRIPP LITE B126-1A0-WP-1 to adjust the video image.

If the monitor is not displaying a picture, you may need to adjust the Equalization control on the TRIPP LITE B126-1A0-WP-1 (and any remote/repeater units in the chain). An improper Equalization setting can cause the monitor not to display a picture at all. Try each Equalization setting until an acceptable picture is displayed.