TOSHIBA AW-M801AS (01) PDF MANUAL

Do not wash, spin, or dry water-proof seats, mats, or clothing.

Do not wash thick, hard mats even if the washer mark is on the care label. This may result in injury or damage to the washer, walls, floor, or clothing due to abnormal vibrations.

The accumulated water shall be drained out of the machine.

Handle the machine carefully. Never hold protruding parts of the machine while lifting.

This appliance is heavy, it should be transported carefully.

Before washing the clothes for the first time, the product shall be operated without clothes using tub clean as the recommended program.

Flammable and explosive or toxic solvents are forbidden. Gasoline and alcohol etc. Shall not be used as detergents. Please only select the detergents suitable for washing machine, especially for top-loading fully automatic washing machines.

Make sure that all pockets are emptied. Sharp and rigid items such as coins, brooches, nails, screws or stones etc. may cause serious damage to this machine.

1. Remove the cardboard box and styrofoam packing.

2. Lift the washing machine and remove the base packing.

3. Remove the tape securing the power supply cord and drain hose.

4. Pick up the inlet hose from the drum.

Do not operate the washing machine with the base packing still intact with the unit. It will cause damage to the machine.

Lean the washing machine backward at a specific angle, then insert the cabinet base cover into washing machine base trough, push it to the end.

Fix the cabinet base cover and cabinet base with all screws coming with the machine.

Running the machine or washing while placing on the bottom foam is strictly forbidden.

1. Check if the feet are properly attached to the cabinet. If not, please rotate them to their original position and tighten the nuts.

2. Check alignment of the product with a leveler and do the succeeding steps if necessary.

3. Loosen the lock nut and rotate the foot either clockwise or counter clockwise, until it closely contacts with the floor.

4. Assure that the lock is secure and then alternately press the four top corners of the machine, to check if the proper adjustment has been done.

The lock nuts on two feet must be screwed tightly against the housing.

1. Loosen clamp nut to show 5mm groove.

2. Loosen four screws.

3. Set connecting base on tap and tighten screws evenly.

4. Tighten clamp nut.

5. Press slide bushing, insert inlet hose into connecting base.

6. Connection finished.

7. After connection and installation, check if there is water leakage.

To prevent leakage or water damage, follow the above-mentioned instructions! Do not kink, crush, modify or cut the water inlet hose.

Connect the inlet hose directly to the tap with threads.

To prevent leakage or water damage, follow the above-mentioned instructions! Do not kink, crush, modify or cut the water inlet hose.

1. Plug in.

2. Open tap.

3. Put clothes in the drum.

4. Add detergent and close lid.

Before washing, please make sure that the unit is installed properly.

Before washing for the first time, the washing machine shall be operated without clothes using tub clean as the displayed course on the control panel.

Do not use water with temperature over 50° C.

In the case of Liquid detergent, it is used by this case.

1. Power On (Turns the unit on and off).

2. Select Course (Available according to the laundry type).

3. Start up (Press this button to start or Hold the washing cycle).

Water level can be selected manually.

Before washing, please check the clothes labels and the detergent usage instructions. Use low-density detergent before wash suitable for washing machines.

Check the label.

Take items out of the pockets.

Tie tassels into Knot, fasten zippers and buttons.

Put small clothes into a laundry net.

Turn the following clothes inside out those that easily form fiber on its surface and those with long strands of fiber.

Segregate clothes with varying textures or materials.

Washing a single piece of clothing may cause, severe unbalance and consequently sound an alarm. In this case, it is suggested to add one or two more pieces of clothing to the wash load that will also make spinning smoother.

Do not wash clothes stained with kerosene, touching gasoline, alcohol and other flammable materials.

As for powder detergent that can form into clusters or masses, it is suggested to dilute the detergent with some water, before pouring into the detergent box, this will prevent the inlet of the detergent box from clogging and water from over flowing during the filling process.

Choose the suitable type of detergent for the various washing temperature to get the best washing effect with less water and energy consumption.

The washing machine will select the water level automatically according to the load weight.

1. When there’s water in the tub, this function is not available.

2. Before pressing [Start/Hold] button, if the user selected the water level, there will be no fuzzy weighting function.

3. After pressing [Start/Hold] button, the washing machine will run the fuzzy weighting function.

REGULAR, JEANS, MEMORY, HEAVY WASH Course has fuzzy weighting function.

Select the water level according to clothing categories, degree of soiling and washing habits of users.

Washing time, number of rinses, spinning time and other settings can be selected.

1. Select a course.

2. Press the Preset button to choose the start time before operation starts.

3. Press [Start/Hold] to commence the Preset operation.

Press the [Preset] button repeatedly, to see Preset time choices, the Preset time should be set before starting the course. If you want to set the Preset time, after the course has already started, the on/off button should be pressed to reset the course.

If there is any interruption in the power supply while the machine is operating, a special memory stores the selected program and recalls the memory setting when the power is restarted.

To activate CHILD PROOF press the two buttons at the same time.

If this mode is set to ON and the lid opened during operation, the buzzer beeps, the indicator flashes, the washer stops water supply and stops wash/spin operation, and drains water from wash tub approximately 20 seconds of the lid opening.

The “CHILD PROOF” will lock all buttons except [On/Off].

The user can select washing course according to the actual need, and set washing time, number of rinses, spinning time, water volume and course start time.

The general flow is: ON/OFF -> Course -> Water Level -> Process/Set -> Preset -> Start/Hold.

The user can set a single process or combinations of washing, rinsing and spinning freely according to the need. The detailed operations are as follows:

For Soak, Wash, Rinse, or Spin processes:

1. Press ON/OFF.

2. Press the PROCESS button.

3. Press the SET button to set the desired time/times.

4. Press START/HOLD.

You can choose the following parameters:

SOAK: 0, 10, 20, 30, 40, 50, 60 minutes

WASH: 15-20 minutes

RINSE: 1-4 times

SPIN: 1-9 minutes

This is just for reference.

1. Add softener to the softener case at the top of the basket.

2. The Softener automatically flow into the basket during the final rinse.

3. The amount of softener varies with the brands. Follow the instruction on the softener label.

If the concentrated softener is used, dilute it with water one third of its original concentration before pouring it into the insertion case.

You cannot see the softener poured into the dispenser while rinsing. Because it moves to the three parts in the case for using the centrifugal force at spinning.

Do not open the lid while spinning. The softener dispensation timing will be thrown off and effectiveness reduced.

Before your maintenance starts, please unplug the machine and close the tap.

Proper maintenance of the washing machine can extend its working life. The surface can be cleaned with diluted non-abrasive neutral detergents when necessary. If there is any water overflow, use a wet cloth to wipe it off immediately. No sharp items are allowed.

Formic acid and its diluted solvents or equivalent are forbidden, such as alcohol, solvents or chemical products, etc.

Inlet filter must be cleaned if pressure of water from the inlet drops.

1. Close the tap.

2. Remove water inlet hose and filter from the tap.

3. Disassembly and clean the filter.

4. Reconnect the water inlet hose.

Inlet filter must be cleaned if pressure of water from the inlet drops.

1. Screw off the inlet pipe from the back of the machine.

2. Pull out the filter with a pair of long nose pliers and reinstall it back after being washed.

3. Use a brush to clean the filter.

4. Reconnect the inlet hose.

There is a built-in lint filter in your washer. It can help to collect lint during washing cycle.

It is suggested to clean the lint filter every 10 cycles.

Take it out and clean the filter with water. Then place it back into the washer.

Check if the power is off.

Check if the water volume reached the required water level. (The washer will not work if the water amount does not reach the required water level).

Check if it is set to “Preset” washing mode. (It will only start to work until the reservation time is reached).

Check if the power is off or the fuse is burned out.

Check if the water supply is cut off or the water pressure is too low.

Check if the inlet hose is properly connected and the water tap is opened.

Check if the filtering screen of inlet valve is blocked by dirt.

Check if the “Start / Hold” button is pressed after the power switch is pressed.

Check if the end of the water drain hose is placed very high.

Check if the end of water drain hose is immersed in and blocked by a pool of water.

Check if the glass lid is not closed.

Check if most of the clothing are at one side of the drum or if too many clothes are loaded in the machine.

Check if the washer is not placed in stable condition or it is placed an inclined state. (The ground is not flat).

E1 means alarm for abnormal water filling.

Check if the water tap is opened or not.

E2 means alarm for water unfinished water draining.

Check if the end of the drain hose is placed too high, if it is immersed in and blocked.

E3 means alarm for lid that is not closed before wash and spin.

Close the lid, press “Start” button.

E4 means unbalanced wash load during spinning.

Evenly distribute the clothes in the drum by hand.

E7-1, E7-2, E7-3, E7-4, E7-5 means abnormal behavior with dangerous fault (brake wires, brake, sensors).

If E7-1, E7-2, E7-3, E7-4, E7-5 appears after pressing the power button, please call for service.

If E7-1, E7-2, E7-3, E7-4, E7-5 appears during the operation, press the power button to stop the machine.

Try to look for solutions first then call for service, if no solutions work.

Do not perform any operation not mentioned in the above.

Use for model AW-M801AS, AW-M901BS Singapore model.

SPEED Course, “SET” 1 time, then “WATER LEVEL” 1 time, then “PROCESS” 2 times.