Free English SUPERMICRO SUPERSERVER SYS-E100-12T-H (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD SUPERMICRO SUPERSERVER SYS-E100-12T-H (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What are the system features of the SUPERMICRO SUPERSERVER SYS-E100-12T-H?
| Motherboards | X12STN-H/E/L/C-WOHS |
| Chassis | CSE-E101-03 |
| Processor Support | 11th Generation Intel® Core™ or Celeron® processor |
| Memory | Two DIMM slots support up to 64GB unbuffered, non-ECC SO-DIMM, DDR4-3200 |
| Expansion Slots | Three M.2 slots (one B-key, one M-key, one E-key) |
| I/O Ports | Two 2.5GbE LAN ports Two HDMI ports (one 2.0b port and one 1.4b port) One HD audio header for mic-in, line-out) Four serial ports Three USB 3.2 Gen 1 ports, one USB-C 3.2 port, four USB 2.0 ports |
| Power | Lockable 12V, 84W DC power adapter |
| Form Factor | 3.5″ SBC; 7.68″ x 1.73″ x 5.94″ (195 x 44 x 150mm) (WxHxD) |
What are the different system configurations for the SUPERMICRO SUPERSERVER SYS-E100-12T-H?
| System Model | Motherboard | CPU Support |
|---|---|---|
| SYS-E100-12T-H | X12STN-H-WOHS | 11th Generation Intel Core™ i7-1185GRE |
| SYS-E100-12T-E | X12STN-E-WOHS | 11th Generation Intel Core™ i5-1145GRE |
| SYS-E100-12T-L | X12STN-L-WOHS | 11th Generation Intel Core™ i3-1115GRE |
| SYS-E100-12T-C | X12STN-C-WOHS | 11th Generation Intel Celeron® 6305E |
What are the jumpers and descriptions on the board of the SUPERMICRO SUPERSERVER SYS-E100-12T-H?
| No. | Jumper & Description |
|---|---|
| 1 | JHDMI2: Manufacturing Mode |
| 2 | FAN1: System Fan Header |
| 3 | JLCDPWR1: LVDS Panel VCC Power Source Selection |
| 4 | LVDS1: Dual Channel 48-bit LVDS Connector |
| 5 | JCOM1: COM1/COM2 Header |
| 6 | JCOM2: COM3/COM4 Header |
| 7 | JPH1: 4-pin HDD Power Connector |
| 8 | I-SATA0: SATA 3.0 Port |
| 9 | AUDIO FP: Front Panel Audio Header (Mic-In/Line-Out) |
| 10 | USB2/3: Front Accessible USB 2.0 Headers |
| 11 | USB0/1: Front Accessible USB 2.0 Headers |
| 12 | JF1: Front Control Panel Header |
| 13 | JGP1: 8-bit General Purpose I/O Header |
| 14 | BT1: Onboard Battery |
| 15 | LAN1: 2.5 GbE Ethernet Ports |
| 16 | LAN2: 2.5 GbE Ethernet Ports |
| 17 | USB4/5: Front Accessible USB 2.0 Headers |
| 18 | USB6/7: Front Accessible USB 2.0 Headers |
What are the features of the front chassis on the SUPERMICRO SUPERSERVER SYS-E100-12T-H?
| Item | Features | Description |
|---|---|---|
| 1 | ANTENNA | WiFi antenna |
| 2 | LAN Ports | 2.5GbE LAN ports (Intel I225-IT) |
| 3 | HDMI Ports | Left port: HDMI 2.0b (4K60Hz), Right port: HDMI 1.4b |
| 4 | USB Ports | USB 3.2 ports, lower left port is USB C port |
| 5 | Power Button | System on/off button |
| 6 | Power LED | Indicates power is being supplied to the system. |
| 7 | HDD LED | Indicates data is being written to the storage drives |
What are the features of the rear chassis on the SUPERMICRO SUPERSERVER SYS-E100-12T-H?
| Item | Features | Description |
|---|---|---|
| 1 | 12V DC Input | Power input for system |
| 2 | GPIO Port | General Purpose Input/Output Port |
| 3 | COM Ports | COM1 and COM2: RS232/422/485 serial ports COM3 and COM4: RS232 serial ports |
| 4 | USB Ports | USB 2.0 ports |
| 5 | Mic-In | Microphone jack (optional) |
| 6 | Line-Out | Line out jack for audio (optional) |
How do I access the SUPERMICRO SUPERSERVER SYS-E100-12T-H system by removing the bottom cover?
1. Remove power from the system.
2. Remove the eight screws that hold the cover in place.
3. Lift the cover up and off the chassis.
How do I install the mounting brackets on the SUPERMICRO SUPERSERVER SYS-E100-12T-H?
1. Turn the chassis over to the bottom side.
2. Decide whether the bracket mounting holes will face outwards or inwards.
3. The mounting bracket supports two screw alignments. Decide which screw holes will be used.
4. Align the screw holes on the mounting bracket with the screw holes on the chassis.
5. Install two screws.
6. Repeat on the other mounting bracket.
What are the I/O Connectors for the SUPERMICRO SUPERSERVER SYS-E100-12T-H?
| No. | Description | No. | Description |
|---|---|---|---|
| 1 | LAN1 | 5 | USB5 Type C (3.1) |
| 2 | LAN2 | 6 | USB6/7 (3.1) |
| 3 | HDMI 2.0 Port | 7 | HDMI 1.4 Port |
| 4 | USB4 (3.1) |
What are the safety precautions I should take when operating the SUPERMICRO SUPERSERVER SYS-E100-12T-H?
SAFETY INFORMATION: See installation instructions and safety warning before connecting the system to the power supply.
WARNING: To reduce the risk of electric shock/damage to equipment, disconnect power from the server by disconnecting all power cords from electrical outlets. If any CPU socket is empty, install the protective plastic CPU cap.
WARNING: Always be sure all power supplies for this system have the same power output. If mixed power supplies are installed, the system will not operate.
What do the BIOS Beep (POST) Codes indicate on the SUPERMICRO SUPERSERVER SYS-E100-12T-H?
| Beep Code | Description |
|---|---|
| 1 beep | Circuits have been reset (Ready to power up) |
| 5 short, 1 long | No memory detected in system |
| 5 long, 2 short | Video adapter missing or with faulty memory |
| 1 long continuous | System overheat condition |
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
CLICK HERE TO DOWNLOAD SUPERMICRO SUPERSERVER SYS-E100-12T-H (01) PDF DOCUMENT