SUNBEAM SR4400 (01) PDF DOCUMENT

When using your SUNBEAM SR4400, please adhere to the following safety precautions:

• Do not leave a hot iron within reach of children. If they come into contact with a hot iron it could lead to serious burns.

• Iron only on an ironing board.

• An iron takes approximately 30 minutes to cool down. Allow the iron to cool completely before storing.

• Do not wind the cord around the soleplate while the iron is still hot.

• Do not leave the iron unattended while it is plugged into the power outlet.

• Always unplug the iron from the power outlet before filling or emptying the water tank.

• The iron must be used and rested on a stable surface.

• When placing the iron on its heel, ensure that the surface on which the stand is placed is stable.

• The iron is not to be used if it has been dropped, if there are any visible signs of damage or if it is leaking.

The following precautions are essential for the safe use of your SUNBEAM SR4400:

• Read carefully and save all the instructions provided with an appliance.

• Always turn the power off at the power outlet before you insert or remove a plug. Remove by grasping the plug – do not pull on the cord.

• Turn the power off and remove the plug when the appliance is not in use and before cleaning.

• Do not use your appliance with an extension cord unless this cord has been checked and tested by a qualified technician or service person.

• Always use your appliance from a power outlet of the voltage (A.C. only) marked on the appliance.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that they do no play with the appliance.

• The temperature of accessible surfaces may be high when the appliance is operating.

• Never leave an appliance unattended while in use.

• Do not use an appliance for any purpose other than its intended use.

• Do not place an appliance on or near a hot gas flame, electric element or on a heated oven.

• Do not place on top of any other appliance.

• Do not let the power cord of an appliance hang over the edge of a table or bench top or touch any hot surface.

• Do not operate any electrical appliance with a damaged cord or after the appliance has been damaged in any manner. If damage is suspected, return the appliance to the nearest Sunbeam Appointed Service Centre for examination, repair or adjustment.

• For additional protection, Sunbeam recommend the use of a residual current device (RCD) with a tripping current not exceeding 30mA in the electrical circuit supplying power to your appliances.

• Do not immerse the appliance in water or any other liquid unless recommended.

• Appliances are not intended to be operated by means of an external timer or separate remote control system.

• This appliance is intended to be used in household and similar applications such as: staff kitchen areas in shops, offices and other working environments; farm houses; by clients in hotels, motels and other residential type environments; bed and breakfast type environments.

Your SUNBEAM SR4400 Pro Steam Iron includes the following features:

Vertical shot of steam: Pressing the shot of steam button with the iron in an upright position produces a vertical shot of steam, ideal for steaming curtains, suits, and removing creases from delicate fabrics.

Powerful shot of steam: Pressing the shot of steam button instantly produces a powerful shot of steam to remove stubborn wrinkles.

Fine spray mist: Pressing the spray button provides a fine mist spray to dampen hard-to-iron fabrics.

Variable steam: Allows you to select the desired steam output. Alternatively, select the ‘0’ setting to iron without steam.

Easy-fill water inlet: The water inlet cover opens fully to allow easy filling of the water tank without bubbling or spilling.

Precision Tip: A narrower tip to reach areas such as pleats and buttons.

Large water tank: Holds 300ml of water for continual high steam performance without having to refill the tank regularly.

Full length button groove: Designed for easy ironing around buttons.

EasyGlide Non-stick soleplate: Glides easily across all fabric for quick and easy ironing.

Anti Drip: Helps avoid water marks.

Anti Calc System: Prevents scale build-up for better performance and a longer lasting iron.

Safety auto-off: The iron automatically switches itself off if left in the ironing position (horizontal) for 30 seconds, or in the heel rest position (vertical) for 15 minutes.

Long cord with 360° cord outlet: Ideal for left or right-hand use, providing greater versatility and ease of movement. The flexible grommet protects the cord from fraying.

Thermostat light: Illuminates to indicate the iron is heating and goes out when it has reached the selected temperature. It cycles on and off during ironing to maintain the temperature.

Temperature dial: Allows you to select the desired temperature for each garment and indicates the amount of steam recommended for each setting.

Self-Clean Button: Helps to flush out impurities to prevent spotting on garments.

Stable heel rest: A large heel rest keeps the iron stable on the ironing board.

Cord wrap facility: A built-in feature to wind the cord around the heel for neat storage.

2400 watts: Provides fast heat-up, a higher pressure steam shot, quicker heat recovery, and an even temperature.

Before first use, remove any adhesive stickers, plastic covers or cardboard sleeves from the soleplate. Ensure that all adhesive is removed by rubbing the soleplate with a cloth dampened with methylated spirits.

Fill the water tank and empty the water. This will rinse out any foreign particles remaining in the water tank from the manufacturing process.

NOTE: When turned on for the first time, your new SUNBEAM SR4400 iron may give off vapours for up to 10 minutes. This is due to the initial heating of the materials used. It is safe and not detrimental to the performance of the iron.

Before filling the iron with water, ensure the power is turned off and the plug is removed from the power outlet. The iron can be filled with water while it is hot.

Slowly pour water into the water inlet until the maximum water level is reached. Do not exceed the maximum water level indicator. Push the water inlet cover firmly to close.

NOTE: The special soleplate design allows you to use tap water with your SUNBEAM SR4400 iron without affecting the steam performance. However, in very hard water areas, Sunbeam recommends the use of distilled water or water which has been demineralised.

Do not fill the iron with fabric conditioner, starches or any other solution as these will damage the steam mechanism. Do not use contaminated water.

1. Insert the plug into a 230/240 volt power outlet and turn the power on.

2. Turn the temperature dial to the desired setting by aligning the setting on the dial with the temperature indicator. The thermostat light (positioned on the top of the handle) will illuminate to indicate that the iron is heating to the selected temperature. When the thermostat light goes out the iron has reached the selected temperature and is ready to iron.

NOTE: When the temperature dial is changed from a high setting to a lower temperature setting during ironing, the thermostat light will go out immediately. This indicates that the iron is cooling to the selected temperature. To ensure that the iron has reached the selected temperature and is not too hot, wait until the thermostat light comes on again and then goes out before ironing.

NOTE: When steam ironing, ensure that the temperature dial is set to any temperature within the steam band and that the tank is at least 1/4 full of water.

The shot of steam can be used for both dry or steam ironing when the temperature dial is set to any temperature above the two dot (••) setting.

1. Ensure the tank is at least ¼ full of water.

2. Select the desired temperature and wait until the thermostat light goes out.

3. Press the shot of steam button several times with the iron on the soleplate to prime the pump.

NOTE: If the tank has run dry, it may be necessary to re-prime the pump after filling the iron with water.

The spray mist can be used for both dry or steam ironing to pre-dampen hard to iron fabrics.

1. Ensure the tank is at least ¼ full of water.

2. Press the spray button during ironing to release a fine mist from the spray nozzle.

The safety auto-off mechanism on your SUNBEAM SR4400 automatically turns the iron off if you forget.

The iron will automatically shut off if left on the heel rest (vertical) for 15 minutes, or in the ironing position (horizontal) for 30 seconds, without being moved.

The safety auto-off light on the handle will flash and a warning beep will sound to let you know that you have left the iron unattended. The power to the iron’s heating element will be cut.

Once the iron is moved, the power will reconnect. Allow the iron to heat until the thermostat light goes out, and continue ironing as normal.

After each use:

1. Turn the power off and remove the plug from the power outlet.

2. Allow the iron to cool before winding the cord around the built-in cord wrap.

Storage:

Always store the iron on its heel rest.

NOTE: Do not store the iron with the soleplate facing down, or in the carton.

Cleaning the Exterior:

To clean the exterior of your iron, wipe over with a damp soft cloth and wipe dry.

Caution: Do not use harsh abrasives, chemical cleaners or solvents to clean the exterior of your iron as these will damage the surface.

To clean the steam holes:

To remove build up from the steam holes which may affect steam performance, use a cotton wool tip moistened in methylated spirits.

Cleaning the EasyGlide™ non-stick soleplate:

The non-stick coating reduces sticking of fabrics and starches to the soleplate. Do not iron over sharp objects such as buttons, studs and zippers, as these will scratch the surface.

Wipe the soleplate with a damp soft cloth after each use. If polyester has burnt to the soleplate, iron a damp cotton cloth while hot.

Caution: Do not use scouring pads, abrasives or harsh cleaners to clean your EasyGlide non-stick soleplate, as these may scratch and damage the surface.

Self-Clean Button:

The self-clean button helps to flush out impurities to prevent spotting on garments. Press the button to flush water through the iron.

Tip # 27 – Iron shirts like a pro: Start with the collar, working from the outer edges into the middle. Iron the shoulder next, followed by the cuffs and sleeves. Place the collar at the narrow end of the board so that one front panel of the shirt is extended flat. Iron the front panel from shoulder to shirt tail. Rotate to iron the back of the shirt. Rotate and complete the remaining front panel.

Tip # 34 – Tips for T-shirts: Straighten seams on t-shirts before hanging out to dry. To avoid damage to printed graphics and logos turn the t-shirt inside out and iron the reverse side of the print. Never iron areas of your t-shirt where perspiration marks are visible as the heat of the iron will permanently fix the stain.

Tip # 54 – Hung out to dry: When washing is complete, remove shirts from the machine immediately, shake them out and hang them on coat hangers to air dry – this will keep wrinkles to a minimum.

Tip # 18 – Selecting the right temperature: If you are unsure of the correct setting for a particular garment, test a small area such as a seam or inside hem before ironing a visible area. Start with a low temperature and slowly increase the heat to find the best setting.

Tip # 33 – Don’t be afraid to iron silk: Although delicate in appearance, silk is the strongest and most resilient of all natural fibres. To achieve the best results, set to a low cotton setting and use regular shots of steam. Always use a pressing cloth to avoid shine marks.

Tip # 13 – Ironing the seam: Always press seams in the same direction they were made. When a garment is produced, the fibres will naturally settle in the direction they were initially pressed, so it’s best not to iron against the grain.

Tip # 26 – Sort types of fabric: Sort articles to be ironed according to the type of fabric. This will reduce the need to adjust the temperature constantly. Start with articles requiring lower temperatures and work your way through to items requiring higher settings.

Tip # 2 – Summer frocks and frills: Steam is the key when ironing delicate summer fabrics such as muslin, cotton and linen. Don’t press down with the iron, simply hover above the garment and steam it using a vertical shot of steam. Ruffling, netting, tulle or intricate hand detailing is also best ironed using this method.

Tip # 5 – Pressing your winter woollies: Steam is crucial when pressing your winter woollies. Woollen garments can be hung and steamed using the vertical shot of steam feature. After steaming, brush the garment with your hand to plump up woollen fibres. If ironing the garment flat it is best to use a pressing cloth. Don’t be afraid to apply pressure – steam and hold.

Tip # 42 – Table settings to impress: To avoid unwanted creases always iron your table cloth after taking it out of the cupboard. For best results, lay towels across your table and iron the table cloth over the towels. This will save you time and ensure a beautifully presented table setting.