Free English STARTECH MCM10GSFP (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD STARTECH MCM10GSFP (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What are the descriptions for the front view components of the STARTECH MCM10GSFP?
| Port/LED | Function |
|---|---|
| 1 SFP+ Slot | Connect an SFP+ to the Media Converter. |
| 2 LEDs |
Link Solid Green: Link speed of 10G Power Solid Green: Media Converter is receiving power. |
| 3 RJ45 Port | Connect an Ethernet Network Device to the Media Converter. |
What is the description for the rear view component of the STARTECH MCM10GSFP?
| Port/LED | Function |
|---|---|
| 4 5V DC Port | Connect the Universal Power Adapter to power the Media Converter. |
How do I install and connect the STARTECH MCM10GSFP?
1. Turn off the Networking Equipment that will be connected to the Media Converter.
2. Remove the Dust Cover from the SFP+ Slot.
3. Insert an MSA-compliant 10GbE SFP+ module (sold separately) into the SFP+ Slot on the Media Converter. Note: The Media Converter can only be used with 10GbE SFP+ Module.
4. Remove the Dust Cover from the SFP+ Module.
5. Connect a Fiber-Optic Cable (sold separately) to the Fiber-Optic Ports on the SFP+ Module.
6. Connect the other end of the Fiber-Optic Cable to the Fiber-Network Device. Note: For Duplex Fiber Optic Cables, the TX and RX connectors must be paired at both ends of the connection. For example TX to RX, and RX to TX.
7. Connect a Cat 6/6a Cable (sold separately) to the RJ45 Port on the Media Converter.
8. Connect the other end of the Cat 6/6a Cable to the Ethernet Network Device.
Warning: There may be a delay (up to 10 seconds) establishing a network connection when connecting the Media Converter to a Network Device.
How do I power the STARTECH MCM10GSFP and check the connection?
1. Connect the Universal Power Adapter to the 5V DC Port on the Media Converter.
2. Connect the other end of the Universal Power Adapter to an AC Electrical Outlet. The PWR LED (power) should light up solid green.
3. Turn the Networking Equipment from step #1 back on.
Note: Check the link budget of your SFP+ modules, as well as the module’s intended wiring distance. SFP+ modules are designed to transmit signals over large distances. If the physical wiring distance is too short, the transmitting optical signal (laser) may be too strong and damage the receiving SFP+ module. An in-line optical attenuator may be required to protect it from damage.
What are the network specifications regarding duplex mode and distance for the STARTECH MCM10GSFP?
Duplex Mode Support
The Media Converter’s RJ45 Port supports 10G and will automatically negotiate the connection type. By default, it will automatically detect the link speed and the duplex mode of your connected equipment.
The Media Converter’s Fiber-Optic Port (1000Base-LR/SR) allows 10G full duplex auto-negotiation. Check to ensure the duplex setting of the connected fiber equipment matches the duplex setting of the Media Converter.
Distance Capabilities
The distance capabilities of the Media Converter are variable and depend on the SFP+ Module and the Fiber-Optic Cable used.
How do I install and remove the power adapter clip for the STARTECH MCM10GSFP?
Installing the Power Adapter Clip
1. Remove the Power Adapter from the box.
2. Locate the Power Clip specific to your region (e.g. U.S.).
3. Align the Tabs on the Power Clip with the Slots on the Power Adapter so that the Contact Prongs on the Power Adapter are vertical (one above the other).
4. Rotate the Power Clip clockwise until you hear an audible click indicating that the Power Clip is properly attached to the Power Adapter.
Removing the Power Adapter Clip
While pressing the Release button turn the Power Clip counter-clockwise until the Power Clip is released.
CLICK HERE TO DOWNLOAD STARTECH MCM10GSFP (01) PDF DOCUMENT