STAPLES ST63113 (01) PDF Document

The following parts are included for the assembly of your STAPLES ST63113 chair:

Hardware:

A – Yellow Screw (x6)

B – Blue Screw (x4)

C – Green Screw (x3)

D – Yellow Screw (x2)

Components:

1 – Caster (x5)

2 – Base (x1)

3 – Gas Lift (x1)

4 – Seat Plate (x1)

5 – Seat (x1)

6 – Back (x1)

7 – Arms (x2)

8 – Headrest (x1)

Tools Provided:

E – Allen Wrench (x1)

Follow these steps to assemble your STAPLES ST63113 chair. Each piece of hardware needed for each step is located in the corresponding segment in your Easy Parts Pack.

Step 1: Insert the five Casters (1) into the holes on the Base (2).

Step 2: Insert the Gas Lift (3) into the center hole of the Base (2).

Step 3: Attach the Arms (7) to the underside of the Seat (5) using six Yellow Screws (A). Tighten with the Allen Wrench (E).

Step 4: Attach the Seat Plate (4) to the underside of the Seat (5) using four Blue Screws (B). Tighten with the Allen Wrench (E).

Step 5: Attach the Back (6) to the Seat Plate (4) using three Green Screws (C). Tighten with the Allen Wrench (E).

Step 6: Attach the Headrest (8) to the top of the Back (6) using two Yellow Screws (D). Tighten with the Allen Wrench (E).

Final Step: Place the assembled upper portion of the chair onto the Gas Lift (3). To secure the seat into the base, sit down on the chair.

The main components of the assembled STAPLES ST63113 chair are:

• Headrest

• Back

• Arms

• Seat

• Seat Plate Assembly

• Gas Lift

• Base

• Caster

To raise the seat:

1. Lean slightly forward while seated to relieve the pressure on the tilt mechanism.

2. Reach under the right side of the chair and locate the handle.

3. Raise yourself up slightly to allow the chair to reach your desired height.

To lower the seat:

Remain seated and lift the handle upwards until the chair lowers to your desired height.

1. Locate the paddle underneath the right side of the seat.

2. Push the paddle out to allow the back to tilt freely.

3. Push the paddle in to allow the back to lock in 1 of 3 preset positions.

1. Grasp the round cylinder knob under the front center of the seat.

2. For firmer/stiffer tilt, turn the knob counter-clockwise.

3. For softer/looser tilt, turn the knob clockwise.

1. Press the buttons on the chair arms to allow the arms to move up or down freely.

2. Release the buttons once the desired height is reached.

To adjust the lumbar support, slide the lumbar support piece on the back of the chair up or down to the desired location.

Headrest Angle Adjustment:

The headrest rotates forward and back by 15 degrees. Hold the headrest and rotate it forward or back to the desired angle.

Headrest Height Adjustment:

The headrest raises and lowers. Hold the back of the chair and lift the headrest up to raise it; push down to lower it.

The Seat Height Adjustment feature on your STAPLES ST63113 adjusts to assure correct posture and relieves stress on the back, thighs, and legs.

The Tilt Tension Adjustment feature on your STAPLES ST63113 allows for easy adjustment of chair flexibility, which avoids heavy pushing and relaxes muscles.

The Upright Seat Tilt Lock on your STAPLES ST63113 is a simple locking mechanism that fixes the seat in an upright position to assure healthy posture.

The arms on your STAPLES ST63113 adjust up and down or swivel to ease pressure on the neck and support the shoulders.

The Variable Tilt Lock is a locking mechanism on your STAPLES ST63113 that allows the back to lock in 3 preset positions to assure healthy posture.

The Lumbar Support Adjustment feature on your STAPLES ST63113 provides added cushioning in the chair back for maximum support to the lower back.

Chair bolts, screws and knobs may loosen during use. Please tighten your STAPLES ST63113 chair’s hardware each month.