SOKANI COLA 60C (01) PDF Document

Please follow these safety precautions when using the SOKANI COLA 60C:

• Do not look directly at the light when it is on.

• Do not place any objects on the product or let liquid flow into it.

• During use, ensure the ventilation holes are not obstructed to prevent overheating and damage. The surface temperature may be high during prolonged use, so be cautious to avoid burns.

• The device has a temperature protection feature. When the temperature is too high (>75°C), the temperature icon will flash. If it exceeds 80°C, it enters a protective state (brightness limited to 20%). It will return to normal when the temperature drops.

• This product is not waterproof. Do not use the product in water or expose it to rain.

• Do not disassemble or modify the product. If the product is damaged due to falling or other accidents, please send it to an authorized service center or manufacturer’s authorized repair center for inspection and repair.

The main parts of the SOKANI COLA 60C are identified as follows:

01. Lock Button

02. Accessory Port

03. LED Beads

04. Bead Protection Cover

05. Heat Dissipation

06. 1/4 Mounting Hole

07. LCD Color Screen

08. Power Button

09. Mode/FX Button

10. Power Interface (DC 12V-20V)

11. Power Interface (USB-C PD 3.0)

To start using the SOKANI COLA 60C, follow these steps:

1. DC Power Supply: Connect the adapter to the AC power source, then connect the adapter’s DC connector to the light’s DC port.

2. PD Power Supply: Connect the USB-C cable to a PD 3.0 charger, then connect the other end of the USB-C cable to the light’s USB-C power port.

3. Power On: Press and hold the left knob for 3 seconds to turn on. The photography light’s LCD will display the current information of the host and enter the working state.

Note: When both DC and PD are connected to the power source, the light will prioritize power from the port that was connected first.

To adjust the Correlated Color Temperature (CCT) mode, follow these steps:

1. Press the ⚫ button to enter CCT mode.

2. Rotate the 🔆 knob to adjust brightness, with an adjustable range of 0%-100%.

3. Rotate the 🎨 knob to adjust the output color temperature.

4. To adjust the green/magenta tint, press the 🎨 knob. Press it again to move the icon to the GM parameter, and then rotate the 🎨 knob to adjust the green/magenta value. After about 3 seconds, the icon defaults to adjusting brightness and saves the current parameters.

To adjust the Hue, Saturation, and Intensity (HSI) mode, follow these steps:

1. Press the ⚫ button to enter HSI mode.

2. Rotate the 🔆 knob to adjust the output brightness, with an adjustable range of 0%-100%.

3. Press the 🎨 knob to switch between different parameters. Press the 🎨 knob to move the icon to the H (Hue) parameter and then rotate the 🎨 knob to adjust the output color (0-360).

4. Press the 🎨 knob again to move the icon to the S (Saturation) parameter and then rotate the 🎨 knob to adjust the saturation (0-100). After about 3 seconds, the icon defaults to brightness mode and saves the current parameters.

To adjust the RGBCW (Red, Green, Blue, Cool White, Warm White) mode, follow these steps:

1. Press the ⚫ button to enter RGBCW mode.

2. Press the 🎨 knob, then rotate it to switch between the different beads that need adjustment.

3. Rotate the 🔆 knob to adjust the brightness of the selected beads, with an adjustable range of 0%-100%. After about 3 seconds, the icon defaults to adjusting brightness and saves the current parameters.

To use the special effects (FX) mode, follow these steps:

1. Press the ⚫ button to enter FX special effect mode.

2. Press the FX key to switch between different modes. The current special effect name will be displayed on the last line of the screen.

3. Rotate the 🔆 knob to adjust the brightness, with an adjustable range of 10%-100%.

4. Rotate the 🎨 knob to adjust the rate of the special effect. The larger the negative value, the higher the frequency. The current parameters will be saved after about 3 seconds.

The available FX modes are:

You can search for “SS LED Video Light” in the App Store and Android market to download and install the professional light control software.

To connect the SOKANI COLA 60C to the app:

1. Turn on Bluetooth on your mobile phone and turn on the SOKANI COLA 60C light.

2. Open the “SS LED Video Light” APP, click “Add Device”, and select the light you want to connect. In any mode, a flashing Bluetooth icon on the light’s LCD screen indicates that the light is in a connectable state. If the Bluetooth icon is not flashing, it means the light is already connected.

3. When the light is first turned on, it enters SET mode. The Bluetooth icon will display the unique Bluetooth code of the device, which you can use to identify and connect to the correct light in the APP.