KORG TM-60C (02) PDF MANUAL

KORG TM-60C (02) PDF SUMMARY:

How do I install the batteries?

Slide the battery compartment cover on the back of the TM-60/TM-60C and lift up the cover. Insert the batteries, making sure to observe the correct polarity, and then close the cover.

---

How do I use the internal mic?

Make sure nothing is connected to the INPUT jack.

---

How do I use the contact mic?

Plug it into the INPUT jack. The contact mic is included with the TM-60C only.

---

How do I use headphones?

Plug commercially available headphones into the (headphones) jack.

---

How do I use the stand?

Pull out the stand in order to prop up the TM-60/TM-60C.

---

How do I tune using the meter?

1. Press the TUNER ON button (Meter mode). This button turns the TM-60/TM-60C on or off.
2. Play a single note on your instrument and tune it.
3. Tune your instrument until the correct note name appears on the display and the meter indication is at the center.
4. To change the reference pitch from the default setting A4=440 Hz, press the CALIB·NOTE or button.

---

How do I tune using the tone (Sound Out mode)?

Tune your instrument to match the reference tone that is output by this device.

---

How do I tune using the tone (Sound Back mode)?

This device detects the tone that you play on your instrument and outputs the closest reference tone. Compare it with the pitch of the tone that you output and tune your instrument. Sound Back mode can be used if a device is connected to either the INPUT jack or the (headphones) jack (or both).

1. Press the TUNER ON button.
2. To use Sound Out mode, press the SOUND/SOUND BACK button. To use Sound Back mode, hold down the SOUND/SOUND BACK button. " " appears on the display.
3. Press the CALIB·NOTE or button to select a note in semitone steps between C3 and C6. If the device is in Sound Back mode, playing a single note on your instrument will output the closest reference tone.

---

How do I use the metronome?

1. Press the METRONOME ON button. This button turns the TM-60/TM-60C on or off.
2. Press the START/STOP button. The metronome starts.

---

How do I set the tempo?

• Press the TEMPO or button (30–252 beats per minute (bpm)).
• To change the tempo in steps of 1, hold down the TEMPO and buttons simultaneously to switch to Full Step, and then press the TEMPO or button.
• Otherwise, press the TAP TEMPO button several times at the tempo that you want.

---

How do I set the time signature?

Press the BEAT or button. 0 µ 1 … 9 (9 beats) µ (Quadruplet without the center beat) µ (Quadruplet) µ (Triplet without the center beat) µ (Triplet) µ (Duplet) µ 0 …

---

How do I use the tuner and metronome simultaneously?

Press the TUNER ON and METRONOME ON buttons to turn on both. The tuning meter appears in the upper part of the meter on the display, and the metronome pendulum appears in the lower part of the meter.

---

What should I do if a foreign object enters the device or if the product malfunctions?

Turn off the power immediately and consult the customer support.

---

What should I do for regular care?

• Ensure proper ventilation.
• Keep it away from radios, televisions, and electronic devices.
• Clean the exterior with a soft, dry cloth.
• Remove the batteries when not in use for an extended period.
• Keep batteries and the device out of reach of children.
• Do not expose batteries to excessive heat.
• Avoid excessive force on buttons and knobs.
• Do not use benzene, thinner, or similar liquids for cleaning.
• Do not place it in unstable locations.

---

What locations should I avoid using the unit in?

• In direct sunlight
• Locations of extreme temperature or humidity
• Excessively dusty or dirty locations
• Locations of excessive vibration
• Close to magnetic fields

---

What should I do regarding the power supply?

Be sure to turn off the power when the unit is not in use. Remove the battery in order to prevent it from leaking when the unit is not in use for extended periods.

---

How do I address interference with other electrical devices?

Radios and televisions placed nearby may experience reception interference. Operate this unit at a suitable distance from radios and televisions.

---

How should I handle the device to avoid breakage?

To avoid breakage, do not apply excessive force to the switches or controls.

---

What should I do to care for the exterior of the device?

If the exterior becomes dirty, wipe it with a clean, dry cloth. Do not use liquid cleaners such as benzene or thinner, or cleaning compounds or flammable polishes.

---

What should I do with the manual after reading it?

After reading this manual, please keep it for later reference.

---

How do I prevent foreign matter from getting into my equipment?

Never set any container with liquid in it near this equipment. If liquid gets into the equipment, it could cause a breakdown, fire, or electrical shock. Be careful not to let metal objects get into the equipment.

---

What should I do if this equipment causes harmful interference to radio or television reception?

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.