SKOPE EZICORE BCE1200N (01) PDF Document

When installing the SKOPE EZICORE BCE1200N, ensure the following requirements are met:

Ventilation: Ensure all ventilation clearances are provided as specified.

Surface: The installation surface must be capable of supporting the loaded cabinet.

Door Opening: Allow adequate space for the doors to open and close properly.

Climate Class: The fridge must be installed in an environment within its climate class, as stated on the cabinet rating label inside the fridge.

Sunlight: Do not install the fridge in direct sunlight.

Uneven Surface: Do not install the fridge on an uneven surface.

Power Supply: Do not overload the power supply.

Blocking Ventilation: Do not store boxes or items in front or on top of the fridge.

The SKOPE EZICORE BCE1200N must have the following ventilation clearances at all times:

Top: Minimum 50 mm clearance above the cabinet.

Rear: Minimum 50 mm clearance behind the cabinet. This is provided by extending the two rear spacers out and ensuring they are locked into place.

Sides: No side clearance is required.

Follow these steps to remove the sign assembly from the SKOPE EZICORE BCE1200N:

1. Disconnect the cabinet from the mains power supply.

2. Lift the sign panel to unplug the two cabinet light connectors leading from the hinge, located on each side.

3. Remove the polyethylene (PE) tape on the top of the cabinet.

4. Unplug the connector inside the plastic box.

5. Swing the sign out from the cabinet, lift it off, and place it down carefully.

6. Remove the back strip by lifting it up and off the side panels.

7. Loosen the screws holding the side panels to the top of the cabinet, then remove the side panels by sliding them backwards.

To fit a door handle on the SKOPE EZICORE BCE1200N, follow this procedure:

1. Ensure all handle components (plastic handle, counterbore hole, washer, fixing screw, and end cap) are ready for assembly.

2. Place both handle counterbore holes simultaneously onto the door frame mounting holes.

3. Fasten the fixing screws through the handle to lock the position. Note that the fixing screw is fastened through a counterbore hole, washer, and into the nut bar in the door frame.

4. Place the end caps over the screw heads to conceal the fasteners.

Caution: Ensure both handles are securely fixed to the door frames before using the fridge.

To move a shelf clip in the SKOPE EZICORE BCE1200N:

1. Unclip the metal lock by pulling it forwards.

2. To move the clip upwards, slide it to the required position.

3. To move the clip downwards, push the tab up and slide the clip down to the required position.

4. Once at the correct height, push the metal lock in to set the clip. Use the numbers on the shelf support strips to ensure all clips are at the same height.

To reposition the shelf itself, unload and remove the shelf, move the clips, then sit the shelf back on the clips and reload with product.

The SKOPE EZICORE BCE1200N temperature is factory set to stay between 0.5 degrees Celsius and 2.5 degrees Celsius. To change this range:

1. Refer to the table below to select a set number:

2. Press the set button for more than 3 seconds until the controller displays the code Po (password).

3. Press the set button again to enter password setting mode. The controller will display 00.

4. Press the Power (up) or Defrost (down) button to scroll to 55.

5. Press the set button to confirm the password. The parameter name St (setpoint) will be displayed.

6. Press the set button again. The controller will display the current setpoint default value.

7. Press the Power (up) or Defrost (down) button to increase or decrease the value based on the table above.

8. Once the required setpoint is displayed, press the set button for more than 3 seconds to store the new value and exit.

The SKOPE EZICORE BCE1200N electronic controller displays the following messages and alarms:

To replace an interior light in the SKOPE EZICORE BCE1200N:

1. Disconnect the cabinet from the mains power supply.

2. Gently remove the side and top black plastic strips with a slotted screwdriver to expose the black waterproof connector.

3. Unplug the connector and gently remove the failed light assembly using the slotted screwdriver.

4. Fit the new SKOPE OEM light assembly and plug it into the black connector.

5. Refit the side and top plastic strips.

6. Reconnect the power supply and check for correct operation.

To adjust the door tension on the SKOPE EZICORE BCE1200N:

1. Remove the split pin from the capstan at the bottom hinge.

2. Remove the tension bracket from the bottom hinge.

3. Use a tool to apply tension to the door via the capstan.

4. First, rotate the capstan against the door opening direction to remove slack. Once resistance is felt, continue to rotate 180 degrees to provide tension.

5. While holding tension on the capstan, fit the tension bracket so it supports the door tension.

6. Fit the split pin back through the hole in the capstan to lock it in place.

7. Check the tension by holding the door open about 100 mm and letting it go; it should close gently and form an airtight seal.

Regularly cleaning the condenser coil is vital for the efficient operation of the SKOPE EZICORE BCE1200N. Follow these steps:

1. Disconnect the cabinet from the mains power supply.

2. Remove the kick panel from the front of the cabinet.

3. Check the condition of the condenser coil. Use a soft brush to remove dust and fluff.

4. If a more thorough clean is needed, a service technician may perform a nitrogen blow-out or use a PH-neutral chemical clean.

5. Refit the kick panel and reconnect to the power supply.

Warning: Always unplug the cabinet from the power supply before cleaning the condenser coil.

Maintenance for the SKOPE EZICORE BCE1200N should be performed as follows:

Use the following guide to troubleshoot issues with the SKOPE EZICORE BCE1200N: