Free English SIMPSON S2700H (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD SIMPSON S2700H (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
How do I assemble the handle on the SIMPSON S2700H?
To assemble the handle on the SIMPSON S2700H, slide the handle onto the frame and secure it using the provided saddle bolt and knob.
How do I attach the nozzle to the spray wand of the SIMPSON S2700H?
Pull the quick-connect coupler back and insert the nozzle into the socket. Release the quick-connect coupler and twist the nozzle to make sure it is secure in the coupler.
What is the proper procedure for starting the SIMPSON S2700H?
Before starting the SIMPSON S2700H, ensure you have added the provided oil, as the engine is shipped without it. Connect the water hose to the water source and turn it on to remove air, then turn it off. Connect the high pressure hose to the pump outlet and the water source to the pump inlet. Turn the water source on, and depress the gun trigger to remove air from the pump and high pressure hose until a steady stream appears. Follow the engine owner’s manual for the starting procedure. If the engine does not start after two pulls, squeeze the gun trigger to relieve pump pressure, then pull the starter cord slowly until resistance is felt, followed by a rapid pull to prevent kickback.
How can I apply cleaning chemicals with the SIMPSON S2700H?
To apply chemicals with the SIMPSON S2700H, press the detergent siphon hose onto the barbed fitting located near the high pressure hose connection on the pump. Place the other end of the siphon hose, which has a filter, into your container of cleaning solution. Install the low pressure (black) nozzle into the quick connect fitting of the spray wand. After using chemicals, place the siphon hose into a container of clean water to rinse the injection system thoroughly.
How do I select the correct nozzle for the SIMPSON S2700H?
Refer to the following table to choose the correct nozzle for your job with the SIMPSON S2700H:
| Nozzle Color | Spray Pattern | Uses | Surfaces |
|---|---|---|---|
| Red | 0 degrees | Powerful pinpoint for spot cleaning of hard, unpainted surfaces or high reach areas | Unpainted metal or concrete; DO NOT use on wood |
| Yellow | 15 degrees | Intense cleaning of unpainted hard surfaces | Grills, driveways, concrete or brick walkways, unpainted brick or stucco |
| White | 40 degrees | Cleaning of painted or delicate surfaces | Auto/RV, marine, wood, painted brick and stucco, vinyl, painted siding |
| Black | Low pressure | Applies cleaning solutions | Safe on all surfaces |
How do I perform nozzle cleaning on the SIMPSON S2700H?
If the nozzle on the SIMPSON S2700H becomes clogged, shut off the unit and turn off the water supply. Pull the trigger on the gun handle to relieve any pressure. Disconnect the spray wand from the gun, remove the nozzle, and clear any obstructions using the provided cleaning tool. Backflush the nozzle with clean water, then direct the water supply into the spray wand to backflush it for 30 seconds. Reassemble and test.
How do I prepare the SIMPSON S2700H for storage?
For long term storage or freezing temperatures, the SIMPSON S2700H pump should be protected. Disconnect the spark plug wire. Connect a short length of garden hose to the water inlet of the pump. Use a funnel to add 6 ounces of RV antifreeze into the hose. Pull the starter rope slowly several times until the antifreeze comes out of the high pressure hose connection. Drain all water from the high pressure hose, spray gun, and wand. Store the unit in an upright position.
What are some general troubleshooting steps for the SIMPSON S2700H?
Refer to this table for troubleshooting the SIMPSON S2700H:
| Operational Issue | Possible Cause | Solution |
|---|---|---|
| Engine will not start | No fuel or pressure buildup | Add fuel or squeeze gun trigger to relieve pressure |
| No or low pressure | Spray wand not in high pressure, low water supply, obstructed nozzle, or air in hose | See operation section, check water supply, clean nozzle, or bleed air from hose |
| Will not draw chemicals | Spray wand not in low pressure, or chemical filter/injector clogged | Use black nozzle, clean filter, or verify siphon hose is submerged |
| Water leaking at pump | Loose connections or worn packings/o-rings | Tighten connections or contact customer service for internal component issues |
CLICK HERE TO DOWNLOAD SIMPSON S2700H (01) PDF DOCUMENT