Free English PARKSIDE PPEXS 750 B2 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD PARKSIDE PPEXS 750 B2 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What is the intended use of the PARKSIDE PPEXS 750 B2?
The PARKSIDE PPEXS 750 B2 is intended exclusively for the dry sanding of wood, metal, or paint. It must only be operated in dry areas.
How do I connect the dust extraction system to the PARKSIDE PPEXS 750 B2?
Follow these steps to connect dust extraction:
1. Insert the adapter for dust extraction into the dust ejection.
2. Slide the release of the adapter into the holder on the device. It is secured once you hear a click.
3. Connect a suitable external suction hose to the adapter for dust extraction.
4. To remove the adapter, press the release towards the adapter.
How do I replace the sanding sheet on the PARKSIDE PPEXS 750 B2?
The sanding disc is fitted with Velcro for easy attachment.
1. Before attaching, clean the sanding disc, especially the Velcro fabric, using a vacuum cleaner.
2. Place the sanding sheet onto the sanding disc.
3. Press the sanding sheet firmly onto the disc.
4. Ensure that the holes in the sanding sheet match the suction holes in the sanding disc for proper dust extraction.
How do I change the sanding disc on the PARKSIDE PPEXS 750 B2?
Use only the open-end wrench included in the delivery.
1. Turn the PARKSIDE PPEXS 750 B2 so the sanding disc faces upwards.
2. Guide the open-end wrench under the sanding disc and move it horizontally until it engages, holding the thread in place.
3. Loosen the sanding disc by turning it, then remove it.
4. Fasten the new sanding disc by turning it by hand until it is hand-tight.
What are the different operating modes available on the PARKSIDE PPEXS 750 B2?
You can switch between two modes using the changeover switch. Only change the mode when the sanding disc is stationary:
Rough grinding (direct drive): Provides constant eccentric and rotational movement, suitable for high abrasion when processing coarse, resistant surfaces and for grinding polishing.
Fine grinding (free wheel): Provides constant eccentric motion with rotational motion dependent on contact pressure, suitable for sensitive surfaces and fine polishing.
How do I operate the PARKSIDE PPEXS 750 B2?
1. Press the Unlock button; the speed level display will light up.
2. Select the desired speed level (1 to 6) using the speed button.
3. Press the On/Off button.
4. Wait until the device reaches full speed before guiding the sanding disc against the workpiece.
5. To turn off, remove the disc from the workpiece, then press the On/Off button.
What should I do if the PARKSIDE PPEXS 750 B2 is not starting?
| Problem | Possible Cause | Error Correction |
|---|---|---|
| Device does not start | No mains power supply | Check the socket, mains connection cable, plug, and fuse. |
| Device does not start | On/Off button defective | Contact the service centre. |
| Device does not start | Defective motor | Contact the service centre. |
What should I do if the PARKSIDE PPEXS 750 B2 works with interruptions?
| Problem | Possible Cause | Error Correction |
|---|---|---|
| Works with interruptions | Internal loose contact | Contact the service centre. |
| Works with interruptions | On/Off button defective | Contact the service centre. |
| Works with interruptions | Worn out carbon brushes | Replace the carbon brushes. |
How do I replace the carbon brushes in the PARKSIDE PPEXS 750 B2?
Always replace both carbon brushes at the same time using a PH2 Phillips screwdriver.
1. Pull out the mains plug.
2. Remove the screw on the service panel and remove the panel.
3. Remove the contact screw and remove the carbon brush assembly.
4. Remove the blade receptacle from the assembly and put it on the new carbon brush assembly.
5. Insert the new assembly into the device, pressing against it from below.
6. Fasten the assembly and ring cable lug using the contact screw, ensuring the wire runs correctly as shown in the illustration.
7. Reattach the service panel with the screw.
CLICK HERE TO DOWNLOAD PARKSIDE PPEXS 750 B2 (01) PDF DOCUMENT