SHARK FLEXSTYLE HD400 (03) PDF Document

To operate the Cool Shot Button on the SHARK FLEXSTYLE HD400, press and hold the Cool Shot button as desired to seal the hair cuticle and lock in your styles. All 3 red temperature lights will be OFF when the Cool Shot is engaged.

To attach a styler attachment to the SHARK FLEXSTYLE HD400, push the styler onto the nozzle until it clicks.

To remove a styler attachment from the SHARK FLEXSTYLE HD400, slide the Styler Lock down to unlock the styler so it can be removed. You can also hold the accessory by the tip when removing it, or hold the Cool Touch location to remove each accessory after use.

To switch the SHARK FLEXSTYLE HD400 from Styler to Hair Dryer mode, slide the Hinge Latch down and rotate the nozzle left to switch to the hair dryer mode.

The Airflow settings for the SHARK FLEXSTYLE HD400 are Low, Medium, or High.

The Temperature settings for the SHARK FLEXSTYLE HD400 are No Heat, Low, Medium, or High.

The recommended setting for the 1.25″ Auto-Wrap Curlers on the SHARK FLEXSTYLE HD400 is high air flow and high heat. You should also use the Cool Shot button to seal the hair cuticle and lock in your styles.

The steps to use the 1.25″ Auto-Wrap Curlers on the SHARK FLEXSTYLE HD400 are as follows:

Step 1: Begin with slightly damp hair, 80-90% dry. Detangle and section top and bottom. Choose your barrel according to the side you want to curl. Pro Tip: Hair that is too wet will be more difficult to curl.

Step 2: Hold the middle of a small section of hair and allow at least 3 inches of your ends to line up with the arrow on the barrel. Make sure the wand is upright and your hair is in front of the curler. Pro Tip: Smaller sections of hair allow for easier wrapping.

Step 3: Turn on high heat and high air flow. The airflow will automatically pick up the ends of your hair. Move the wand towards your head as your hair wraps around the curler. Continue to use your hand to guide your hair through the barrel until it feels secure. Hold for 10 seconds. Pro Tip: Hair will secure after 2-3 wraps around the barrel.

Step 4: With hair securely wrapped around the barrel as shown in step 3, press and hold the Cool Shot button for 10 seconds to lock in your curl. Pro Tip: Using Cool Shot allows for longer-lasting curls.

Step 5: Turn the unit off and pull the barrel straight down to reveal your perfect curl! Pro Tip: Use a setting or holding spray as desired for an even longer lasting look.

The recommended setting for the Oval Brush on the SHARK FLEXSTYLE HD400 is medium airflow and medium heat.

The steps to use the Oval Brush on the SHARK FLEXSTYLE HD400 are as follows:

Step 1: Begin with rough-dried or towel-dried hair. Pro Tip: Apply hair products or styling agents as desired.

Step 2: Section your hair as desired. For voluminous blowouts, start by placing the round brush under the hair close to the roots. Pro Tip: For even more volume, hold the brush under hair close to the roots for 3 seconds before brushing outward.

Step 3: Roll the brush outward from the roots to the ends to engage the bristles and gently grip the hair. Pro Tip: For extra volume, brush your hair in an upward direction.

Step 4: Repeat on remaining sections until hair has been dried into a bouncy, voluminous style. Pro Tip: Set your style and help reduce frizz by pressing the Cool Shot button.

The additional styling tips for using the Oval Brush on the SHARK FLEXSTYLE HD400 are:

If you have fine hair, try reducing the airflow to help cut down on frizz.

If you have thick hair, try increasing the heat for even faster results.

If you have curly or coily hair, try increasing the heat to help achieve a straighter style.

For an added curl, place the brush under the ends of the hair and roll the brush toward the roots to engage the bristles. Twist the hair off the brush to release the curl.

The recommended setting for the Round Brush on the SHARK FLEXSTYLE HD400 is medium airflow and medium heat. The Pro Tip states it works great on bangs and short hair.

The steps to use the Round Brush on the SHARK FLEXSTYLE HD400 are as follows:

Step 1: Begin with rough-dried or towel-dried hair. Pro Tip: Apply hair products or styling agents as desired.

Step 2: Section your hair as desired. For voluminous blowouts, start by placing the round brush under the hair close to the roots. Pro Tip: For even more volume, hold the brush under hair close to the roots for 3 seconds before brushing outward.

Step 3: Roll the brush outward from the roots to the ends to engage the bristles and gently grip the hair. Pro Tip: For extra volume, brush your hair in an upward direction.

Step 4: Repeat on remaining sections until hair has been dried into a bouncy, voluminous style. Pro Tip: Set your style and help reduce frizz by pressing the Cool Shot button.

The additional styling tips for using the Round Brush on the SHARK FLEXSTYLE HD400 are:

If you have short hair, try reducing the airflow to help cut down on frizz and flyaways.

If you have thick hair, try increasing the heat for even faster results.

If you have curly or coily hair, try increasing the heat to help achieve a straighter style.

For an added curl, place the brush under the ends of the hair and roll the brush toward the roots to engage the bristles. Twist the hair off the brush to release the curl.

The recommended setting for the Paddle Brush on the SHARK FLEXSTYLE HD400 is high airflow and medium heat.

The steps to use the Paddle Brush on the SHARK FLEXSTYLE HD400 for sleek, straight styles are as follows:

Step 1: Begin with rough-dried or towel-dried hair. Section your hair as desired. Pro Tip: Apply hair products or styling agents as desired.

Step 2: For a smooth, sleek style, start by placing the brush close to the roots to engage the detangling bristles.

Step 3: Brush down your hair, making sure to engage the smoothing bristles, and gently grip the hair. Pro Tip: Hold the ends of your hair while brushing for added tension and smoothing.

Step 4: Repeat on remaining sections until hair has been dried into a smooth, straight style. Pro Tip: Set your style and help reduce frizz by pressing the Cool Shot button.

The additional styling tips for using the Paddle Brush on the SHARK FLEXSTYLE HD400 are:

If you have fine hair, try reducing the airflow to help cut down on frizz.

If you have thick hair, try brushing smaller sections for smoother results.

If you have curly or coily hair, try repeatedly brushing smaller sections and increasing the heat to help achieve a straighter style.

For added volume, place the brush under the hair section close to the roots and brush upward using a rounding motion.

The recommended setting for the FrizzFighter™ Finishing Tool on the SHARK FLEXSTYLE HD400 is high airflow and medium heat.

The steps to use the FrizzFighter™ Finishing Tool on the SHARK FLEXSTYLE HD400 are as follows:

Step 1: Begin with completely dry hair that has been styled with a concentrator or style brush. Pro Tip: Works best on straight or straightened hair.

Step 2: Start at the top of your head, close to the roots. Hold until the hair attracts.

Step 3: Slowly glide the FrizzFighter™ Finishing Tool down the length of your hair. Gently touch your hair with the tool-no need to press it against your head.

Step 4: Repeat around your head.

The additional styling tips for using the FrizzFighter™ Finishing Tool on the SHARK FLEXSTYLE HD400 are:

If you have thinner/finer hair you can decrease the airflow to help reduce flyaways.

If you have thinner/finer hair you can decrease the heat.

The recommended setting for the Styling Concentrator on the SHARK FLEXSTYLE HD400 is high airflow and medium heat.

The steps to use the Styling Concentrator on the SHARK FLEXSTYLE HD400 for smooth, stylish blowouts are as follows:

Step 1: Begin with rough-dried or towel-dried hair. Pro Tip: Apply hair products or styling agents as desired.

Step 2: Section your hair as desired and start styling with a round brush. Rotate the concentrator so airflow is always in line with the round brush.

Step 3: Apply heat in a downward motion for smoothing. Pro Tip: Apply heat at ends for shaping and bending.

Step 4: Finish styling by setting shape at ends and pressing the Cool Shot button.

The additional styling tips for using the Styling Concentrator on the SHARK FLEXSTYLE HD400 are:

If you have thinner/finer hair, try reducing the airflow to help cut down on frizz.

To create a curl, wrap your hair around a round brush and dry it in place using the concentrator.

For added volume, place a round brush under the roots and brush upward while drying with the concentrator.

For an added curl at the ends, roll the ends of your hair onto a round brush and dry in place using the concentrator.

The recommended setting for the Curl-Defining Diffuser on the SHARK FLEXSTYLE HD400 is medium airflow and low temperature, using the Cool Shot button as desired.

The steps to use the Curl-Defining Diffuser on the SHARK FLEXSTYLE HD400 to define natural curls are as follows:

Step 1: Begin with towel-dried hair. Working around your head, bunch curls from ends between the petals of the diffuser. Pro Tip: Apply curly hair products or styling agents as desired to wet hair.

Step 2: Bring the diffuser up to the roots. Pause and hold.

Step 3: For more volume, slide the lever to extend prongs to lift roots higher. Pro Tip: Gather hair in diffuser with prongs retracted, then extend them when you reach the roots to increase grab and maximize airflow.

Step 4: If desired, flip upside down and bunch from below for extra volume. Pro Tip: Keep the integrity of your natural curls by switching between Low temp and the Cool Shot button.

The additional styling tips for using the Curl-Defining Diffuser on the SHARK FLEXSTYLE HD400 are:

Apply curly hair products to wet hair before drying to help define your curls and cut down on frizz.

If you have thick hair, try increasing the heat for even faster results.

The recommended setting for the Wide-Tooth Comb on the SHARK FLEXSTYLE HD400 is high airflow and medium heat.

The steps to use the Wide-Tooth Comb on the SHARK FLEXSTYLE HD400 to stretch natural hair are as follows:

Step 1: Begin with towel-dried hair. Section your hair as desired. Make sure to detangle each section to help prevent snagging. Pro Tip: Apply your favorite styling products as desired.

Step 2: Slowly comb your hair from the roots to the ends. Continue combing the section until hair has been stretched and dried. Pro Tip: Hold the ends of your hair while combing for added tension and length.

Step 3: Repeat on remaining sections. Press the Cool Shot button to lock in your style. Pro Tip: Detach and re-orient the comb as needed to easily reach all areas on your head.

Step 4: Continue styling your stretched hair as desired.

The additional styling tips for using the Wide-Tooth Comb on the SHARK FLEXSTYLE HD400 are:

Try using the comb while in styling wand mode for more styling versatility.

For added volume at the roots, comb through hair in an upward direction.

Decrease the heat to help maintain hair texture while stretching.