FREE ENGLISH ROBOT-COUPE MINI MP 220 COMBI (01) PDF USER GUIDE
FREE ENGLISH ROBOT-COUPE MINI MP 220 COMBI (01) PDF USER MANUAL
FREE ENGLISH ROBOT-COUPE MINI MP 220 COMBI (01) PDF OWNER GUIDE
FREE ENGLISH ROBOT-COUPE MINI MP 220 COMBI (01) PDF OWNER MANUAL
FREE ENGLISH ROBOT-COUPE MINI MP 220 COMBI (01) PDF REFERENCE GUIDE
FREE ENGLISH ROBOT-COUPE MINI MP 220 COMBI (01) PDF INSTRUCTION GUIDE
FREE ENGLISH ROBOT-COUPE MINI MP 220 COMBI (01) PDF REFERENCE MANUAL
FREE ENGLISH ROBOT-COUPE MINI MP 220 COMBI (01) PDF INSTRUCTION MANUAL
FREE ENGLISH ROBOT-COUPE MINI MP 220 COMBI (01) PDF OPERATING INSTRUCTIONS
CLICK HERE TO DOWNLOAD ROBOT-COUPE MINI MP 220 COMBI (01) PDF MANUAL
If this is not the document you want for this product, click here to see if we have any other documents for this product.
ROBOT-COUPE MINI MP 220 COMBI (01) PDF SUMMARY:
How should the equipment be unpacked?
Carefully remove the equipment from the packaging and take out all the boxes or packets containing attachments or specific items.
What precaution should be taken when handling the blade?
Wear cut-resistant gloves when handling the blade, as some parts are very sharp.
Where is it advised to store the power mixer?
It is advised to install the wall support provided with the machine and to store your machine on it.
What should always be checked regarding the power supply?
Always check that your power supply corresponds to that indicated on the serial number plate on the motor unit and that it is properly sized.
What is the standard power outlet required for operation?
The standard machine is operated on a standard 120 Volt, 60Hz., 15 Amp outlet.
What is recommended for optimum mashed potatoes quality?
For an optimum result in the mashed potatoes quality, it is recommended to process at low speed.
What safety features are included on the motor?
Safeties on motor include thermal and overload protection.
What happens if there is an obstruction or the machine is overused and becomes hot?
If there is an obstruction in the container or the machine is overused and becomes hot, the power mixer will stop.
What should you do if the power mixer stops due to thermal overload?
If the power mixer stops because of a thermal overload (power mixer is too hot), wait for a period of up to 30 minutes for the power mixer to cool down before restarting.
What is the no volt release safety?
If there is a power failure or the machine is unplugged, it will not restart by itself.
What should you be careful about when handling the blades?
Be careful when handling the blades. They are very sharp! Wear cut-resistant gloves when handling the blades.
What should be followed very carefully to prevent accidents?
In order to prevent accidents such as electrical shock, personal injury, fire, and in order to limit property/product damage when using your power mixer, follow the instructions very carefully and strictly adhere to them.
Who should read the manual?
This manual should be kept nearby for reference and should be read by all first time users of the power mixer.
What are the blade attachment capacities for the Mini MP 170 V.V. and Mini MP 220 V.V.?
The Mini MP 170 V.V. can process up to 4 3/8 quarts and the Mini MP 220 V.V. up to 7 quarts.
What are the whisk attachment capacities for the Mini MP 170 Combi and Mini MP 220 Combi?
Using the whisk attachment, Mini MP 170 Combi and Mini MP 220 Combi can process up to 20 egg whites and puree from 2 to 16 pounds.
What is advised for electrical connections?
The appliance should be plugged into a grounded outlet.
What should you make sure of regarding the voltage of the power supply?
Make sure that the voltage of your power supply matches that shown on the identification plate of your appliance.
What should you do if the power mixer stops unexpectedly due to overload protection?
If the power mixer stops unexpectedly, you may try to restart it by following steps 3-5 below. If the power mixer does not restart, allow it to cool for a period of up to 30 minutes and the temperature overload will automatically reset.
How do you operate the power mixer?
- Plug the power mixer into the power outlet, making sure you do not press the button (CB).
- Insert the foot into the preparation.
- Press the control button (CB), and the power mixer will start up.
- To stop the power mixer, release the control button (CB).
How do you operate the variable-speed function?
Follow steps 1 to 4 above, then change the speed of the motor by turning the variable speed button (MV) towards the maximum or minimum as required.
What are the speed ranges for the whisk and mixer functions?
- Whisk function (Mini MP 170 Combi, Mini MP 220 Combi): speed between 350 and 1 560 rpm.
- Mixer function (Mini MP 170 V.V., Mini MP 220 V.V., Mini MP 170 Combi, Mini MP 220 Combi): speed between 2 000 and 12 500 rpm.
What is advisable when using the whisk?
It is advisable to start at a low speed when using the whisk.
What does the self-regulating speed system do?
With the self-regulating speed system, once you have selected a speed, it will remain constant, even if the consistency of your mixture changes.
What is the length of the shafts for the Mini MP 170 V.V. / Combi and Mini MP 220 V.V. / Combi models?
The shafts measure 6 5/8 inches and 8 5/8 inches long respectively.
What are the power mixers suitable for?
They will enable you to make soups, vegetables purées and cereal preparations with little effort.
What is the whisk attachment ideal for?
The whisk attachment is ideal for making pancake batter, mayonnaise, beaten egg whites, chocolate mousse, butter sauces, whipped cream or smooth fromage frais.
What does the variable-speed function enable you to do?
The variable-speed function will enable you to adjust the speed to suit each preparation and to start the processing at a lower speed in order to reduce splashing.
How do you attach the shaft to the motor unit?
- Unplug the power mixer.
- Note that each end of the shaft has a threaded plastic piece. One is longer than the other and doesn’t have a rubber “O” ring. Insert this longer plastic end into the motor housing.
- Turn the shaft in the direction of the arrow until it is tight.
How do you remove the shaft from the motor unit?
- Unplug the power mixer.
- Turn the shaft counterclockwise until it is removed.
How do you attach the bell to the tube?
- Unplug the power mixer.
- Insert the threaded shaft into the housing of the bell.
- Turn the bell in the direction of the arrow (see drawing) until it is tight.
How do you remove the bell from the tube?
- Unplug the power mixer.
- Turn the bell in the direction of the arrow to detach it from the tube.
What is recommended for a more ergonomic approach?
Hold the handle of the appliance in one hand and the container with the other.
What should you make sure of when using the power mixer?
- Tilt the power mixer slightly, making sure that the bell does not touch the bottom of the container.
- Always make sure that the bell is sufficiently immersed to avoid splashing and that the air vents of the motor unit do not come into contact with any liquid.
- For optimum efficiency, two thirds of the shaft should be immersed in the preparation.
- Do not rest the bell against the bowl.
- The splashguard should always be in place.
How do you hold the power mixer when using the whisk function?
Hold the power mixer by the handle and the bottom of the motor unit. You can also hold the appliance by the handle with one hand, leaving the other hand free to hold the bowl, if necessary.
What is recommended when processing with the whisk?
Move the whisk around in the bowl, in order to obtain a perfectly homogenous mixture. Keep the whisk from touching the sides of the bowl. For maximum efficiency, at least one-fifth of the whisk length should be immersed. Start the processing at a low speed.
How do you remove the casing?
- Check that the machine is not plugged in.
- Turn the gear box in the opposite direction to that used when attaching it.
How do you fit the whisks into the gear box?
- Grasp the holder in one hand.
- With the other hand, take the first whisk and insert the shaft into the bore of the gear box drive shaft. Make sure the drive lugs are properly aligned with the notches.
- As you push the whisk into the gear box drive shaft, rotate it slightly in order to slot the drive lugs into the notches of the drive shaft, thereby locking the whisk into place inside the shaft.
- Repeat this procedure with the second whisk. If you cannot push it in properly, remove it, rotate it 90° and start again.
How do you remove the whisks from the gear box?
Pull the whisk in direction to the arrow, gripping the ejector in one hand and the holder in the other.
How do you attach the gear box to the motor unit?
- Check that the machine is not plugged in.
- Insert the threaded part into the motor unit.
- Turn the gear box in the direction of the arrow (see figure) until it is locked into place moderately tightly.
How do you install the emulsifying disc?
- Introduce the disc into the bell.
- Hold it in place using the locking tool.
- Turn the drive coupling with this tool until it starts to tighten.
How do you remove the emulsifying disc?
The disc can be removed in the same way as the blades.
How do you remove the blade?
- Unplug the power mixer.
- Hold the blades with the provided blade-locking tool.
- Using the blade-locking tool, unscrew the drive coupling then remove the blade for easy cleaning.
How do you assemble the splash guard?
Cover the ring with the splash guard protection sliding it all along the foot in the arrow direction, the flange must be oriented down.
How do you remove the splash guard protection?
To remove the splash guard protection for cleaning follow the instruction in the reverse order.
How should you clean the power mixer?
Clean immediately after use to prevent product from sticking to surfaces. The power mixer must be clean through all stages of production. Clean between each job using a detergent or disinfectant.
What should you use to clean the power mixer?
Use a cloth lightly dampened (not dripping) with the cleaning solution.
What should you be careful about when cleaning the motor housing?
Do not allow liquid to come into contact with the electrical components contained within the housing. Be careful when cleaning around vents do not allow liquid to drip or seep into the housing.
How should you clean the motor housing?
Use a cloth lightly dampened (not dripping) with water to remove detergent/disinfectant then dry using a clean cloth.
What should you do before disassembling the bell from the shaft after using the power mixer in a hot mixture?
Cool the bottom of the tube in cold water.
What should you do with the parts after cleaning?
Thoroughly dry all parts before reassembling.
How do you clean the shaft and bell?
There are two ways to proceed: * Simple cleaning procedure: Submerge the shaft and bell in water and run for a few seconds to clean. Unplug the power cord. * Complete cleaning procedure: Unplug the power mixer and rinse the bell under a water tap. Remove the bell from the shaft, then remove the blade (wear cutting gloves).
How do you clean the blade and emulsifying disc?
The blade and the emulsifying disc can be removed from the bell for thorough cleaning. Always dry thoroughly to avoid spotting.
How do you clean the whisks?
The whisks can be cleaned either by hand or in a dishwasher.
What should you never do with the gear box?
Never immerse the gear box in water or in a dishwasher. Clean it with a slightly damp cloth or sponge.
What type of cleaning agents should you use on aluminum parts?
Use soft-metal-safe cleaning agents.
What should you be careful about when using cleaning agents on plastic parts?
Be careful, many cleaning agents are corrosive and are not safe for use on plastics! Do not use strong alkaline detergent (having a high concentration of soda or ammonia).
What should you do when the blades become worn?
Over time the blades will become worn and will need to be replaced. The washer and seals should also be replaced at this time. A blade service kit is available.
What should you do to maintain a watertight seal between the shaft and bell?
Inspect the seal for wear and replace it if necessary.
What should you do if the power mixer does not start?
- Did you follow the previous operating instructions?
- Pull the plug and try another outlet.
- Check outlet for current (breaker or fuse).
- Call local Robot Coupe authorized service agency.
What should you do if the power mixer stops during processing?
See the section on Operating the power Mixer. The first paragraph describes the overload protection. It may be necessary to allow the machine to cool for up to 30 minutes before restarting.
What should you do if you cannot locate the cause of the problem?
- Release the control button (CB).
- Unplug the power mixer.
What is recommended when handling the blades?
It is recommended that cutting gloves be worn when handling the blades. Handle and store the blades with safety in mind.
What should you never do with the safety mechanisms?
Never try to override or defeat the purpose of the safety mechanisms.
What should you never put near the blades on the power mixer?
Never put anything (utensils etc.) but food material near the blades on the power mixer.
What should you never do with the power mixer?
- Never overload the power mixer.
- Never turn the power mixer on, unless the bell is completely immersed in the product.
What should you always do before cleaning or maintenance?
Always unplug the power mixer before doing any cleaning or maintenance.
What should you check if the drive shaft is not rotating?
Unplug the power mixer, remove the bell and test the rotation of the end of the drive shaft manually.
What else should be checked if the power mixer is not working?
Check the condition of the plug and the power cord.
What should you do if the power mixer starts to smell hot or smoke?
Turn the power mixer off and unplug it. Call your local authorized service agency.
What should you do if your unit requires service?
Check with your distributor to see where local service is available. If not or if you wish your unit to be serviced at the factory, call for return instructions and ship the unit prepaid to the factory address.
What is the importance of the metal wires on the whisk?
The success of your preparation will depend essentially on the state of the metal wires and their amount of wear and tear. They should therefore be replaced from time to time in order to ensure optimum quality of the finished product.
What should you do when you use the tube with the bell for making a preparation and then you want to use the whisk?
You need to remove the splashguard assembly from the tube and install it on the gearbox. The process to install the splashguard is the same for the whisk and the tube.
What should you never immerse in liquid?
Never immerse motor housing and/or handle in liquid! The housing contains the electrical components and is not sealed against liquid. Contact with liquid can cause damage to the blender and serious injury to the operator.
What should you always do before cleaning the power mixer?
Always unplug the power mixer before cleaning it! Always dilute bleach according to the instructions on the label.
What should you never do with the power mixer?
Never run the power mixer through a dishwasher! The type and concentration of the sanitation agent must comply with 21 CFR 178.1010 regulations.
CLICK HERE TO DOWNLOAD ROBOT-COUPE MINI MP 220 COMBI (01) PDF MANUAL