RENPHO R-Q002 (01) PDF Document

Before using the RENPHO R-Q002, please be aware of the following warnings:

1. Children under the age of 14, persons with reduced physical, sensory or mental capabilities, as well as persons with a lack of knowledge must be given supervision or instruction before using the bike. DO NOT allow children to perform maintenance without supervision or to play with the bike.

2. The provided adapter has passed CQC certification and can be used with this bike only. Do not use it with any other products.

3. The bike should not be used by persons exceeding 120kg/265lb in weight.

4. The bike is not for medical use of any kind.

5. Consult a physician before beginning a new fitness plan. Incorrect or excessive training can result in serious injury.

6. If you experience dizziness, nausea, chest pain, shortness of breath or any other abnormal symptoms, stop exercising immediately and consult a physician.

7. Only one person should use the equipment at a time.

8. Keep hands away from all moving parts.

9. Always wear appropriate workout clothing when exercising. DO NOT wear loose or baggy clothing as it may get caught in the equipment. Always wear athletic shoes to protect your feet while exercising.

10. DO NOT place any sharp objects around the equipment.

Please follow these important safety instructions when operating the RENPHO R-Q002:

1. The bike is for home use only.

2. Please correctly connect the power adapter before use.

3. To avoid injury, warm up before using the bike.

4. Incorrect or excessive training can result in serious injury.

5. To avoid accidents, keep the bike out of the reach of children and pets.

6. To avoid getting hurt, keep your hands away from any moving parts of the bike.

7. Use only original parts from the manufacturer. Changes or modifications to this unit voids the warranty.

8. In case of malfunction, stop using the bike immediately.

9. Make sure to secure your feet with the pedal straps while using the bike.

10. The bike should be placed on a solid, level and horizontal surface. Allow a clearance of 60cm on each side of the bike.

11. Perform regular maintenance for optimal performance and longevity. To ensure safety, the bike must be checked for wear and damage on a regular basis.

12. Replace any damaged or worn parts immediately. Do not use the bike until the repair is performed.

13. In case of inaccurate display of resistance or power, please restart the bike while not used.

14. Do not operate this device if it has a damaged cord or plug, if it is not working properly, or it is wet.

DANGER: Always unplug the power cord when the bike is not in use or before cleaning.

The main components of the RENPHO R-Q002 are:

1. Console

2. Pad holder

3. Handlebar

4. USB port

5. Console post

6. Handlebar height L-handle

7. Pedal

8. Crank

9. Front stabilizer

10. Transport wheels

11. Leveling feet

12. Rear stabilizer

13. Power port

14. Power button

15. Seat height L-handle

16. Seat post

17. Seat front-to-back adjustment knob

18. Seat

The RENPHO R-Q002 comes with the following accessories:

• 5mm Allen wrench x 1

• 6mm Allen wrench x 1

• 15mm Open-end wrench x 1

• Power adapter x 1

• M6 screws x 4

• M10 screws x 4

• Bike stabilizer x 2

• Pedals x 2

• Pad holder x 1 (Pre-installed)

• User Manual x 1

• Quality certificate x 1

Product Name: AI-Powered Exercise Bike

Model No.: R-Q002

Display: LED nixie tube

Wireless Connection: Bluetooth

Equipment Type: Pedal exerciser

Braking: Non speed-dependent

Resistance: Smart motor damping

Drive: Belt drive

Power Adapter: Input: AC 100-240V, 0.6A 50/60Hz; Output: DC 12V 1.5A

Rated Power: 18W

Max Weight Allowed: 120kg / 265lb

Max Height Allowed: 150-190cm / 59-75in

Net Weight: 35kg / 77lb

Gross Weight: 40kg / 88lb

Follow these steps to set up your RENPHO R-Q002:

1. Install bike stabilizers: Place the front and rear stabilizer as indicated, install four M10 screws and tighten them with a 6mm Allen wrench.

2. Connect the tube: Connect the tube inside the handlebar to the one inside the console post. Pay attention to the direction when inserting.

3. Mount the handlebar: With the tube well connected, mount the handlebar to the console post. Lock 4 M6 screws with a 5mm Allen wrench. Make sure to place the screw shim properly, with the cambered surface clung to the post.

1. Install the pedal straps: Mount the pedal strap with the ‘L’ sign to the left pedal and the one with the ‘R’ sign to the right pedal.

2. Mount the left pedal: Mount the pedal with the ‘L’ sign to the left side crank, fastening it with a 15mm open-end wrench in an anti-clockwise direction.

3. Mount the right pedal: Mount the pedal with the ‘R’ sign to the right side crank, fastening it with a 15mm open-end wrench in a clockwise direction.

1. Turn the handlebar height L-handle counterclockwise to loosen the console post.

2. Adjust the handlebar to a proper height.

3. Turn the L-handle clockwise to tighten.

4. Pull the L-handle outwards.

5. Turn the L-handle to a vertically downward direction.

1. Turn the seat height L-handle counterclockwise to loosen the seat post.

2. Adjust the seat height until you feel comfortable. For your safety, make sure to keep the STOP mark inside the frame while adjusting.

3. Turn the L-handle clockwise to fix the seat post.

4. Pull the L-handle outwards.

5. Rotate the L-handle to a vertically downward direction. It is important to keep the L-handle vertically downwards as projecting handles will interfere with your movements.

To set the correct seat height on your RENPHO R-Q002, sit on the saddle and place your heel on the pedal. Make sure the crank arm supporting your foot is pointed down and in line with the seat post. You are at the correct seat height if your leg is now fully extended (straight, but without overextending your knee).

To adjust the seat depth, turn the adjustment knob clockwise to loosen. Move the seat forward or back to your desired position. Then, turn the knob counterclockwise to tighten and secure the seat.

The RENPHO R-Q002 has four leveling feet on the front and rear stabilizers. To stabilize the bike, rotate each leveling foot until the bike rests firmly on the floor without wobbling.

Connect the power adapter to the power port on the bike and connect the power plug to a suitable socket. Then, turn the power button to the “-” position to power on the RENPHO R-Q002.

The console on the RENPHO R-Q002 works by either rotating its metal frame or pressing the knob. Rotating the metal frame adjusts resistance. Pressing the knob can be used to pause, resume, or end a workout when using a connected app. A slight touch at the bottom middle area of the console panel will change the data display.

The units displayed on the console are:

• N.m: newton meter, unit of torque

• W: watt, unit of power

• r/min: revolutions per minute, unit of frequency

Bluetooth ON: Turn on the AI Gym App and search for your bike to connect. When connected, the Bluetooth indicator on the console stays on.

Bluetooth OFF: Touch the bottom middle area of the console to enter the Bluetooth interface. Press and hold the knob to turn it off. When disconnected, you will need to manually reconnect your bike in the App.

Switch Data Display: Each slight touch at the bottom middle area of the console panel will change the data display between Duration, Resistance (Gear), Power, and Cadence.

Control a Workout: When you are taking a riding course or an immersive road riding on the App, press the knob to pause (when paused, the indicating lines flash). Press the knob again to resume your ride. Press and hold the knob to end the ride (when ended, the indicating lines remain displayed).

1. Search and download “AI Gym” in the Apple App Store or Google Play.

2. Sign up or Log in. Use your email address to register and create a new account, then log in. If you already have a Renpho account, you can log in directly.

3. Click “Add device” to search for your RENPHO R-Q002. Wait for the search to complete.

4. After the search is complete, select the correct device (R-Q002) for binding. Once the device is bound, you can view detailed information about it, edit its name, or unbind it.

1. Log in with your Zwift user account and select POWER SOURCE on the main interface.

2. After clicking “POWER SOURCE”, the device list interface will pop up. Select your device name (R-Q002) from the list and click “OK”.

3. After the pairing is successful, click “Let’s Go” to start your ride.

1. This bike is for indoor home use only. Do not store the bike outdoors, near water, or at high humidity levels.

2. Please store in a place with shade and shelter to avoid any damage to the surface.

3. Inspect regularly all screws or parts that need fastening.

4. Inspect the bike seat regularly. Tighten the nuts whenever they get loose. Inspect the cranks and pedals regularly. Tighten them if necessary.

5. Clean the bike regularly.

If your RENPHO R-Q002 is making noise while pedaling, try the following solutions:

1. Remove the pedals from the cranks and turn the pedal axis. If it turns smoothly, mount the pedals back on. If the turning is unsmooth, consult service personnel for a replacement.

2. Rotate the cranks. If noise is present, tighten the crank screws.

To fix wobbly handlebars on your RENPHO R-Q002, use a 5mm socket head wrench to tighten the four screws on the handlebars.

If the seat on your RENPHO R-Q002 is unstable, first adjust the seat to your proper height. Then, use a monkey wrench to fasten the nuts on both sides under the seat saddle.

To fix an unstable bike frame on your RENPHO R-Q002, tighten the four screws on the four leveling feet using a 6mm socket head wrench.

If there is no display on the console of your RENPHO R-Q002, please check the following:

1. Re-connect the power adapter.

2. Make sure the power adapter is properly connected to the bike.

3. Make sure the power button is turned to the “-” position.

If you are experiencing a Bluetooth connection failure with your RENPHO R-Q002, restart your bike and your phone or pad, then try to re-connect.

If your RENPHO R-Q002 is failing to connect with the app, try keeping your phone close to the bike and then attempt to re-connect.