REDMOND RHC-6201 (01) PDF Document

Before initial start-up, check that the product specifications match the mains supply.

The device is not intended for use by persons (including children) with reduced physical, sensory or mental abilities, or lack of experience or knowledge, unless they are supervised or instructed.

To recharge the battery, use only the standard removable adapter that is supplied with the device.

The hair clipper should only be powered by the safety extra-low voltage marked on the device.

Do not leave the appliance switched on and unattended.

This appliance is intended for household use only and is not suitable for industrial use.

Use the appliance only for its intended purpose. Do not use attachments and cords from other devices.

Do not use the appliance if the cord or plug is damaged, or if the appliance is damaged or defective.

Do not pull on the cord, twist it, or wind the cord around the appliance. Do not let the cord hang over the edge of a table or over hot surfaces.

Do not place or store the device in places where it may fall into a sink or tub. Do not use the appliance while taking a bath or shower.

Do not touch the appliance if it falls into the water. Disconnect the power immediately.

Regularly lubricate the blades.

Do not use the hair clipper if the skin is inflamed or for clipping animals.

Hair clipper (1 pc.)

Adapter (1 pc.)

Detachable heads: 3, 6, 9, 12mm (4 pcs.)

Oil cup (1 pc.)

Brush for blades (1 pc.)

Stand (1 pc.)

Bag for storage (1 pc.)

Comb for beard (1 pc.)

Instruction manual (1 pc.)

Carefully remove the product and its accessories from the box and remove all packing materials and advertising stickers.

Wipe the product body with a damp cloth and let it dry.

Be sure to save the warning labels and the serial number sticker on the body of the device.

After transportation or storage at low temperatures, keep the device at room temperature for at least 2 hours before turning it on.

Hair clippers are supplied with a partially charged battery but must be charged before operation.

To charge, turn off the device using the on / off button, insert the power cord into the socket of the hair clipper, and connect it to the mains.

The indicator light will turn on and glow red during charging.

A full charge of the battery lasts no more than 45 minutes of continuous operation. The battery should be charged further if the blades of the cutting unit stop or move slowly.

The maximum battery capacity is reached only after several complete charge-discharge cycles.

Charging a partially discharged battery reduces its capacity and life. Charging time is about 8 hours.

You can use the hair clipper while it is charging.

Recharge the battery at least once every 6 months, even if the device is not in use.

Inspect the hair clipper and ensure the blades are lubricated before cutting hair.

Turn on the device to distribute the oil and ensure the blades slide smoothly. Wipe off any excess oil.

Place a towel around the neck and shoulders of the person you are cutting.

Comb the hair thoroughly before cutting.

It is recommended to start the haircut by choosing the maximum hair length, gradually reducing the length setting.

To fix the selected hair length settings, move the hair growth device in different directions (up, down, or across).

For the most effective haircut, move against the hair growth.

To avoid overheating the motor, do not use the machine continuously for more than 25 minutes.

If necessary, take one of the removable heads and insert the guides into the corresponding slots.

Gently push the head in until it clicks into place.

You can also use the device without a head for a closer cut.

The clipper should be cleaned and lubricated after each use.

Never wash parts of the appliance in the dishwasher. Do not use chemicals or abrasives. Always unplug the appliance before cleaning.

Clean the body with a soft cloth. Do not wash the hair clipper under a stream of water and do not immerse it in water or other liquids.

Use a brush to clean the unit and the attachments.

Apply 1-2 drops of lubricating oil to the unit’s blades after cleaning.

Ensure that the appliance and all its accessories are clean and dry before storing it.

The device must be stored indoors, in conditions that preserve the presentation of the product.

Do not expose the device to shock loads during handling operations.