RCA LRK50G45RQ (01) PDF DOCUMENT

The following accessories are included with your RCA LRK50G45RQ TV:

• LED TV (stand separated from cabinet)

• Remote Control & Batteries

• User’s manual + Quick Start Guide + Stand Installation Guide + Patent Card

• TV Stand Neck

• TV Stand

• TV Stand Screws (M4 x 15mm, 6pcs, Part# RS01TM415H and M4 x 14mm, 4pcs, Part# RS01PWA414HT)

• Roku® Streaming Stick™ (Roku Ready® Version)

Please follow these steps to connect and power on your TV:

Step 1. Use an antenna cable to connect the ATSC/NTSC signal to the LED TV’s TV CABLE terminal. Connect the TV to the power AC 100-120V 60Hz. It is recommended to connect power after all other connections have been made.

Step 2. Connect the TV to the power outlet. Press the power button on the side of your TV or the POWER button on your remote control to turn on the TV.

The following table details the available input sources and their corresponding jacks on the RCA LRK50G45RQ TV.

The TV is packaged with the TV stand separated from the cabinet. To set up the TV table stand, please carry out the installation according to the instructions below. Always unplug the AC cord first when installing or removing the stand.

Important Precaution:

• Place the TV face down on a soft cloth or cushion to prevent the panel from being damaged. The panel can be scratched easily.

• Choose an absolutely flat surface to place the TV on.

• Use a soft cloth or cushion to face the TV panel.

• Do not put the TV on the table directly.

Installation Steps:

Step 1. Lay the TV face down on a soft, flat surface as described above.

Step 2. Take the neck. Align the screw holes of the neck and the TV. Insert the 6 Pedestal Screws (M4 x 15mm, Part# RS01TM415H) into the 6 holes on the neck and tighten them.

Step 3. Take the base. Align the four holes of the base and the four screw holes of the neck. Insert the base to the neck, and then insert the 4 Pedestal Screws (M4 x 14mm, Part# RS01PWA414HT) and tighten them.

The picture quality depends on the type of connection used. Please refer to the table below for connection advice.

To select an input source, press the [INPUT] button on the remote control to display the input list. Use the up/down arrow to highlight TV, AV, Component, HDMI1, HDMI2, Roku, or USB input, and then press OK to choose.

Step 1. Remove the battery compartment cover from the back of the remote control by lifting the cover.

Step 2. Insert 2 AAA batteries, making sure the polarities (+ and -) are aligned correctly.

Step 3. Replace the cover.

CAUTION:

• Used batteries should be recycled.

• Keep out of children’s reach.

• Do not use new and old batteries together.

• Change both batteries at the same time.

• When not using the remote control for a long time, remove the batteries from the unit.

If it is the first time you turn on your TV, or you have done the Clear Channel List option, the initial setup menu appears automatically.

Step 1. Please select Menu Language. Press the up/down arrow to select the language you need. Available languages are English, Spanish, and French.

Step 2. Please select the TV installation mode. Press the up/down arrow to select the mode you need: Home or Retail. If you select Home mode, continue to step three. If you select Retail mode, please refer to step four.

Step 3. Please choose between Power Saving and Dynamic mode. You can save more energy with Power Saving.

Step 4. To choose your TV tuner signal type, press the up/down arrow to select the signal type: Air or Cable. Note: please select the TV signal type according to the antenna or cable closed circuit TV you use.

Step 5. If you accomplish the initial setup, the TV will search for channels automatically.

What to notice:

1. The channel search access starts from the Analog TV channel searching and ends at Digital TV channel searching.

2. The channels that have been found will be stored automatically.

3. You can press the MENU button to skip analog/digital channel searching.

4. You can press the OK button to end the channel searching.

POWER: Turns the TV on or off.

EPG/DISPLAY: Shows Electronic Program Guide and displays the DVD information.

ROKU: Shortcut to Roku Input.

(Back Arrow): Return to previous screen.

Roku (Home): Return to Roku Home screen and exits the current menu or function.

Roku Arrows (Up/Down/Left/Right): Uses the four arrows to highlight different items in the TV menu or change the value. The up/down arrow can also work as CH▲/CH▼ button, and the left/right arrow can also work as VOL-/VOL+ button.

Roku OK: Enter and confirm button.

MENU: Accesses the Main Menu, or returns to the upper level of a sub-menu.

Roku (Asterisk): View more options of Roku mode.

VOL+ or VOL-: Increase/Decrease the volume of your TV.

CH(▲) or CH(▼): Scans up or down through the current channel list. Press once to change the channel up or down; press and hold to continue changing channels.

Numeric Buttons: Use these buttons to enter numbers.

. (Dot): To enter a digital channel with a sub-channel, enter the main channel; then, press this button to enter the sub-channel and press OK.

MUTE: Reduces the TV volume to its minimum level. Press again to restore the volume.

INPUT: Accesses the available input channels (TV, AV, Component, HDMI 1/2, Roku, USB). Use the arrows to highlight options, and press OK to select.

Roku Buttons (Rewind, Play/Pause, Fast Forward, etc.): These buttons are for Roku function control.

* Note: the keys not listed are for other purposes, they are not available for this TV model.