PURE AIR5 PRO (01) PDF Document

Read the following carefully and keep for future reference:

• This e-scooter is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the scooter.

• WARNING: Keep plastic covering away from children to avoid suffocation.

• The maximum load is 120kg.

• WARNING: For the purposes of recharging the battery, only use the detachable supply unit provided with this appliance.

• This e-scooter contains batteries that are only replaceable by skilled persons.

• Only Charge the battery between 5-40°C.

• Maximum charging voltage is 42V DC, 3A.

The package for your PURE AIR5 PRO contains:

• 1x Pure Air5 Pro

• 1x Charger

• 1x User manual

• 1x Allen key (3mm)

• 4x M5 countersunk bolts

Follow these simple set-up instructions:

1. Set up in box: Keep the e-scooter within the opened box during set up. This will keep it firmly in place for the next steps.

2. Raise the stem: Remove any remaining protective packaging from the e-scooter, then unfold it to its upright position, making sure the latch is down.

3. Secure the latch: Lift the latch mechanism until it clips securely into the stem. Warning! Do not ride the scooter if the latch is loose.

4. Lift the handlebar: Lift the handlebar onto the stem ensuring the internal wires are not trapped and the external brake cable is not twisted.

5. Fix the handlebar: Rotate the handlebar to align the holes in the stem with the handlebar. Locate the stem bolts (within the sealed package), and insert them loosely into the stem bolt recesses.

6. Tighten the bolts: Use the correctly-fitting Allen key supplied to tighten the bolts. Don’t tighten each screw all the way in one go.

7. Fully charge: Charge your e-scooter until the charger status light changes from red to green.

8. Tyre pressure: Check the tyres are inflated to the optimum pressure of 36 PSI / 2.5 Bar. Always use the valve extender with your pump. You will damage the tyre valves if you do not.

1. First, turn on your e-scooter by pressing and holding the central multifunction button for 2 seconds. The display will switch on.

2. To start riding, lift up the kickstand, place one foot on the deck and push against the floor with your other foot to propel you forwards.

3. After you’ve pushed yourself forwards, press the throttle with your thumb steadily to start accelerating. You will need to achieve a speed of 3km/h before the throttle will engage.

4. Steer by turning the handlebars left and right. The steering mechanism is sprung-loaded to help it return to centre, and to make it easier to steer during prolonged use.

5. You can slow down the e-scooter by pulling the brake lever. Braking activates both the electrical rear brake and the front drum brake.

6. To come to a stop, slow to almost a standstill. Then, place one foot on the ground, leaning slightly onto that foot as you come to a complete stop.

You can connect to your Bluetooth-enabled PURE AIR5 PRO using the app for iOS and Android devices. Use the Pure app to unlock additional features:

• Lock your e-scooter to prevent unauthorised use. The PIN is set to 888888 by default. Please ensure you change this to something unique and memorable to you.

• Change the units for the speedometer between km/h and mph.

• Turn on the Cruise control. This allows you to release the throttle while riding on longer journeys.

• Keep your tyres inflated: Your tubeless tyres naturally leak air pressure over time. Pump up your tyres to 36psi / 2.5 bar before each ride to get fewer punctures and better e-scooter performance.

• Maximise your e-scooter range: Fully charge your new e-scooter until the light on your charger goes green. Try to ride it until the battery is nearly empty. Then fully re-charge the battery back to 100%. Your battery range will now be maximised.

• Ride safely & responsibly: Wear a helmet, use your lights and indicators, and respect local laws.

• Select your maximum speed: Double press the power button to cycle through the 3 speed modes (indicated by the ‘S’ on screen).

• Regular maintenance: Maintaining your PURE AIR5 PRO regularly, by following the steps in this user manual helps reduce the risk of issues that would affect your e-scooter’s performance.

Turn on/off: Long Press on the multifunction button for 2 seconds. The scooter turns off after 5 minutes of inactivity.

Headlights on/off: Short press on the multifunction button.

Change drive mode: Double press on the multifunction button. This cycles through all 3 drive modes (Normal, High, Pedestrian).

Turning on/off: To turn the e-scooter on or off, press and hold the multifunction button for 2 seconds. After 5 minutes of inactivity when switched on, the e-scooter will automatically turn itself off to conserve the battery.

Headlights: When the e-scooter is switched on, a short press of the multifunction button will turn the headlights off and on.

Indicators: Indicator lights are triggered by a press of the left or right indicator buttons. Green arrows in the top corners of screen flash in sync with the indicators. Indicator lights are cancelled with a second short press of the button. Indicators automatically self-cancel after 30 seconds. (*Indicators on selected models only).

Cruise control: Cruise control is turned off by default, and can only be turned on via the mobile app. When cruise control is enabled, the icon flashes white. Holding the throttle at a constant speed for 5s will activate cruise control. The icon will show solid white and two beeps will occur. Cruise control is deactivated by pressing the brake or throttle and is signalled by a single beep.

The drive mode is displayed with the ‘S’ icon above the speed display. The first time you use the e-scooter, it is set to the ‘normal’ mode. Double pressing of the multifunction button will enable you to cycle through the drive modes. The chosen drive mode is saved when the e-scooter is turned off.

The remaining charge level is indicated with the battery status, positioned under the speed display. The status is split into five bars as shown below:

• 5 bars: 100 – 81%

• 4 bars: 80 – 61%

• 3 bars: 60 – 41%

• 2 bars: 40 – 21%

• 1 bar: 20 – 11%

• Flashing bar: 10 – 0%

Before Charging:

• If you notice any damage on the charger or cables, do not use it.

• Only use the original charger provided with this e-scooter or a genuine replacement.

• Allow the scooter to cool down before charging.

How to charge your e-scooter:

• Fully charge the battery before riding the e-scooter for the first time.

• The maximum charging voltage is 42V DC, 3A.

• While charging, all normal e-scooter functions are disabled. When you press the multifunction button, a charging battery indicator will show.

• When the light on the charger changes from red to green, the charge cycle has completed.

• Unplug the charger when charging is finished.

Where to charge your e-scooter:

• Only charge the e-scooter in temperatures between 5°C and 40°C.

• Always charge the battery in a dry and clean environment, out of direct sunlight.

• Always charge the e-scooter in a safe and well-ventilated area (e.g. away from flammable materials, children and pets). If possible, store in a garage or shed.

• Do not leave the e-scooter unattended while charging.

• Never charge the product while you are asleep.

• Never store or charge your scooter in fire escape routes.

• E-Scooter not intended for use at elevations higher than 2000m above sea level.

• If you are not going to use your e-scooter for a long period, we recommend giving the e-scooter a full charge at least once every month.

• Longer charging times or poor performance indicate battery issues.

WARNING: Risk of fire – no user serviceable parts. Do not try to repair your battery or charger. This e-scooter contains batteries that are only replaceable by skilled persons.

If your scooter exhibits any of the following signs: Smoke, Excessive Heat, Burning Smell, Hissing or Crackling Sounds, Leaking/Bulging; follow these steps:

• Stop using immediately.

• If safe, disconnect the charger and remove the scooter from your home.

• Evacuate and contact emergency services.

This e-scooter is designed to be used in an outside environment and is waterproof to an IP65 rating. You may use the e-scooter in the rain and ride through puddles, but should avoid partial or total submersion.

• 6: Totally dust tight. Full protection against dust and other particulates, including a vacuum seal, tested against continuous airflow.

• 5: Protection against low-pressure jets (6.3mm) of directed water from any angle (limited ingress permitted with no harmful effects).

Before you ride it each time:

• Check that all screws and bolts are tight, especially those of the handlebar, the hinge, the brakes and the front and rear wheel.

• Check your tyres and pressures, ensuring that they’re in the optimum range stated on the side of the tyre wall (between 36-50psi).

• When you brake, your e-scooter uses regenerative braking on the rear wheel to recharge its battery. However, if your battery is fully charged, particularly at the start of a downhill ride, regenerative braking is reduced to protect the battery. Always ensure the drum brake on the front wheel is properly adjusted before you set off, guaranteeing consistent braking throughout your journey.

Store the e-scooter in a dry place, away from direct sunlight. If left unused, recharge the battery every month to maintain longevity of the battery and to avoid damage.

Never store the e-scooter in temperatures above 50°C, or below -20°C, as this will cause damage. The capacity of the battery decreases with cold temperatures, impacting the range.

In order to avoid corrosion, you should clean and dry your e-scooter after every use.

• Use a slightly damp sponge or cloth for cleaning and dry afterwards with a towel.

• DO NOT use excessive water or harsh substances such as degreasers as they may result in damage to the e-scooter and its battery.

• NEVER use a pressure washer to clean the e-scooter.

Sometimes your e-scooter may enter a deep sleep mode. To awaken it, fully charge your e-scooter:

• Plug the charger into your e-scooter, the charger light should change from green to red.

• Charge your e-scooter fully. When the light on the charger changes from red to green, the charge cycle has completed.

• This e-scooter is designed and intended for personal use for short distance travel on tarmac and paved surfaces that provide necessary grip for tyres, and are typically used by personal mobility devices, such as bicycles and skateboards.

• This e-scooter should not be used on loose surfaces such as gravel or sand, or slippery surfaces such as wet stone, cobbles, ice and snow, or metal.

• Avoid pot holes and impact with pronounced edges.

• This e-scooter should only be used by one person at a time.

• This e-scooter may only be used by those over the age of 16 years.

• You must always follow the laws in the area in which you ride this e-scooter.

• The user’s riding weight should not exceed 120kg, including backpacks and other items that might be carried on the rider.

• Any load attached to the handlebar will affect the stability of the vehicle.

• The maximum user height is 2m.

• This scooter should not be used on off-road surfaces.

1. Check the brakes, wheels and tyres before every ride. Never ride with damaged brakes. You can slow down the e-scooter by using the brake lever on the left side of the handlebar. The brake lever activates both the drum front brake and the electric brake of the rear wheel at the same time. Squeeze the brake lever gently to effectively use the brake in a stable way, and be aware that braking distances may be extended in wet weather.

2. Before each ride, ensure the steering system is working and that the latch for the folding mechanism is in place correctly, with the handle firmly tightened.

3. Wear flat closed shoes when using the e-scooter. Always keep both feet on the e-scooter while riding, unless you are just starting to accelerate or about to stop. Wait until you have come to a complete standstill before you get off the e-scooter.

4. We recommend wearing protective equipment (e.g. helmet, kneepads, etc.) when riding the e-scooter.

5. Hold the handlebar firmly with both hands at all times when riding.

6. It is your responsibility to ride the e-scooter using good judgement in order to reduce the risk of injury. Do not use the e-scooter when under the influence of drugs, alcohol or medication that may impair your judgement. Use common sense to detect and avoid hazards that pose a risk to you, others and others’ property while you use the e-scooter.

7. The e-scooter is designed for outdoor use on smooth, stable surfaces. You should ride appropriately for the conditions you are riding in, and anticipate potential hazards at all times (e.g. light, weather, other traffic participants, etc.)

8. Both tyres must be in contact with the ground at all times in order to be able to provide adequate grip to ride safely (conditions permitting).

9. If your e-scooter breaks or shows wear, we strongly recommend having a service carried out.

• Dismount your e-scooter when entering a pedestrian zone and cross the protected passages while walking.

• Do not change the use of this e-scooter from its intended use.

• This vehicle is not intended for acrobatic use.

• Regularly check the tightness of the various bolted elements, in particular the wheel axles, the folding system, the steering system and the brake system.

• Eliminate any sharp edges caused by use.

• The kickstand must be folded up before stepping onto the scooter. Never step on the mudguards.