PHILIPS 27B2N3500J (01) PDF DOCUMENT

To ensure safe operation of your PHILIPS 27B2N3500J monitor, please follow these precautions:

Operation:

• Keep the monitor out of direct sunlight and away from oil, as oil can damage the plastic cover and void the warranty.

• Do not block the ventilation holes in the cabinet and remove any objects that could fall into them.

• When positioning the monitor, ensure the power plug and outlet are easily accessible.

• If you turn off the monitor by detaching the power cord, wait 6 seconds before reattaching it for normal operation.

• Always use the approved power cord provided by Philips. If it is missing, contact your local service center.

• Operate the monitor using the specified power supply. Using an incorrect voltage can cause malfunction, fire, or electric shock.

• Protect the power and signal cables. Do not pull, bend, or place heavy objects on them.

• Do not subject the monitor to severe vibration or high-impact conditions.

• To avoid potential damage like panel peeling, ensure the monitor does not tilt downward by more than -5 degrees. Damage from exceeding this tilt angle is not covered under warranty.

• Do not knock or drop the monitor during operation or transportation.

Maintenance:

• To protect the monitor from damage, do not put excessive pressure on the LCD panel. When moving it, grasp the frame to lift; do not lift by placing your hand or fingers on the panel.

• Unplug the monitor if you will not be using it for an extended period.

• To clean the monitor, unplug it and use a slightly damp cloth. The screen can be wiped with a dry cloth when the power is off. Never use organic solvents, such as alcohol or ammonia-based liquids.

• To avoid shock or permanent damage, do not expose the monitor to dust, rain, water, or excessive moisture.

• If the monitor gets wet, wipe it with a dry cloth as soon as possible.

• Do not store or use the monitor in locations exposed to heat, direct sunlight, or extreme cold.

Excessive use of your PHILIPS 27B2N3500J can cause eye discomfort. It is recommended to take shorter, more frequent breaks. For example, a 5-10 minute break after 50-60 minutes of continuous screen use is better than a 15-minute break every two hours. To prevent eye strain:

• Look at objects at varying distances after a long period of focusing on the screen.

• Blink consciously while you work.

• Gently close and roll your eyes to relax.

• Reposition your screen to the appropriate height and angle.

• Adjust the brightness and contrast to an appropriate level.

• Adjust the environment lighting to be similar to your screen’s brightness. Avoid fluorescent lighting and surfaces that reflect too much light.

• See a doctor if your symptoms worsen.

The PHILIPS 27B2N3500J also includes features designed to reduce eye fatigue:

• Anti-glare screen: Reduces annoying and distracting reflections.

• Flicker-free technology: Regulates brightness to reduce flicker for more comfortable viewing.

• EasyRead mode: Provides a paper-like reading experience for long documents.

“Burn-in,” “after-imaging,” or “ghost imaging” is a known phenomenon in LCD panel technology. It occurs when a still or static image is displayed for an extended period. In most cases, the effect will gradually disappear after the power has been switched off.

To prevent this on your PHILIPS 27B2N3500J, you should:

• Always activate a moving screen saver program when you leave your monitor unattended.

• Always activate a periodic screen refresh application if your monitor will display unchanging static content.

Failure to activate a screen saver or a periodic screen refresh application may result in severe symptoms that will not disappear and cannot be repaired. This type of damage is not covered under your warranty.

Follow these steps to install the base on your PHILIPS 27B2N3500J monitor:

1. To protect the monitor and avoid scratches or damage, place the monitor face down on a soft, cushioned surface.

2. Hold the stand with both hands:

(1) Gently attach the base to the stand.

(2) Use your fingers to tighten the screw located at the bottom of the base, securing it tightly to the stand.

(3) Gently attach the stand to the VESA mount area on the back of the monitor until the latch locks the stand in place.

1. Connect the power cord firmly to the back of the PHILIPS 27B2N3500J display.

2. Turn off your computer and unplug its power cable.

3. Connect the monitor’s signal cable (HDMI or DisplayPort) to the video connector on the back of your computer.

4. Plug the power cord of your computer and your monitor into a nearby outlet.

5. Turn on your computer and monitor. If the monitor displays an image, the installation is complete.

The On-Screen Display (OSD) allows you to adjust screen performance and select functions. To navigate the OSD menu on your PHILIPS 27B2N3500J:

1. Press the /OK button to access the main OSD menu.

2. Use the Up and Down arrow buttons on the front bezel of the monitor to move the cursor and highlight different options.

3. Press the OK button to confirm a choice or enter a sub-menu.

4. Use the Left arrow button to return to the previous menu level.

There are two ways to perform firmware updates on your PHILIPS 27B2N3500J monitor:

1. Over-the-air (OTA): This update is done through the SmartControl software. SmartControl is an additional software that helps control the picture, audio, and other on-screen graphic settings. In the “Setup” section of the software, you can check your current firmware version and upgrade if necessary. A network connection is required for this method.

2. On-the-go (OTG): This monitor has an OTG function that allows for direct firmware updates via a USB stick. Please contact local customer service to obtain relevant information and assistance with this type of update.

The stand for the PHILIPS 27B2N3500J allows for the following physical adjustments:

• Tilt: -5 to +30 degrees

• Swivel: -180 to +180 degrees

• Height adjustment: 150mm

• Pivot: -90 to +90 degrees (for portrait mode)

Warning: To avoid screen damage such as panel peeling, ensure the monitor does not tilt downward by more than -5 degrees. Do not press on the screen while adjusting the angle; grasp only the bezel.

Before disassembling the display base, please follow these instructions to avoid damage or injury:

1. Place the monitor face down on a smooth surface. Be careful not to scratch or damage the screen. Then, lift the monitor stand.

2. While keeping the release button pressed, tilt the base and slide it out from the stand arm.

3. Press both corners of the VESA Cover, and the other side of the cover will pop out.

4. Remove the VESA Cover.

The monitor accepts a 100mm x 100mm VESA-compliant mounting interface with M4 screws.

SmartImage is a Philips technology that provides presets to optimize the display for different types of content by dynamically adjusting brightness, contrast, color, and sharpness in real-time.

To enable SmartImage, press the SmartImage button to launch the on-screen display. Keep pressing the up/down arrows to toggle between modes, and press “OK” to confirm.

The available modes are:

• EasyRead: Improves reading of text-based applications like PDF ebooks by increasing contrast and boundary sharpness.

• Office: Enhances text and dampens brightness to increase readability and reduce eye strain for office applications.

• Photo: Combines color saturation, dynamic contrast, and sharpness enhancement to display photos and other images with outstanding clarity in vibrant colors.

• Movie: Ramped up luminance, deepened color saturation, dynamic contrast, and razor sharpness to display every detail in darker areas of videos without color washout.

• Game: Turns on the over-drive circuit for the best response time, reduces jaggy edges for fast-moving objects, and enhances the contrast ratio for bright and dark schemes.

• Economy: Adjusts brightness and contrast, and fine-tunes backlighting for everyday office applications and lower power consumption.

• Off: No optimization by SmartImage.

SmartContrast is a unique technology on the PHILIPS 27B2N3500J that dynamically analyzes the displayed content and automatically optimizes the monitor’s contrast ratio for maximum visual clarity and viewing enjoyment. When activated, it will analyze the content you are displaying in real-time to adjust colors and control backlight intensity. This function dynamically enhances contrast for a great entertainment experience when viewing videos or playing games, and it also helps save on energy costs.

The PHILIPS 27B2N3500J works best at its native resolution of 2560 x 1440. For best display quality, please follow this resolution recommendation. The following table lists the preset modes:

If you have a VESA DPM compliance display card or software installed on your PC, the PHILIPS 27B2N3500J monitor can automatically reduce its power consumption when not in use. If an input from a keyboard, mouse, or other input device is detected, the monitor will ‘wake up’ automatically. The following table shows the power consumption for this feature:

These measurements were taken with: Native resolution: 2560 x 1440, Contrast: 50%, Brightness: 70%, Color temperature: 6500k with full white pattern, Audio and USB Inactive (Off).

Philips strives to deliver high-quality products. However, pixel or sub-pixel defects on TFT Monitor panels can sometimes be unavoidable. The policy defines acceptable defect levels for repair or replacement under warranty. A pixel is composed of three sub-pixels: red, green, and blue.

Types of Pixel Defects:

• Bright Dot Defects: Sub-pixels that are always lit (‘on’). These include one lit red, green, or blue sub-pixel; two adjacent lit sub-pixels (Purple, Yellow, or Cyan); or three adjacent lit sub-pixels (one white pixel).

• Black Dot Defects: Sub-pixels that are always dark (‘off’).

Acceptable Defect Levels:

Note: 1 or 2 adjacent sub-pixel defects = 1 dot defect.

• Make sure the power cord is plugged into the power outlet and the back of the monitor.

• First, ensure that the power button on the front of the display is in the OFF position, then press it to the ON position.

• Make sure the computer is turned on.

• Make sure the signal cable is properly connected to your computer.

• Make sure the monitor cable has no bent pins on the connecting side. If it does, repair or replace the cable.

• The Energy Saving feature may be activated. Check if the screen says “Check cable connection.”

• Do not perform any troubleshooting steps.

• Disconnect the monitor from the main power source immediately for safety.

• Contact Philips customer service representative immediately.

• Adjust the contrast and brightness settings using the On-Screen Display (OSD).

• If the text is fuzzy or the image is distorted, set the PC’s display resolution to the same mode as the monitor’s recommended native resolution (2560 x 1440).

The recommended resolution for the PHILIPS 27B2N3500J is 2560 x 1440. To fix this error, follow these steps:

1. Unplug all cables, then connect your PC to the display that you used previously.

2. In Windows, go to Settings/Control Panel, then select the Display icon. Inside the Display Control Panel, select the ‘Settings’ tab. Under the ‘desktop area’ box, move the sidebar to 2560 x 1440 pixels.

3. Open ‘Advanced Properties’ and set the Refresh Rate to 60 Hz, then click OK.

4. Restart your computer and repeat steps 2 and 3 to verify that your PC is set at 2560 x 1440.

5. Shut down your computer, disconnect your old monitor, and reconnect your PHILIPS 27B2N3500J monitor.

6. Turn on your display and then turn on your PC.

The available resolutions are determined by your video card/graphic driver and the display. You can select the desired resolution under the Windows® Control Panel within the “Display properties”. For the best display quality on your PHILIPS 27B2N3500J, it is recommended to use the native resolution of 2560 x 1440.

Simply press the /OK button, then navigate to ‘Setup’ > ‘Reset’ to recall all the original factory settings.

For normal cleaning, use a clean, soft cloth. For extensive cleaning, please use isopropyl alcohol. Do not use other solvents such as ethyl alcohol, ethanol, acetone, hexane, etc.

Yes, you can change your color settings through the OSD control:

1. Press “OK” to show the OSD menu.

2. Press the “Down Arrow” to select the “Color” option, then press “OK”.

There are three settings available:

• Color Temperature: Options include Native, 5000K, 6500K, 7500K, 8200K, 9300K, and 11500K. Lower temperatures appear “warm” (red-white), while higher temperatures appear “cool” (blue-white).

• sRGB: This is a standard setting for ensuring correct color exchange between different devices (e.g., digital cameras, monitors, printers).

• User Define: Allows you to choose your preferred color setting by adjusting red, green, and blue values.

• To lock the OSD: Press and hold the /OK button while the monitor is off, and then press the power button to turn the monitor on.

• To unlock the OSD: Press and hold the /OK button while the monitor is off, and then press the power button to turn the monitor on.