PHANTEKS ENTHOO LUXE PH-ES614L (01) PDF Document

Free English PHANTEKS ENTHOO LUXE PH-ES614L (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.

CLICK HERE TO DOWNLOAD PHANTEKS ENTHOO LUXE PH-ES614L (01) PDF DOCUMENT

If this is not the document you want for this product, click here to see if we have any other documents for this product.

How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.

What are the core technical specifications for the PHANTEKS ENTHOO LUXE PH-ES614L?

The PHANTEKS ENTHOO LUXE PH-ES614L is a full tower case featuring aluminum faceplates and a steel chassis. It supports ATX, EATX, mATX, and SSI EEB motherboard form factors.

Dimension (W x H x D)	235 mm x 560 mm x 550 mm
Front I/O	2x USB 3.0, 2x USB 2.0, Mic, Headphone, LED Switch
Side Window	Yes, split-window design
Expansion Slots	8
External 5.25 inch Bays	3
Internal 3.5 inch Bays	6 (2x 3HDD cages)
Internal 2.5 inch Bays	8 (2x SSD Brackets)

Clearance specifications for the PHANTEKS ENTHOO LUXE PH-ES614L:

Graphic card	347 mm (472 mm without HDD cages)
CPU cooler	193 mm
Cable management	27 mm (39 mm at PSU area)
Radiator Clearance	65 mm to motherboard

What are the cooling and liquid cooling capabilities of the PHANTEKS ENTHOO LUXE PH-ES614L?

The PHANTEKS ENTHOO LUXE PH-ES614L supports various fan and radiator configurations across its chassis:

Fan Compatibility Table:

Location	120 mm	140 mm	200 mm
Front	2x	2x	1x (included)
Top	3x	3x (1x included)	1x
Rear	1x	1x (1x included)	–
Bottom	2x	1x	–
HDD	2x	–	–

Liquid Cooling Radiator Compatibility:

Location	120 mm radiator	140 mm radiator
Front	Up to 240	–
Top	Up to 360	Up to 420
Rear	120	140
Bottom	Up to 240	140

Which accessories are included with the PHANTEKS ENTHOO LUXE PH-ES614L?

The PHANTEKS ENTHOO LUXE PH-ES614L includes a variety of screws and mounting hardware for assembly:

Item	Description	Use
Screw M3 x 5mm	Motherboard/ODD/SSD	23
Stand Off Screws	Motherboard	2
Screw 6-32 x 6mm	PSU, Brackets	5
Thumb Screws 6-32 x 6mm	PSU, Brackets, HDD cages	3
Screw 6-32 x 31mm	HDD fans, 200mm fan (top)	10
Screw 5 x 10KT	Fan installation	12
CM6 #11	HDD	12
Screw M4 x 8mm	Reservoir	8
KM6 #6	Reservoir bracket	3
PWM6# x 6mm	Hook-n-Loop Screw	2
CM6 #5	Pumpbracket upgrade	5
150mm Zip Tie	Cable management	10
188 x 10 x 1.8mm	Hook n Loop (long)	1
110 x 10 x 1.8mm	Hook n Loop (short)	1

How do I operate the LED control and I/O ports on the PHANTEKS ENTHOO LUXE PH-ES614L?

The front and top view of the PHANTEKS ENTHOO LUXE PH-ES614L I/O panel includes the following ports: USB 3.0 (1), USB 2.0 (2), Microphone (3), Headphone (4), Power Reset (5), LED Switch (6), and the Power Button/HDD LED (7).

To operate the LED Control:

To turn the LED on or off, hold the LED Switch button down.

For color selections, press the LED Switch button briefly to cycle through the desired colors.

What is the procedure for disassembling the chassis of the PHANTEKS ENTHOO LUXE PH-ES614L?

Disassembling the PHANTEKS ENTHOO LUXE PH-ES614L requires following a specific order of screw removal:

Step 1. Top Chassis Panel Disassembly: Remove the 15 screws identified on the top, rear, front, and side views to take the top chassis panel off.

Step 2. HDD Chassis Panel Disassembly: After removing the top chassis panel, unscrew the 9 screws indicated to remove the HDD panel.

Step 3. Optical Bay Chassis Panel Disassembly: After removing both the top and HDD panels, unscrew the 5 screws indicated to remove the Optical bay.

How do I remove the panels from the PHANTEKS ENTHOO LUXE PH-ES614L safely?

To remove the side panels of the PHANTEKS ENTHOO LUXE PH-ES614L, unscrew the 4 thumb screws located at the rear of the chassis and pull the panels away.

To prevent damage to the other panels, follow these steps in order:

Step 1. Pull the front panel outward to remove it. Use caution as Power LED wires are attached to the front panel.

Step 2. Pull the top panel upward to remove it.

How is the motherboard installed in the PHANTEKS ENTHOO LUXE PH-ES614L?

Motherboard installation for the PHANTEKS ENTHOO LUXE PH-ES614L involves two main steps:

Step 1. Prepare Standoffs: Standoff screws are pre-installed for ATX motherboards. Extra standoffs are required and must be installed if using an E-ATX motherboard.

Step 2. Mounting: Secure the motherboard to the standoffs using the provided M3 screws.

How do I install the Power Supply (PSU) and its cover in the PHANTEKS ENTHOO LUXE PH-ES614L?

Follow these steps for PSU installation in the PHANTEKS ENTHOO LUXE PH-ES614L:

Step 1. Remove PSU Cover: Unscrew the thumb screws, pull the cover out, and then lift up on the right side to remove it.

Step 2. Install PSU: Place the PSU into the chassis and use the 4 provided screws to secure it in place from the rear of the case.

Step 3. Reinstall PSU Cover: Align the cover to the three rubber grommets and slide it in. Use the provided thumb screws to lock the cover in place.

How should I clean the dust filters on the PHANTEKS ENTHOO LUXE PH-ES614L?

To maintain the PHANTEKS ENTHOO LUXE PH-ES614L, the filters should be cleaned regularly:

Removal: To remove the bottom and front dust filters, slide them out from the case. For the top filter, push down on the indicated area to release it.

Cleaning: Run slow-moving water through the filters. You must ensure the filters are completely dry before reinstalling them into the chassis.

How are SSDs and Hard Drives installed in the PHANTEKS ENTHOO LUXE PH-ES614L?

The PHANTEKS ENTHOO LUXE PH-ES614L offers multiple mounting options for drives:

SSD Installation:

Option 1 (Slide In): Slide the SSD into the bracket and screw it in from the side to lock it in place.

Option 2 (Drop N Lock): Align the corner of the bracket to the guide and drop it down into the mounting location to lock.

3.5 inch Hard Drive Installation: Place the hard drive into the tray and push in the arms to lock. Align the tray to the HDD cage and slide it in.

2.5 inch Hard Drive Installation in Trays: Align the SSD onto the mounting holes in the tray and screw it in from the bottom.

How do I set up the PWM Hub in the PHANTEKS ENTHOO LUXE PH-ES614L?

The PWM hub in the PHANTEKS ENTHOO LUXE PH-ES614L functions optimally when modulated by a PWM signal from the motherboard.

Connecting to CPU_FAN: Connect the hub’s 4-pin connector to the CPU_Fan connector on the motherboard. This ensures a true PWM signal modulation. Connect the SATA 12V power cable to the power supply to provide power to the hub.

Connecting to other 4-pin headers: If connected to a non-CPU_Fan 4-pin header, the motherboard may modulate by voltage instead of a true PWM signal. In this specific scenario, the 12V SATA power cable must NOT be used, as it will interfere with voltage regulation and cause fans to run at full RPM. In this configuration, the hub is limited to a total device consumption of 30W.

Important Note: The motherboard can only read 1 RPM signal. It will only read the RPM from the device connected to “Fan 1” on the hub. All other connected fans will be regulated according to the signal from Fan 1. Do not connect a Y-splitter to the Fan 1 header.

How do I install the pump and reservoir brackets in the PHANTEKS ENTHOO LUXE PH-ES614L?

The PHANTEKS ENTHOO LUXE PH-ES614L includes dedicated brackets for water cooling components:

Reservoir Bracket: Align the reservoir bracket to the mounting hole and screw into the top of the bracket. Use the provided 2x screws to lock the reservoir in place.

Pump Bracket: The pump bracket features universal mounting (6#-32 and M4 holes) with rubber dampers. Place the pump bracket onto the HDD cage stand and use screws to lock it in place.