Free English PANDA PAN356HB (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD PANDA PAN356HB (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
How do I install the bottom cover on the PANDA PAN356HB?
Put the machine down on its side on a soft surface. Align the screw holes on the bottom cover with the machine, ensuring the arrow is facing the front, and secure it using the provided tapping screws.
How should I position the PANDA PAN356HB for proper operation?
Ensure there is a distance of more than 50mm between the washing machine and the wall. If the floor is slanted or rough, adjust the adjustable feet to ensure the machine is stable and level. You can use a tied thread with a plumb to check if the machine is level.
What are the requirements for the drainpipe of the PANDA PAN356HB?
The drainpipe must be hung during use, at a height between 28 to 48 inches to avoid leakage or stopping. You can adjust the situation of the elbow bend pipe to change the height, and you must ensure the drainpipe is not extruded to allow it to drain smoothly.
How do I connect the water inlet hose to the PANDA PAN356HB?
Ensure the water absorption cushion is in place, then put the inlet hose nut on the inlet valve connector and fasten it gently. To connect the hose to the tap, pull back on the white ring of the adapter to free the fitting, attach it to the faucet, and then connect the two parts of the adapter together. Finally, push the slider on the inlet hose connector to attach it to the machine until a click sound is heard.
What is the recommended water temperature for the PANDA PAN356HB?
The temperature of the water used in the PANDA PAN356HB should be less than 50 degrees Celsius.
How do I use detergent with the PANDA PAN356HB?
Put the detergent powder into the detergent dispenser in the tub, then close the wash lid. It is recommended to use low sudsing detergent powder. If you need to dissolve the powder first, use low water level and run the machine for 30 seconds, or dissolve the powder in a container with warm water (30 degrees Celsius) before pouring it into the machine.
How do I use softener in the PANDA PAN356HB?
Put the softener into the softener box before the machine runs. You may need to turn the inner tub to find the softener box at the side. The machine will automatically dispense the softener during the rinsing wash. Do not let the softener sit for too long as it may solidify.
How can I set the child lock on the PANDA PAN356HB?
While the machine is running, press and hold the water level/spin and program/delay buttons at the same time for over 3 seconds to activate the child lock. Perform the same action again to cancel the child lock.
What maintenance is required for the lint filter on the PANDA PAN356HB?
It is necessary to use the lint filter during every wash. After washing, press the release button to pull out the lint filter, open it, wash away the accumulated lint, and then reinstall it in the proper position.
What should I do if the PANDA PAN356HB displays error codes?
| Code | Possible Cause | Solutions |
|---|---|---|
| E0 | Top lid is open when preset is started | Close the top lid and clear the alarm |
| E1 | After draining 5 minutes, it still does not reach water level | Open top lid, check for drainage issues, and close the top lid |
| E2 | During the running of the program, the top lid is in the open state | Close the top cover and press the Start/Pause button |
| E3 | Spin does not balance | Open the top lid, rearrange the laundries to be balanced, close the top lid |
| E4 | After inlet 50 minutes still not reaching setting water level | Check water supply, ensure tap is open, close top lid |
| E5 | Top lid is opened after setting child-lock | Close the top lid and clear the alarm |
| E6 | Water level is more than overflowing water level | Drain the water until the level is within normal range |
| E7 | The input and output of the memory is abnormal | Close the top lid and clear the alarm |
| F1 | Water level sensor is wrong | Cut the power supply and contact a technician |
How can I troubleshoot basic issues with the PANDA PAN356HB?
| Problem | Possible Cause | Solutions |
|---|---|---|
| Control panel has no display | Plug is not inserted tightly, no electricity, or power switch off | Insert plug, check socket, press power switch |
| Inlet hose leaks | Hose connector or machine connector is loose | Install the inlet hose again and tighten the connector |
| It does not drain | Water outlet of drainpipe is higher than 1.2m or is blocked | Ensure drainpipe height is less than 1.2m, straighten or clean the drainpipe |
| It does not inlet | No water supply, tap is not open, or inlet hose is blocked | Check water supply, open the tap, or clean the inlet filter |
| Spin stops and begins to inlet during spin program | Laundries is too much or too little or machine is not stable | The machine will adjust automatically |
CLICK HERE TO DOWNLOAD PANDA PAN356HB (01) PDF DOCUMENT