FREE ENGLISH OPTONICA 7655 (01) PDF DOCUMENT.
FREE ENGLISH OPTONICA 7655 (01) PDF USER GUIDE.
FREE ENGLISH OPTONICA 7655 (01) PDF USER MANUAL.
FREE ENGLISH OPTONICA 7655 (01) PDF OWNER GUIDE.
FREE ENGLISH OPTONICA 7655 (01) PDF OWNER MANUAL.
FREE ENGLISH OPTONICA 7655 (01) PDF REFERENCE GUIDE.
FREE ENGLISH OPTONICA 7655 (01) PDF INSTRUCTION GUIDE.
FREE ENGLISH OPTONICA 7655 (01) PDF REFERENCE MANUAL.
FREE ENGLISH OPTONICA 7655 (01) PDF INSTRUCTION MANUAL.
FREE ENGLISH OPTONICA 7655 (01) PDF OPERATING INSTRUCTIONS.
CLICK HERE TO DOWNLOAD OPTONICA 7655 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What are the product specifications for the OPTONICA 7655 switch?
| Model | 7655; 7656 |
| Type | 1 Gang |
| Dimension | 86L x 86W x 15D(mm) |
| Life Time | >25,000 Times |
| Frequency | 433MHz |
| IP Rate | IP44 |
What are the product specifications for the OPTONICA 7655 controller?
| Type | (Wi-Fi) |
| Dimension | 43.8L x 43.8W x 22D(mm) |
| Max Load | AC110V-240V~ 50/60Hz, <150W (LED) |
| Frequency | 433MHz |
| IP Rate | IP20 |
How can I install the OPTONICA 7655 switch?
There are two methods to install the switch:
1. Use the double-sided tape to install.
2. Use the screws and anchors to install.
* The switch is available for portable use of indoor.
How do I wire the OPTONICA 7655 controller?
The controller should be wired between the main power lines (Neutral Wire and Live Wire) and the light fixture. The Neutral Wire connects to the ‘N’ input and output terminals, and the Live Wire connects to the ‘Li’ (Live in) and ‘Lo’ (Live out) terminals.
Caution: The controller will not work if the connection of input and output wires is wrong.
How do I pair the OPTONICA 7655 switch with the controller?
Be sure to pair the switch and controller before usage.
1. Hold the pairing button on the controller for 3 seconds.
2. Release the button once the LED flashes.
3. Press the kinetic switch.
4. The LED on the controller flashes once, indicating the pairing is completed.
How do I reset the OPTONICA 7655 controller?
1. Turn off the breaker, press the pairing button on the controller, and then power it on for 3 seconds.
2. The LED will flash.
3. Release the button. The reset is completed.
How do I use the dimming mode with the OPTONICA 7655 switch?
Press and hold the kinetic switch for 3 seconds to enter dimming mode. The light will gradually turn on from dark to bright, then cycle between bright and dark continuously until the switch is released.
What are the cautions for using the OPTONICA 7655 switch?
1. Avoid installing the switch on a metal surface, as that may seriously affect the operation range.
2. Range may vary dramatically in different environments.
What are the cautions for using the OPTONICA 7655 controller?
1. Range may vary dramatically in different environments.
2. The controller is not available to work with an air conditioner, pump, or any other appliance (Max Load Stated Above).
3. Be sure which one is the live wire before you shut down the power and install the controller.
CLICK HERE TO DOWNLOAD OPTONICA 7655 (01) PDF DOCUMENT