FREE ENGLISH OPTONICA 7656 (01) PDF DOCUMENT.
FREE ENGLISH OPTONICA 7656 (01) PDF USER GUIDE.
FREE ENGLISH OPTONICA 7656 (01) PDF USER MANUAL.
FREE ENGLISH OPTONICA 7656 (01) PDF OWNER GUIDE.
FREE ENGLISH OPTONICA 7656 (01) PDF OWNER MANUAL.
FREE ENGLISH OPTONICA 7656 (01) PDF REFERENCE GUIDE.
FREE ENGLISH OPTONICA 7656 (01) PDF INSTRUCTION GUIDE.
FREE ENGLISH OPTONICA 7656 (01) PDF REFERENCE MANUAL.
FREE ENGLISH OPTONICA 7656 (01) PDF INSTRUCTION MANUAL.
FREE ENGLISH OPTONICA 7656 (01) PDF OPERATING INSTRUCTIONS.
CLICK HERE TO DOWNLOAD OPTONICA 7656 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What are the specifications of the OPTONICA 7656 switch?
| Model | 7655; 7656 |
| Type | 1 Gang |
| Dimension | 86L x 86W x 15D(mm) |
| Life Time | >25,000 Times |
| Frequency | 433MHz |
| IP Rate | IP44 |
What are the specifications of the controller for the OPTONICA 7656?
| Type | (Wi-Fi) |
| Dimension | 43.8L x 43.8W x 22D(mm) |
| Max Load | AC110V-240V~ 50/60Hz, <150W (LED) |
| Frequency | 433MHz |
| IP Rate | IP20 |
How do I install the OPTONICA 7656 switch?
There are two methods to install the switch:
1. Use the double-sided tape to install.
2. Use the screws and anchors to install.
* The switch is available for portable use of indoor.
How do I wire the controller for the OPTONICA 7656?
The controller should be wired between the power source and the light fixture. Connect the Neutral Wire and Live Wire from the power source to the input side of the controller, and connect the corresponding wires from the light fixture to the output side of the controller.
Caution: The controller will not work if the connection of input and output wires is wrong.
How do I pair the OPTONICA 7656 switch with the controller?
Be sure to pair the switch and controller before usage.
1. Hold the pairing button on the controller for 3 seconds.
2. Release the button once the LED flashes.
3. Press the switch.
4. The LED on the controller flashes once, indicating pairing is completed.
How do I reset the controller for the OPTONICA 7656?
1. Turn off the breaker, press and hold the pairing button on the controller, and then power it on for 3 seconds.
2. The LED will flash.
3. Release the button. The reset is completed.
How do I use the dimming mode on the OPTONICA 7656?
Press and hold the kinetic switch for 3 seconds to enter dimming mode. The light will gradually turn on from dark to bright, then cycle by cycle between bright and dark continuously until the switch is released.
Can I control the OPTONICA 7656 with a smart device?
Yes, you can install the “Smart Life” app to control the lightings in the house.
What precautions should be taken when installing or using the OPTONICA 7656?
Switch Cautions:
1. Avoid installing the switch on a metal surface, as that may seriously affect the operation range.
2. The range may vary dramatically in different environments.
Controller Cautions:
1. The range may vary dramatically in different environments.
2. The controller is not available to work with an air conditioner, pump, or any other appliance (Max Load Stated Above).
3. Be sure which one is the live wire before you shut down the power and install the controller.
CLICK HERE TO DOWNLOAD OPTONICA 7656 (01) PDF DOCUMENT