Free English OKI DATA AMERICAS C5400N (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD OKI DATA AMERICAS C5400N (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
How do I physically install the duplex unit on the OKI DATA AMERICAS C5400N?
To install the duplexer, follow these steps:
1. Unpack the duplexer and remove the shipping materials.
2. Turn off the printer.
3. Insert the duplexer through the hinged door in the back of the printer.
4. Turn on the printer.
How can I verify that the duplex unit is installed correctly on the OKI DATA AMERICAS C5400N?
You can verify installation by printing the Menu Map using the following steps:
1. Press + one or more times until INFORMATION MENU appears on the display.
2. Press ENTER twice. The MenuMap prints.
3. Check to be sure that “DUPLEX installed” shows in the information at the top of the first page.
What should I do if “DUPLEX installed” does not appear on the Menu Map of the OKI DATA AMERICAS C5400N?
If “DUPLEX installed” is not shown on the Menu Map, turn off the printer and push firmly on the duplexer to be sure it is firmly seated in the printer. Then, turn on the printer and print the MenuMap again.
How do I change the default setting for Duplex to ON using the printer menu on the OKI DATA AMERICAS C5400N?
If you will always be using duplex printing, you can change the default setting via the control panel:
a. Press + until you see PRINT MENU on the display.
b. Press ENTER.
c. Press + until you see DUPLEX on the display.
d. Press ENTER.
e. Press + to change the setting from OFF to ON.
f. Press ENTER to engage the setting, then press ON-LINE to save the setting and exit the menu.
How do I activate the duplexer in the Windows PCL driver for the OKI DATA AMERICAS C5400N?
1. Click Start, then Settings, then Printers [Printers and Faxes for XP]. The Printers (Printers and Faxes) dialog box opens.
2. Right click the PCL printer icon, then click Properties.
3. Click the Device Option(s) tab.
4. Click Duplex Option Unit.
5. Click OK, then close the Printers (Printers and Faxes) dialog box.
How do I activate the duplexer in the Windows Postscript Emulation driver for the OKI DATA AMERICAS C5400N?
1. Click Start, then Settings, then Printers [Printers and Faxes for XP]. The Printers (Printers and Faxes) dialog box opens.
2. Right click the Postscript emulation printer icon, then click Properties.
3. Proceed based on your Windows version:
– Windows XP, 2000 and NT 4.0: click the Device Settings tab.
– Windows Me and 98: click the Device Options tab.
4. Under Installable Options, click Duplex and select Installed.
5. Click OK, then close the Printers (Printers and Faxes) dialog box.
How do I activate the duplexer on Macintosh OS 8.x and 9.x for the OKI DATA AMERICAS C5400N?
1. Activate Chooser from the Apple menu.
2. Select LaserWriter 8.
3. Click Printer, then Setup.
4. Click Configure.
5. Change the Duplex Unit setting to Installed.
6. Click OK twice.
7. Close Chooser.
Is activation required for the duplexer on Macintosh OS X to X.1 for the OKI DATA AMERICAS C5400N?
No, for OS X to X.1, no activation is required.
How do I activate the duplexer on Macintosh OS X.2 for the OKI DATA AMERICAS C5400N?
1. Activate Print Center from Local Hard Drive -> Applications -> Utilities -> Print Center.
2. Highlight the printer name and select from the menu Printers -> Show Info.
3. Click the box next to Duplex.
4. Click Apply Changes and exit to the desktop.
How do I set duplexing as the printing default on Macintosh OS Classic for the OKI DATA AMERICAS C5400N?
If you will always utilize duplex printing on OS Classic:
1. Access the printer driver via an application (File -> Print).
2. Select Layout in the drop down menu at the left.
3. Click the box to enable Print on Both Sides.
4. Select the desired binding position and make any other adjustments desired.
5. Click Save Settings.
How do I set duplexing as the printing default on Macintosh OS X for the OKI DATA AMERICAS C5400N?
If you will always utilize duplex printing on OS X:
1. Access the printer driver via an application (File -> Print).
2. Select Duplex in the drop down menu at the left.
3. Click the box to enable Print on Both Sides.
4. Select the desired binding position and make any other adjustments desired.
5. Save your printer profile preset with a descriptive name, e.g. Duplex Enabled.
6. Use this preset every time duplexing is required.
CLICK HERE TO DOWNLOAD OKI DATA AMERICAS C5400N (01) PDF DOCUMENT