Free English TP-LINK ARCHER A8 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD TP-LINK ARCHER A8 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What do the LED indicators on the TP-LINK ARCHER A8 signify?
The LEDs on the TP-LINK ARCHER A8 indicate the router’s working status. The following table explains the status of each LED:
| LED | Status | Indication |
|---|---|---|
| Power | On | The system has started up successfully. |
| Power | Flashing | The system is starting up or the firmware is being upgraded. Do not disconnect or power off your router. |
| Power | Off | Power is off. |
| 2.4GHz Wireless | On | The 2.4GHz wireless band is enabled. |
| 2.4GHz Wireless | Off | The 2.4GHz wireless band is disabled. |
| 5GHz Wireless | On | The 5GHz wireless band is enabled. |
| 5GHz Wireless | Off | The 5GHz wireless band is disabled. |
| LAN | On | At least one powered-on device is connected to the router’s LAN port. |
| LAN | Off | No powered-on device is connected to the router’s LAN port. |
| Internet | Green On | Internet service is available. |
| Internet | Orange On | The router’s Internet port is connected, but the internet service is not available. |
| Internet | Off | The router’s Internet port is unplugged. |
What are the functions of the buttons and ports on the back of the TP-LINK ARCHER A8?
The back panel of the TP-LINK ARCHER A8 features the following buttons and ports:
| Item | Description |
|---|---|
| Power Port | For connecting the router to a power socket via the provided power adapter. |
| Power On/Off Button | Press this button to power on or off the router. |
| Reset Button | Press and hold the button until all LEDs turn on to reset the router to its factory default settings. |
| WPS/Wi-Fi Button | Press the button for 1 second, and immediately press the WPS button on your client to start the WPS process. Press and hold the button for 5 seconds to turn on or off the wireless function of your router. |
| Internet Port | For connecting to a DSL/Cable modem, or an Ethernet jack. |
| Ethernet Ports (1/2/3/4) | For connecting your PC or other wired devices to the router. |
| Antennas | Used for wireless operation and data transmit. Upright them for the best Wi-Fi performance. |
How should I position the TP-LINK ARCHER A8 for optimal performance?
To position your TP-LINK ARCHER A8 correctly:
1. The product should not be located in a place where it will be exposed to moisture or excessive heat.
2. Place the router in a location where it can be connected to multiple devices as well as to a power source.
3. Make sure the cables and power cord are safely placed out of the way so they do not create a tripping hazard.
4. The router can be placed on a shelf or desktop.
5. Keep the router away from devices with strong electromagnetic interference, such as Bluetooth devices, cordless phones, and microwaves.
How do I connect the hardware for the TP-LINK ARCHER A8?
Follow these steps to connect your TP-LINK ARCHER A8:
1. Turn off your modem, if any, and remove the backup battery if it has one.
2. Connect the modem to the router’s Internet port with an Ethernet cable.
3. Turn on the modem, and then wait about 2 minutes for it to restart.
4. Connect the power adapter to the router and turn on the router.
5. Verify that the Power, 2.4GHz, 5GHz, and Internet LEDs are on and solid to confirm the hardware is connected. If the 2.4GHz LED and 5GHz LED are off, press and hold the WPS/Wi-Fi button on the back for more than 5 seconds, then release the button.
Note: If your internet connection is through an Ethernet cable directly from the wall instead of through a modem, connect the Ethernet cable to the router’s Internet port, and then follow steps 4 and 5.
How do I connect my computer to the TP-LINK ARCHER A8?
You can connect to the TP-LINK ARCHER A8 using two methods:
Method 1: Wired
Turn off the Wi-Fi on your computer and connect your computer to the router’s LAN port using an Ethernet cable.
Method 2: Wirelessly
1. Find the SSID (Network Name) and Wireless Password printed on the label at the bottom of the router.
2. Click the network icon of your computer or go to Wi-Fi Settings of your smart device, and then select the SSID to join the network.
How do I use the WPS button to connect a device to the TP-LINK ARCHER A8?
Wireless devices that support WPS can be connected to your TP-LINK ARCHER A8 through this method:
1. Tab the WPS icon on the device’s screen.
2. Within two minutes, press the WPS button on your router.
Note: WPS is not supported by iOS devices. The WPS function cannot be configured if the wireless function of the router is disabled or if the wireless encryption is WEP.
How do I log in to the web-based utility of the TP-LINK ARCHER A8?
1. Set up the TCP/IP Protocol in “Obtain an IP address automatically” mode on your computer.
2. Visit http://tplinkwifi.net. Create a login password for secure management purposes, then click “Let’s Get Started” to log in.
Note: If you have registered a TP-Link ID and bound your cloud router to it, the login password created here will be invalid. Please log in to the cloud router using your TP-Link ID.
How do I use the Quick Setup Wizard on the TP-LINK ARCHER A8?
1. Visit http://tplinkwifi.net and log in with the password you set for the router.
2. Follow the step-by-step instructions to complete Quick Setup configuration or go to Advanced > Quick Setup.
3. To enjoy more complete service from TP-Link, log in with your TP-Link ID or click “Sign Up Now” to get one, then bind the cloud router to your TP-Link ID.
How do I manually set up the internet connection on the TP-LINK ARCHER A8?
1. Visit http://tplinkwifi.net and log in with your TP-Link ID or password.
2. Go to Internet.
3. Select your internet connection type from the drop-down list (Dynamic IP, Static IP, PPPoE, L2TP, or PPTP).
4. Enter the specific information provided by your ISP corresponding to the connection type chosen.
5. Click Save.
How do I set up the TP-LINK ARCHER A8 as an Access Point?
1. Visit http://tplinkwifi.net and log in.
2. Go to Advanced > Operation Mode, select Access Point, and click Save. The router will reboot and switch to Access Point mode.
3. After rebooting, connect the router to your existing wired router via an Ethernet cable.
4. Log in again to the web management page http://tplinkwifi.net, and go to Advanced > Quick Setup.
5. Configure your wireless settings and click Next.
6. Confirm the information and click Save.
How do I set up an IPv6 internet connection on the TP-LINK ARCHER A8?
1. Visit http://tplinkwifi.net and log in.
2. Go to Advanced > IPv6.
3. Select the mode provided by your ISP. If you select “Pass-Through (Bridge)”, click Save. If you select “Router”, configure the WAN connection type (Normal, PPPoE, 6to4 Tunnel) and Get IPv6 Address settings as required by your ISP.
4. Keep the default LAN settings or modify if necessary.
5. Click Connect then click Save to apply your settings.
How do I create a Network for Guests on the TP-LINK ARCHER A8?
1. Visit http://tplinkwifi.net and log in.
2. Go to Advanced > Wireless > Guest Network.
3. Tick the Enable checkbox for the 2.4GHz or 5GHz wireless network.
4. Customize the SSID and select the Security type (No security or WPA/WPA2-Personal).
5. Click Save.
How do I set up Parental Controls on the TP-LINK ARCHER A8?
1. Visit http://tplinkwifi.net and log in.
2. Go to Advanced > Parental Controls.
3. Click Add to create a profile for a family member.
4. Enter a Name for the profile and add devices that belong to this profile.
5. Customize Blocked Content by entering keywords or URLs to block.
6. Set time restrictions by enabling Time Limits (daily allowance) and Bed Time (curfew hours).
7. Click Save.
How do I use QoS on the TP-LINK ARCHER A8 to prioritize devices?
1. Visit http://tplinkwifi.net and log in.
2. Go to Advanced > QoS > Global Settings.
3. Tick to enable QoS, input the maximum upload and download bandwidth, and click Save.
4. In the Device Priority section, find your computer or device.
5. Toggle on Priority.
6. Click the entry in the Timing column and select the duration you want the device to be prioritized for (e.g., 2 hours).
7. Click Save.
How do I use Access Control to block or allow specific devices on the TP-LINK ARCHER A8?
1. Visit http://tplinkwifi.net and log in.
2. Go to Advanced > Security > Access Control.
3. Toggle on to enable Access Control.
4. To block specific devices, select “Blacklist” as the Access Mode, click Add, select devices to block, and click ADD.
5. To allow only specific devices, select “Whitelist” as the Access Mode, click Save, then click Add to specify allowed devices.
How do I configure IP & MAC Binding on the TP-LINK ARCHER A8?
1. Visit http://tplinkwifi.net and log in.
2. Go to Advanced > Security > IP & MAC Binding.
3. Enable IP & MAC Binding.
4. Click Add in the Binding List section.
5. Click VIEW CONNECTED DEVICES and select the device you want to bind, or manually enter the MAC Address and IP Address.
6. Click Save.
How do I set up Port Forwarding on the TP-LINK ARCHER A8?
1. Visit http://tplinkwifi.net and log in.
2. Go to Advanced > NAT Forwarding > Port Forwarding.
3. Click Add.
4. Click VIEW COMMON SERVICES to select a service or manually enter the Internal Port, External Port, and Protocol.
5. Click VIEW CONNECTED DEVICES to select the device or manually enter the Device IP Address.
6. Click Save.
How do I configure Port Triggering on the TP-LINK ARCHER A8?
1. Visit http://tplinkwifi.net and log in.
2. Go to Advanced > NAT Forwarding > Port Triggering and click Add.
3. Click VIEW COMMON SERVICES and select the desired application or manually enter the Triggering Port, Triggering Protocol, and External Port.
4. Click Save.
How do I set up a DMZ host on the TP-LINK ARCHER A8?
1. Visit http://tplinkwifi.net and log in.
2. Go to Advanced > NAT Forwarding > DMZ and tick to enable DMZ.
3. Click VIEW CONNECTED DEVICES and select the device or enter the IP address of the DMZ host manually.
4. Click Save.
How do I change the LAN IP address of the TP-LINK ARCHER A8?
1. Visit http://tplinkwifi.net and log in.
2. Go to Advanced > Network > LAN.
3. Type in a new IP Address appropriate to your needs.
4. Click Save.
How do I configure IPTV/VLAN settings on the TP-LINK ARCHER A8?
1. Visit http://tplinkwifi.net and log in.
2. Go to Advanced > Network > IPTV/VLAN.
3. Tick Enable IPTV/VLAN.
4. Select the appropriate Mode according to your ISP (e.g., Bridge, Custom, or specific ISP profile).
5. Click Save.
How do I specify DHCP Server settings on the TP-LINK ARCHER A8?
1. Visit http://tplinkwifi.net and log in.
2. Go to Advanced > Network > DHCP Server.
3. Tick the Enable checkbox.
4. Enter the starting and ending IP addresses in the IP Address Pool.
5. Enter other parameters if required (Default Gateway, DNS).
6. Click Save.
How do I reserve an IP address for a specific client device on the TP-LINK ARCHER A8?
1. Visit http://tplinkwifi.net and log in.
2. Go to Advanced > Network > DHCP Server.
3. Click Add in the Address Reservation section.
4. Click VIEW CONNECTED DEVICES to select the device or enter the MAC address manually.
5. Enter the IP address to reserve for the client device.
6. Click Save.
How do I set up a Dynamic DNS Service Account on the TP-LINK ARCHER A8?
1. Visit http://tplinkwifi.net and log in.
2. Go to Advanced > Network > Dynamic DNS.
3. Select the DDNS Service Provider (TP-Link, NO-IP, or DynDNS).
4. If selecting TP-Link, log in with your TP-Link ID and click Register to enter a Domain Name.
5. If selecting NO-IP or DynDNS, enter the username, password, and domain name of your account.
6. Click LOGIN AND SAVE.
How do I change the wireless settings on the TP-LINK ARCHER A8?
1. Visit http://tplinkwifi.net and log in.
2. Go to Advanced > Wireless > Wireless Settings.
3. To change the SSID, enter a new name in “Network Name (SSID)”.
4. To change the password, enter a new password in the “Password” field.
5. Click Save.
How do I upgrade the firmware of the TP-LINK ARCHER A8?
Online Upgrade:
1. Visit http://tplinkwifi.net and log in.
2. Go to Advanced > System > Firmware Upgrade.
3. Click CHECK FOR UPGRADES. If new firmware is available, click UPGRADE.
Local Upgrade:
1. Download the latest firmware file from http://www.tp-link.com.
2. Visit http://tplinkwifi.net and log in.
3. Go to Advanced > System > Firmware Upgrade.
4. In the Local Upgrade section, click BROWSE to locate the file, then click UPGRADE.
How do I backup and restore configuration settings on the TP-LINK ARCHER A8?
1. Visit http://tplinkwifi.net and log in.
2. Go to Advanced > System Tools > Backup & Restore.
3. To backup: Click BACK UP to save a .bin file to your computer.
4. To restore: Click BROWSE to locate the backup file, then click RESTORE.
How do I reset the TP-LINK ARCHER A8 to factory default settings?
Method 1: Via Hardware
Press and hold the Reset button on the back of the router until all LEDs turn on.
Method 2: Via Software
1. Visit http://tplinkwifi.net and log in.
2. Go to Advanced > System Tools > Backup & Restore.
3. Click FACTORY RESTORE.
How do I change the login password for the TP-LINK ARCHER A8?
1. Visit http://tplinkwifi.net and log in.
2. Go to Advanced > System > Administration.
3. In the Change Password section, enter the old password, then the new password twice.
4. Click Save.
How do I set the system time and language on the TP-LINK ARCHER A8?
1. Visit http://tplinkwifi.net and log in.
2. Go to Advanced > System > Time & Language.
3. To change language, select from the drop-down list and click Save.
4. To set time, select “Get from Internet”, “Get from Managing Device”, or “Manually”. Configure accordingly and click Save.
How do I configure the TP-LINK ARCHER A8 to reboot regularly?
1. Visit http://tplinkwifi.net and log in.
2. Go to Advanced > System > Reboot.
3. Tick Enable in the Reboot Schedule section.
4. Specify the Reboot Time and Repeat frequency.
5. Click Save.
How do I control the LED status (Night Mode) on the TP-LINK ARCHER A8?
1. Visit http://tplinkwifi.net and log in.
2. Go to Advanced > System > LED Control.
3. Enable Night Mode.
4. Specify the LED off time period.
5. Click Save.
What should I do if I forget my wireless password for the TP-LINK ARCHER A8?
1. Connect your computer to the router using an Ethernet cable.
2. Visit http://tplinkwifi.net and log in.
3. Go to Wireless to retrieve or reset your wireless password.
Note: If you haven’t changed the default password, it is printed on the label of the router.
What should I do if I forget my web management password for the TP-LINK ARCHER A8?
If you are using a TP-Link ID, click “Forgot password” on the login page and follow instructions. Alternatively, press and hold the Reset button on the router until LEDs turn on to reset it, then visit http://tplinkwifi.net to create a new login password.
What should I do if I can’t log in to the web management page of the TP-LINK ARCHER A8?
Try the following:
1. Make sure your computer is connected correctly and LEDs are lit.
2. Ensure your computer is set to “Obtain an IP address automatically”.
3. Verify http://tplinkwifi.net or http://192.168.0.1 is entered correctly.
4. Use another web browser or computer.
5. Reset the router to factory defaults.
What should I do if I cannot access the internet after configuring the TP-LINK ARCHER A8?
1. Log in to the web management page and check the Internet Status under Advanced > Network > Status.
2. If IP Address is valid but no internet, manually configure DNS servers to 8.8.8.8 under Advanced > Network > DHCP Server.
3. If IP Address is 0.0.0.0, restart the modem and router.
4. Ensure the physical connection between router and modem is correct.
5. Clone the MAC address of your computer under Advanced > Network > Internet > MAC Clone.
6. Change the LAN IP address if there is a conflict (e.g., change to 192.168.2.1).
What should I do if I cannot find or connect to the wireless network of the TP-LINK ARCHER A8?
If you cannot find the network:
1. Check the WLAN LED indicator on the router.
2. Move closer to the router.
3. Go to Wireless Settings in the web interface and ensure the SSID is not hidden.
If you can find it but fail to connect:
1. Ensure you are not inputting the PIN instead of the Password. If asked for a PIN, choose “Connecting using a security key instead”.
2. Check for “Network Security Key Mismatch” errors and verify the password.
3. Check signal strength.
4. Change the wireless channel to 1, 6, or 11.
5. Re-install or update the wireless adapter driver on your computer.
CLICK HERE TO DOWNLOAD TP-LINK ARCHER A8 (01) PDF DOCUMENT