NVX MAGNEATO (01) PDF DOCUMENT

While parked, clamp the bracket at an air conditioning vent or at other places in the car, connect to the USB power cable, and adjust the angle of the device to accommodate convenience, safety, and optimal charging position.

While parked, remove the sticker from the base and attach it to a flat surface. Connect to the USB power cable and adjust the angle of the device to accommodate convenience, safety, and optimal charging position.

Attach the magnetic ring directly on the rear of your phone/device or to a protective case. Before doing so, you will need to locate the center of the charging connector on your phone/device.

To locate the wireless charging connector, refer to your phone’s user manual or you can try the following steps:

– Mount the MagNeato base and connect the USB to ensure it is on.

– Most new phones have the wireless charging feature always on. If your phone does not, then confirm it is turned on your phone.

– Slowly position and hold your phone against the MagNeato until you see your device charging begin. Locate the best position for charging (typically under the logo on the back of the phone or somewhat center).

– Use the included guide and attach the protective clear guard to your device or charger in the position where charging was working.

– Remove the sticker from the Magnet Ring and attach to the clear guard.

– Mount your phone/device and confirm charging still works.

– If charging does not work, then you will need to adjust the magnetic ring so you can mount AND charge your phone/device.

The NVX MAGNEATO includes a QuickCharge 3.0 USB charger for ultra-fast charging in your vehicle. If you are going to use it in your home, office or indoors, then please use an AC Adapter with USB and QuickCharge 3.0 if you desire the fastest possible charging. At a minimum, you must use a USB charging source with an actual 1.5A output. Insufficient input current may result in unstable charging.

Your device must support Quick Charge to receive any benefit.

This device is built to charge all Qi mobile devices. To ensure the best charge, adjust your phone to align with the coils embedded in the center of the device. On certain Qi-enabled mobile devices, the receiver coil is located at the bottom of your phone, and you will need to adjust the position of your phone to achieve optimal charging.

Some mobile phones respond a little slower when placed upon the MagNeato, and please be advised that this is due to the operating system of your phone, and not the MagNeato itself.

In order to protect person(s) against bodily injury and damage to property please follow these instructions:

1. Do not disassemble this device. Disassembling this device can lead to a short circuit, or leakage of the charging vessel. Disassembly also may cause a risk of fire or electric shock.

2. Do not expose this device to fire or water. Severely hot, humid, dusty or corrosive environments can cause circuit damage and leakage of the charging device.

3. If you use a pacemaker or a related medical device, please, consult the use of this product with a doctor. A pacemaker must be kept more than 22 cm (8.66 in) from the wireless charger. Electromagnetic waves of the charger could interfere the pacemaker.

4. Give proper training according to this manual to any person that uses this device. This device is not a toy.

5. Do not place credit cards (or any card with a magnetic strip), magnetic recording devices (such as CD’s or DVD’s), or similarly magnetic items too close to this device, as this may result in damage or data erasure to them.

It depends on the receiver in your phone. If the charging coil of the receiver in your phone is small, the heat dissipation may not be adequate, and this may cause excess heat to accumulate while charging. If this happens, remove your phone from the charger and let it cool.

Make sure you have found the optimal charging position of your device on the MagNeato.

Make sure your mobile device is QI-Standard supported. Also, make sure you are using an AC Adapter with a full 1.5A output.

The phone (receiver built-in) or external receiver coil that allows the wireless charging current may be different. Alternatively, your phone may be using an above-normal amount of power while in standby/sleep, such as refreshing background applications and web pages.

The MagNeato wireless charger emits non-ionizing radiation which studies have shown not harmful to humans.

Model: MagNeato

Input: DC 9V 1.67A 5V 1.5A

Output: DC 9V 1.1A 5V 1A

Dimension: 65 mm (Ø) 52.5 mm (H)

Weight: 60 g

Certificates: CE, ROHS, FCC