NATIONAL SUPPLY YH1801RV-1 (01) PDF MANUAL

NATIONAL SUPPLY YH1801RV-1 (01) PDF SUMMARY:

How do you remove the burner and venturi tube?

Turn the grill bottom side up. Remove screw “B” and do not lose the washer. Turn nut “A” counter-clockwise until the burner and tube are free.

---

How do you install a new burner and tube?

Reverse steps for removing the burner and tube. The venturi tube must fully engage the valve nut A to fully engage the threads on the venturi tube, and nut A must be turned to the full length of the threads.

---

What should you ensure regarding the flow of combustion and ventilation air?

Ensure that nothing is obstructing the flow of combustion and ventilation air and that the ventilation openings of the grill are free and clear from debris.

---

How should you clean the grill?

The grill should be cool to the touch before cleaning and storing. After each use, the appliance must be cleaned. To reduce the risk of a grease fire, always clean the drip tray and remove any grease from the inside of the grill using warm soapy water. The outside of the appliance can also be wiped down with warm soapy water. Use a brass bristled barbecue brush to scrub the stainless steel cooking grates, not a steel bristled wire brush. DO NOT use any cleaning solvents or abrasives to clean the grill.

---

What should you check before each use?

Before each use, always check/clean burner/Venturi tubes for insects and insect nests. A clogged tube can lead to a fire beneath the appliance. Also, visually inspect the grill, hoses, and fittings for any wear, damage, or blockage.

---

How do you check for gas leaks?

Use a solution of 1 part liquid dish detergent to 10 parts water. Agitate the solution until bubbles form, then apply to all fittings and inlet to the grill control valve. If a leak is detected and you are unable to correct it, return the unit to the dealer for repair.

---

What must you do during pressure testing of the gas supply piping system?

The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2psi (3.5kPa).

---

What are the minimum clearances from the grill to any combustible material?

Minimum clearance from grill to any combustible material must be 8" on the rear and 12" on either side of the grill. This appliance shall not be located under unprotected combustible constructions.

---

What should you do if hoses, fittings, or burners need to be replaced?

If hoses, fittings or burners need replaced, use only assemblies specified by the manufacturer.

---

What should you do if there is an oil or grease fire?

In the event of an oil or grease fire, do not attempt to extinguish with water. Immediately call the fire department. A Type BC or ABC fire extinguisher may, in some circumstances, contain the fire.

---

What should you do in the event of rain, snow, hail, sleet, or other forms of precipitation while cooking with oil or grease?

Cover the cooking vessel immediately and turn off the appliance burners and gas supply. Do not attempt to move the appliance or cooking vessel.

---

What precautions should you take when cooking?

When cooking, the appliance must be on a level, stable surface in an area clear of combustible material. An asphalt surface (blacktop) may not be acceptable for this purpose. Do not place an empty cooking vessel on the appliance while in operation. Use caution when placing anything in the cooking vessel while the appliance is in operation. Do not move the appliance while in use. Allow the cooking vessel to cool to 115ºF (45ºC) before moving or storing. Place hoses and tank in a position so as to avoid a trip hazard.

---

What should you do for protection from hot surfaces?

Use insulated oven mitts or gloves for protection from hot surfaces or splatter from cooking liquids.

---

What should you avoid when handling the appliance while it is in use?

Avoid bumping of or impact with the appliance to prevent spillage or splashing of hot cooking liquid.

---

What is the proper procedure for bracket installation?

The installation of the appliance mounting brackets must be performed by the recreational vehicle manufacturer and be in accordance with the requirements of ANSI A119.2/NFPA 1192 and ANSI A119.5.

---

What are the requirements for the convenience outlet installation?

The installation of the convenience outlet (quick disconnect and manual valve assembly) must be performed by the recreational vehicle manufacturer and be in accordance with the requirements of ANSI A119.2 /NFPA 1192 and ANSI A119.5.

---

What are the installation guidelines?

Installation of this grill must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1 / NFPA 54, Storage and Handling of Liquefied Petroleum Gases, ANSI / NFPA 58; or Natural Gas and Propane Installation Code, CSA B149.1; Propane Storage and Handling, CSA B149.2; or the Standard for Recreational Vehicles, ANSI A119.2 / NFPA 1192; and Recreational Vehicle Code, CSA Z240 RV Series, as applicable.

---

Where should the appliance be installed on an RV?

This appliance shall be installed on the opposite side, from a fuel distribution/dispensing system of an RV.

---

What should the installation of the appliance preclude?

The installation of the appliance must preclude the possibility of operation or gas flow when in storage (travel) position.

---

How should the recreational vehicle grill be connected to the vehicle’s propane system?

The recreational vehicle grill shall be connected to the vehicle’s propane system with a flexible hose connector complying with the high-pressure requirements of the Standard for Pigtails and Hose Connections for LP-Gas, ANSI/UL 569, and shall be of a length no longer than that required to allow the grill to be mounted in the “in use” position of its mounting system.

---

How should the hose be installed?

The hose shall be installed in a manner that will not allow it to come in contact with the hot surface of the grill while in use or in the storage/travel mode.

---

How do you unfold the bracket?

Unfold each arm one at a time. Arms will drop into slots.

---

How do you refold the bracket?

To refold; step on the bottom rail to push arms above slots. Fold back into position.

---

What should you do when setting up your grill?

Remove your grill from all interior and exterior packaging. Always make sure the cooking area is free from combustible material. Attach the hose assembly to your grill using the quick coupler.

---

How do you set up the grill on the RV?

Hang bracket on white aluminum mounting strip located on the side of the RV. Open 2 folding arms on the bracket, and make sure they lock in position. Slide grill onto 2 arms, make sure the grill is fully on the arms, against the stops. Insert retaining pins into arms. To remove the grill, simply slide it off the bracket arms.

---

How do you light the burner?

Check to make sure the control knob is in the OFF position. Open the hood. Push down and rotate counterclockwise to HIGH. Using a grill lighter or match, light the burner through the lighting hole located on the bottom of the grill. Once the burner is lit, adjust the control valve to the desired cooking temperature.

---

What should you always do before turning on the gas and lighting the burner?

Always open the hood before turning on the gas and lighting the burner. Failure to open the hood before lighting could cause an explosion.

---

What should you do if the burner flame is accidentally extinguished during operation?

Turn off the gas supply immediately by pushing the knob down and rotating clockwise to the Off position.