NANLITE FS-300B (01) PDF Document

The technical specifications for the NANLITE FS-300B are as follows:

Model No.: FS-300B

Rated power: 350W

Input: AC100-240V 50/60HZ

Color Temperature: 2700K-6500K

CRI: Average 96

TLCI: Average 97

The main components and their functions for the NANLITE FS-300B are:

1. Lock catch: For installing and disassembling the reflector and other accessories.

2. Umbrella hole: For installing and removing an umbrella.

3. Reflector: For gathering light to improve the central illumination.

4. Angle fixing knob: Allows for adjusting and fixing the illumination direction.

5. LCD screen: For displaying data.

6. Lamp body handle: To conveniently lift the lamp and adjust the direction of the light.

7. USB port: For updating the firmware.

8. Right knob: For selecting options and adjusting the color temperature in CCT mode.

9. MODE button: For switching between CCT mode, EFFECT mode, and MENU.

10. Power switch: For switching the fixture on or off.

11. Fuse base: For placing the fuse.

12. Left knob: For adjusting the DIM (dimming) and scrolling through different selections.

13. Power socket: AC power input socket.

14. Yoke: Designed for connecting the lamp to a light stand and adjusting the direction of the light.

15. Bracket fixing knob: For locking the light fixture to a stand and adjusting the horizontal direction of the light.

To install the reflector on your NANLITE FS-300B:

1. Ensure its mounting points align with the slots on the light fixture.

2. When aligned, push the reflector into place and rotate it in the direction shown on the light until it clicks into place.

To remove the reflector from your NANLITE FS-300B:

Press and hold the lock catch and rotate the reflector until it is free to be removed from the fixture.

Follow these steps to install an umbrella on your NANLITE FS-300B:

1. Loosen the angle fixing knob.

2. Insert the umbrella into the umbrella hole.

3. Tighten the angle fixing knob to lock the umbrella securely in place.

The NANLITE FS-300B supports 2.4G wireless protocol V1.0 and V2.0. The fixture should be set to V2.0 when using a WS-RC-C1 or WS-RC-C2 remote controller, and set to V1.0 when using other remote controllers.

To set the wireless protocol:

1. Press the MODE button to enter the MENU.

2. Rotate the “right knob” to navigate to the WIRELESS PROTOCOL setting.

3. Rotate the “left knob” to select either V1.0 or V2.0.

1. First, ensure that the power switch of the fixture is in the off position.

2. Connect the power cable to the power socket on the fixture and a suitable AC power source.

3. Turn on the power switch. The LCD screen will then turn on and display all the relevant information for the fixture.

To adjust the settings in CCT mode on your NANLITE FS-300B:

1. Press the MODE button repeatedly until the fixture is in CCT mode.

2. To adjust the brightness (DIM), rotate the “left knob”. The DIM range is from 0% to 100%.

3. To adjust the color temperature (CCT), rotate the “right knob”. The CCT range is from 2700K to 6500K.

When the fixture function is unlocked, in any mode, you can press the “left knob” to turn off the light. The brightness percentage on the screen will show 000%. Press the “left knob” again to restore the light to its previous state. You can press it continuously to switch between on and off.

To use the special effects on your NANLITE FS-300B:

1. Press the MODE button to switch to EFFECT mode.

2. The NANLITE FS-300B has built-in effects including CCT LOOP, INT LOOP, FLASH, PULSE, STORM, TV, PAPARAZZI, CANDLE/FIRE, BAD BULB, FIREWORK, EXPLOSION, and WELDING.

3. Rotate the “right knob” to scroll through and select the desired effect (FX).

After selecting an effect in EFFECT mode, use the “right knob” to choose a parameter to adjust (e.g., DIM, CCT, SPD) and then use the “left knob” to change its value. The adjustable parameters for each effect on the NANLITE FS-300B are:

CCT LOOP: Adjust DIM, CCT, and SPD (Speed, Range: 02S to 30S).

INT LOOP: Adjust DIM, CCT, and SPD (Speed, Range: 02S to 30S).

FLASH: Adjust DIM, CCT, and INTERVALS (Range: 0.1S to 10S).

PULSE: Adjust DIM, CCT, and PULSES/MIN (Range: 001 to 240).

STORM: Adjust DIM, CCT, and INTVL (Interval, Range: 1s to 60s).

TV: Adjust DIM, CCT, and SPD (Speed, Range: 001 to 100).

PAPARAZZI: Adjust DIM, CCT, and SPD (Speed, Range: 001 to 100).

CANDLE/FIRE: Adjust DIM, CCT, and SPD (Speed, Range: 001 to 100).

BAD BULB: Adjust DIM, CCT, and SPD (Speed, Range: 001 to 100).

FIREWORK: Adjust DIM, CCT, SPD (Range: 001 to 100), and DECAY (Range: 001 to 100).

EXPLOSION: Adjust DIM, CCT, SPD (Range: 001 to 100), and DECAY (Range: 001 to 100).

WELDING: Adjust DIM, CCT, SPD (Range: 001 to 100), and PAUSE (ON/OFF).

To access and navigate the MENU, press the MODE button until the MENU screen appears. Once in the MENU, rotate the “right knob” to select from the various options: CH, OUTPUT MODE, BLUETOOTH, WIRELESS PROTOCOL, FAN, FIRMWARE UPDATE, LANGUAGE, and VERSION.

First, enter the MENU by pressing the MODE button. Use the “right knob” to highlight the CH (channel) option. Then, rotate the “left knob” to set the desired channel.

To change the OUTPUT MODE on your NANLITE FS-300B:

1. Press the MODE button to enter the MENU.

2. Rotate the “right knob” to select OUTPUT MODE.

3. Rotate the “left knob” to select either MAX or CONSTANT mode.

To reset the Bluetooth on your NANLITE FS-300B:

1. Press the MODE button to switch to the MENU.

2. Rotate the “right knob” to navigate to the BT option.

3. Press the “right knob” to enter the Bluetooth reset interface.

4. Rotate the “right knob” to select RESET.

5. Press the “right knob” to confirm the reset. The fixture will return to the menu after the Bluetooth reset is complete.

To control the fan settings on your NANLITE FS-300B:

1. Enter the MENU and rotate the “right knob” to select FAN.

2. Rotate the “left knob” to select ON or OFF.

Note: When the fan is turned ON, the maximum output of the light will be 100%. When the fan is turned OFF, the maximum output of the NANLITE FS-300B is 25%.

To update the firmware on your NANLITE FS-300B:

1. Insert a USB flash drive with the latest firmware into the fixture’s USB port.

2. Press the MODE button to enter the MENU.

3. Rotate the “right knob” to select FW UPDATE.

4. Press the “right knob” to enter the firmware update interface. The fixture will search for the firmware file.

5. Once the firmware is found, rotate the “right knob” to select UPDATE.

6. Press the “right knob” to confirm the update. The screen will show “FIRMWARE UPDATED” after the update is completed.

To change the display language on your NANLITE FS-300B:

1. In the MENU, rotate the “right knob” to select LANGUAGE.

2. Rotate the “left knob” to select between the available language options.

To check the current firmware version of your NANLITE FS-300B, enter the MENU and rotate the “right knob” to highlight VERSION. The firmware version will be displayed on the screen.

To lock all functions on the NANLITE FS-300B, long press the “right knob”. A lock icon will appear on the LCD screen, and the current settings cannot be changed by rotating the knobs. To unlock, long press the “right knob” again.

Please follow these safety precautions when using your NANLITE FS-300B:

1. After opening the package, check for any possible damage caused in transit. If damage is found, do not use the fixture.

2. Do not use a power cable with damaged insulation. Do not unplug too hard or drag the power cable directly.

3. Before installation, make sure the voltage of the power supply accords with the voltage specified on the fixture.

4. Please turn the fixture off when it is not in use or before cleaning.

5. Please keep the fixture safely stored and away from children.

Please be aware of the following notices when using your NANLITE FS-300B:

1. Please remove the COB protective cap before using the fixture.

2. Please do not look directly at the emitter when the fixture is on.

3. Please wait for 10 seconds before turning off the fixture if parameter settings are done, in order to save the settings.

4. Please do not place any object on the fixture or allow liquid to flow inside the fixture.

5. Please do not place the fixture near any flammable or volatile substances like alcohol or gasoline.

6. Please do not use strong detergent for cleaning. Please wipe off the dirt by using a cloth with neutral cleanser when cleaning the fixture.

7. Please set up the fixture in a dry and well-ventilated place. Do not use it in any humid, dusty or overheated environment. Meanwhile, please also check whether the fan and vent are unimpeded.

8. Do not disassemble the fixture at will to repair by yourself. Qualified professionals should conduct maintenance.

9. Do not cover the vents when using, to avoid affecting heat dissipation and resulting in damage. Pay attention to anti-scald when using the fixture for a long time, since the surface temperature of the fixture will be high.

The box for the NANLITE FS-300B contains the following items:

Light Fixture x 1

Power Cable 4.5M x 1

Reflector x 1

COB Protective Cap x 1

User Manual x 1

If you encounter issues with your NANLITE FS-300B, please refer to the following diagnosis table. If the failure is not resolved after troubleshooting, please contact the place of purchase or manufacturer.